Service Data

Axle

AXLE - SERVICE DATA

Front axle hub bearing looseness		Maximum looseness: 0.03 mm ((0.00118 in.)
Front axle hub runout		Maximum runout: 0.03 mm ((0.00118 in.)
Rear axle hub bearing looseness	for Torsion Beam Type Suspension	Maximum looseness: 0.05 mm (0.00196 in.)
Rear axle hub runout	for Torsion Beam Type Suspension	Maximum runout: 0.06 mm (0.00236 in.)
Rear axle hub bearing looseness	for Double Wishbone Type Suspension	Maximum looseness: 0.05 mm (0.00196 in.)
Rear axle hub runout	for Double Wishbone Type Suspension	Maximum runout: 0.07 mm (0.00275 in.)

Differential

DIFFERENTIAL - SERVICE DATA

Rear differential carrier oil seal installation depth		0.7 to 1.3 mm (0.0276 to 0.0512 in.)
Rear differential side gear shaft oil seal drive in depth		4.2 to 4.8 mm (0.165 to 0.189 in.)
Electro magnetic control coupling sub-assembly vertical runout	Maximum	0.04 mm (0.00157 in.)
Electro magnetic control coupling sub-assembly lateral runout.	Minimum	0.06 mm (0.00236 in.)
Drive pinion to ring gear backlash		0.10 to 0.15 mm (0.00394 to 0.00591 in.)
Side gear backlash		0.05 to 0.20 mm (0.002 to 0.0079 mm)
Drive pinion preload (at starting)	New bearing	0.7 to 1.3 Nm (7 to 13 kgfcm, 6 to 11 in.*lbf)
Drive pinion preload (at starting)	Reused bearing	0.4 to 0.7 Nm (4 to 7 kgfcm, 3 to 6 in.*lbf)
Total preload (Drive pinion preload plus)	New bearing	Standard drive pinion preload plus 0.7 to 1.3 Nm (7 to 13 kgfcm, 6 to 11 in.*lbf)
Total preload (Drive pinion preload plus)	Reused bearing	Standard drive pinion preload plus 0.29 to 0.49 Nm (3 to 5 kgfcm, 2.6 to 4.3 in.*lbf)
No. 1 side gear thrust washer thickness		1.48 to 1.52 mm (0.0583 to 0.0598 in.)
		1.53 to 1.57 mm (0.0602 to 0.0618 in.)
		1.58 to 1.62 mm (0.0622 to 0.0638 in.)
		1.63 to 1.67 mm (0.0642 to 0.0657 in.)
		1.68 to 1.72 mm (0.0661 to 0.0677 in.)
		1.73 to 1.77 mm (0.0681 to 0.0697 in.)

Differential / Rear differential side gear shaft washer plate thickness

DIFFERENTIAL / REAR DIFFERENTIAL SIDE GEAR SHAFT WASHER PLATE THICKNESS SPECIFICATIONS

25	1.59 to 1.61 mm (0.0626 to 0.0634 in.)
26	1.62 to 1.64 mm (0.0638 to 0.0646 in.)
27	1.65 to 1.67 mm (0.0650 to 0.0657 in.)
28	1.68 to 1.70 mm (0.0661 to 0.0669 in.)
29	1.71 to 1.73 mm (0.0673 to 0.0681 in.)
30	1.74 to 1.76 mm (0.0685 to 0.0693 in.)
31	1.77 to 1.79 mm (0.0697 to 0.0705 in.)
32	1.80 to 1.82 mm (0.0709 to 0.0717 in.)
33	1.83 to 1.85 mm (0.0720 to 0.0728 in.)
34	1.86 to 1.88 mm (0.0732 to 0.0740 in.)
35	1.89 to 1.91 mm (0.0744 to 0.0752 in.)
36	1.92 to 1.94 mm (0.0756 to 0.0764 in.)
37	1.95 to 1.97 mm (0.0768 to 0.0776 in.)
38	1.98 to 2.00 mm (0.0780 to 0.0787 in.)
39	2.01 to 2.03 mm (0.0791 to 0.0799 in.)
40	2.04 to 2.06 mm (0.0803 to 0.0811 in.)
41	2.07 to 2.09 mm (0.0815 to 0.0823 in.)
42	2.10 to 2.12 mm (0.0827 to 0.0835 in.)
43	2.13 to 2.15 mm (0.0839 to 0.0846 in.)
44	2.16 to 2.18 mm (0.0850 to 0.0858 in.)
45	2.19 to 2.21 mm (0.0862 to 0.0870 in.)
46	2.22 to 2.24 mm (0.0874 to 0.0882 in.)
47	2.25 to 2.27 mm (0.0886 to 0.0894 in.)
48	2.28 to 2.30 mm (0.0898 to 0.0906 in.)
49	2.31 to 2.33 mm (0.0909 to 0.0917 in.)
50	2.34 to 2.36 mm (0.0921 to 0.0929 in.)
51	2.37 to 2.39 mm (0.0933 to 0.0941 in.)
52	2.40 to 2.42 mm (0.0945 to 0.0953 in.)
53	2.43 to 2.45 mm (0.0957 to 0.0965 in.)
54	2.46 to 2.48 mm (0.0969 to 0.0976 in.)
55	2.49 to 2.51 mm (0.0980 to 0.0988 in.)
56	2.52 to 2.54 mm (0.0992 to 0.1000 in.)
57	2.55 to 2.57 mm (0.1004 to 0.1012 in.)
58	2.58 to 2.60 mm (0.1016 to 0.1024 in.)
59	2.61 to 2.63 mm (0.1028 to 0.1035 in.)
60	2.64 to 2.66 mm (0.1039 to 0.1047 in.)

