Front Speed Sensor: Installation

1. Using a 5 mm hexagon wrench, install the speed sensor with the bolt.

   Torque: 8.3 N*m (85 kgf*cm, 73 in.*lbf) 

   NOTE:

   • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
   • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip
   • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.
   • Make sure there is no foreign matter attached to the speed sensor rotor.

Fig 1: Locating Front Speed Sensor And Bolt (LH)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the connector.
2. Install the harness clamp with the bolt.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE:

   • When installing the clamp, do not twist the wire harness.
   • Make sure the clamp rotation stopper touches the installation position.
   Fig 2: Locating Harness Clamp And Sensor Wire

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 2 harness clamps with the 2 bolts.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE:

   • When installing the clamps, do not twist the wire harness.
   • Make sure the clamp rotation stopper touches the installation position.
   Fig 3: Locating Bolts And Harness Clamps

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the harness clamp with the nut.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE:

   • When installing the clamp, do not twist the wire harness.
   • Make sure the clamp rotation stopper touches the installation position.
   Fig 4: Locating Front Skid Control Sensor Connector And Clamp

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Install the harness clamp with bolt.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE: Install the bracket so that the rotation stopper touches the knuckle.
6. Connect the speed sensor connector.

Fig 5: Locating Harness Clamp With Bolt

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a 5 mm hexagon wrench, install the speed sensor with the bolt.

   Torque: 8.3 N*m (85 kgf*cm, 73 in.*lbf) 

   NOTE:

   • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
   • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip
   • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.
   • Make sure there is no foreign matter attached to the magnetic rotor.

Fig 6: Locating Front Speed Sensor And Bolt (RH)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the skid control sensor clamp with the bolt (labeled).

   Torque: for bolt A 

   5.0 N*m (51 kgf*cm, 44 in.*lbf) 

2. Attach the connector to the skid control sensor clamp and then connect the connector.
3. Install the 2 harness clamps with the 2 bolts.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE:

   • When installing the clamps, do not twist the wire harness.
   • Make sure the clamp rotation stopper touches the installation position.
   Fig 7: Locating Skid Control Sensor Clamp With Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the harness clamp with the nut.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE:

   • When installing the clamp, do not twist the wire harness.
   • Make sure the clamp rotation stopper touches the installation position.
   Fig 8: Locating Front Skid Control Sensor Connector And Harness Clamp

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Install the harness clamp with bolt.

   Torque: 13 N*m (127 kgf*cm, 9 ft.*lbf) 

   NOTE: Install the bracket so that the rotation stopper touches the knuckle.
6. Connect the speed sensor connector.

Torque: 131 N*m (1336 kgf*cm, 97 ft.*lbf) 

1. Check the speed sensor signal (See TEST MODE PROCEDURE  ).

Fig 9: Locating Harness Clamp With Bolt

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002