Freeze Frame Data
- FREEZE FRAME DATA
HINT:
- Whenever a DTC is detected or the ABS operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
- The skid control ECU stores the number of times (maximum: 31) the power switch has been turned from OFF to the ON (IG or READY) position since the last time ABS was activated. However, if the vehicle was stopped or at low speed (4.3 mph (7 km/h) or less), or if a DTC is detected, the skid control ECU will not count the number since then.
- Freeze frame data at the time the ABS operates: The skid control ECU stores and updates data whenever the ABS system operates. When the ECU stores data at the time a DTC is detected, the data stored when the ABS operated is erased.
- Freeze frame data at the time a DTC is detected: When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
- Connect the Teachstream to the DLC3.
- Turn the power switch ON (READY).
- From the display on the tester, select the FREEZE FRAME DATA.FREEZE FRAME DATA REFERENCE CHART
Tester Display Measurement Item Reference Value BUZZER Buzzer Buzzer ON: ON, OFF: OFF RESERVOIR WARNING SW Reservoir level warning switch Reservoir level warning switch ON: ON, OFF: OFF PARKING BRAKE SW Parking brake switch Parking brake switch ON: ON, OFF: OFF SHIFT POSITION Shift position Fail
P, N
R
D(M)
4
3
2
LVSC/TRC OFF SW VSC OFF switch VSC OFF switch ON: ON, OFF: OFF STOP LIGHT SW Stop light switch Stop light switch ON: ON, OFF: OFF SYSTEM SYSTEM ABS
VSC (TRC)
BA
HAB
FAIL SAFE
PBA
PB
NO SYSNumber of IG ON Number of operations of power switch on (IG) after storing Freeze Frame Data 0 to 31 VEHICLE SPD Vehicle speed Speed indicated on speedometer Steering Angle Sensor Steering sensor Left turn: Increase
Right turn: Drop (Deceleration)YAW RATE Yaw rate sensor -128 to 127 MAS CYL PRESS Master cylinder pressure 0 to 5V PEDAL STROKE Stroke sensor 0 to 5.1 V THROTTLE Throttle position sensor Release accelerator pedal:
Approx. 0 deg.
Depress accelerator pedal:
Approx. 125 deg.MAS PRESS GRADE Master pressure sensor grade 30 to 225 Mpa/s G (RIGHT & LEFT) Right and left G -1869 to 1869 G (BACK & FORTH) Back and forth G -1869 to 1869 SPD GRADE Vehicle speed grade -1869 to 1869 FR W/C SENS FR wheel cylinder pressure sensor 0 to 5 V FL W/C SENS FL wheel cylinder pressure sensor 0 to 5 V RR W/C SENS RR wheel cylinder pressure sensor 0 to 5 V RL W/C SENS RL wheel cylinder pressure sensor 0 to 5 V ACCUM PRESS Accumulator pressure sensor 0 to 5 V MAS CYL PRESS 2 Master cylinder pressure sensor 2 0 to 5 V PEDAL STROKE 2 Stroke sensor 2 0 to 5 V MTT MTT 0 to 5 V IG1 VOLTAGE Voltage value of IG1 0 to 20 V IG2 VOLTAGE Voltage value of IG2 0 to 20 V BS1 BS1 0 to 20 V BS2 BS2 0 to 20 V VM1 VM1 0 to 20 V VM2 VM2 0 to 20 V +B1 +B1 0 to 5 V +B2 +B2 0 to 5 V FR TARGET OIL Target oil pressure (FR) 0 to 20 V FL TARGET OIL Target oil pressure (FL) 0 to 20 V RR TARGET OIL Target oil pressure (RR) 0 to 20 V RL TARGET OIL Target oil pressure (RL) 0 to 20 V SLAFR Solenoid Current Current of SLAFR solenoid 0 to 1.5 A SLAFL Solenoid Current Current of SLAFL solenoid 0 to 1.5 A SLARR Solenoid Current Current of SLARR solenoid 0 to 1.5 A SLARL Solenoid Current Current of SLARL solenoid 0 to 1.5 A SLRFR Solenoid Current Current of SLRFR solenoid 0 to 1.5 A SLRFL Solenoid Current Current of SLRFL solenoid 0 to 1.5 A SLRRR Solenoid Current Current of SLRRR solenoid 0 to 1.5 A SLRRL Solenoid Current Current of SLRRL solenoid 0 to 1.5 A WHEEL SPD FR Front right wheel speed 0 to 255 km/h WHEEL SPD FL Front left wheel speed 0 to 255 km/h WHEEL SPD RR Rear right wheel speed 0 to 255 km/h WHEEL SPD RL Rear left wheel speed 0 to 255 km/h CAPA MODE Capacitor mode ON: ON, OFF: OFF ECB* Solenoid (SCSS) SCSS ON: ON, OFF: OFF ECB* Solenoid (SMC2) SMC2 ON: ON, OFF: OFF ECB* Solenoid (SMC1) SMC1 ON: ON, OFF: OFF MOTOR RELAY 2 Motor relay 2 ON: ON, OFF: OFF MOTOR RELAY 1 Motor relay 1 ON: ON, OFF: OFF ECB* MAIN RELAY 2 Main relay 2 for Electronically Controlled Brake ON: ON, OFF: OFF ECB* MAIN RELAY 1 Main relay 1 for Electronically Controlled Brake ON: ON, OFF: OFF FREEZE DTC Freeze frame DTC 0 to 255 DETAILED FREEZE DTC Detailed code for freeze DTC 0 to 65535 *: Electronically Controlled Brake.