Differential / Rear differential drive pinion plate washer thickness

DIFFERENTIAL / REAR DIFFERENTIAL DRIVE PINION PLATE WASHER THICKNESS SPECIFICATIONS

41	1.695 to 1.705 mm (0.0667 to 0.0671 in.)
42	1.705 to 1.715 mm (0.0671 to 0.0675 in.)
43	1.715 to 1.725 mm (0.0675 to 0.0679 in.)
44	1.725 to 1.735 mm (0.0679 to 0.0683 in.)
45	1.735 to 1.745 mm (0.0683 to 0.0687 in.)
46	1.745 to 1.755 mm (0.0687 to 0.0691 in.)
47	1.755 to 1.765 mm (0.0691 to 0.0695 in.)
48	1.765 to 1.775 mm (0.0695 to 0.0699 in.)
49	1.775 to 1.785 mm (0.0699 to 0.0703 in.)
50	1.785 to 1.795 mm (0.0703 to 0.0707 in.)
51	1.795 to 1.805 mm (0.0707 to 0.0711 in.)
52	1.805 to 1.815 mm (0.0711 to 0.0715 in.)
53	1.815 to 1.825 mm (0.0715 to 0.0719 in.)
54	1.825 to 1.835 mm (0.0719 to 0.0722 in.)
55	1.835 to 1.845 mm (0.0722 to 0.0726 in.)
56	1.845 to 1.855 mm (0.0726 to 0.0730 in.)
57	1.855 to 1.865 mm (0.0730 to 0.0734 in.)
58	1.865 to 1.875 mm (0.0734 to 0.0738 in.)
59	1.875 to 1.885 mm (0.0738 to 0.0742 in.)
60	1.885 to 1.895 mm (0.0742 to 0.0746 in.)
61	1.895 to 1.905 mm (0.0746 to 0.0750 in.)
62	1.905 to 1.915 mm (0.0750 to 0.0754 in.)
63	1.915 to 1.925 mm (0.0754 to 0.0758 in.)
64	1.925 to 1.935 mm (0.0758 to 0.0762 in.)
65	1.935 to 1.945 mm (0.0762 to 0.0766 in.)
70	1.945 to 1.955 mm (0.0766 to 0.0770 in.)
71	1.955 to 1.965 mm (0.0770 to 0.0774 in.)
72	1.965 to 1.975 mm (0.0774 to 0.0778 in.)
73	1.975 to 1.985 mm (0.0778 to 0.0781 in.)
74	1.985 to 1.995 mm (0.0781 to 0.0785 in.)
75	1.995 to 2.005 mm (0.0785 to 0.0789 in.)
76	2.005 to 2.015 mm (0.0789 to 0.0793 in.)
77	2.015 to 2.025 mm (0.0793 to 0.0797 in.)
78	2.025 to 2.035 mm (0.0797 to 0.0801 in.)
79	2.035 to 2.045 mm (0.0801 to 0.0805 in.)
80	2.045 to 2.055 mm (0.0805 to 0.0809 in.)
81	2.055 to 2.065 mm (0.0809 to 0.0813 in.)
82	2.065 to 2.075 mm (0.0813 to 0.0817 in.)
83	2.075 to 2.085 mm(0.0817 to 0.0821 in.)
84	2.085 to 2.095 mm (0.0821 to 0.0825 in.)
85	2.095 to 2.105 mm (0.0825 to 0.0829 in.)
86	2.105 to 2.115 mm (0.0829 to 0.0833 in.)
87	2.115 to 2.125 mm (0.0833 to 0.0837 in.)
88	2.125 to 2.135 mm (0.0837 to 0.0841 in.)
89	2.135 to 2.145 mm (0.0841 to 0.0844 in.)
90	2.145 to 2.155 mm (0.0844 to 0.0848 in.)
91	2.155 to 2.165 mm (0.0848 to 0.0852 in.)
92	2.165 to 2.175 mm (0.0852 to 0.0856 in.)
93	2.175 to 2.185 mm (0.0856 to 0.0860 in.)
94	2.185 to 2.195 mm (0.0860 to 0.0864 in.)
95	2.195 to 2.205 mm (0.0864 to 0.0868 in.)