LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2010 >> Prius Base >> Repair and Diagnosis >> General Information >> Identification >> Introduction (Except PHV) >> Repair Instruction >> Customize Parameters >> Customize Parameters
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Customize Parameters

NOTE:
  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

HINT: 

The following items can be customized.

  1. POWER DOOR LOCK CONTROL SYSTEM 
    DOOR LOCK

    Display Default Content Setting
    Unlock Key Twice ON Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. ON or OFF
    Auto Lock OFF
    ON*    		 Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF
    Auto Lock/Shift ON
    OFF*    		 Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed. ON or OFF
    Auto Unlock/Shift ON Function that unlocks all doors when the shift lever is moved to P from any position other than P while the power switch is on (IG). ON or OFF
    All Unlock/Open-Close OFF Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off. ON or OFF
    • *: for Korea
    ILLUMINATED ENTRY

    Display Default Content Setting
    Lighting Time 15 s Function that changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC) or (IG).) 7.5 s, 15 s or 30 s
  2. WIRELESS DOOR LOCK CONTROL SYSTEM 
    WIRELESS DOOR LOCK CONTROL SYSTEM

    Display (item) Default Function Setting
    Wireless Control ON Function that turns wireless door lock function on or off ON or OFF
    Hazard Answer Back ON When the doors are locked by wireless operation, the hazard warning lights flash once.
    When the doors are unlocked by wireless operation, the hazard warning lights flash twice.    		 ON or OFF
    Open Door Warning ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF
    Unlock 2 Operation ON Function that unlocks driver door when unlock switch on transmitter is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. ON or OFF
    Panic Function ON Function to operate theft deterrent system by continuously pressing panic switch on transmitter for 0.8 seconds ON or OFF
    Auto Lock Time 60 s*1 or 30 s*2 Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s
    Wireless Auto Lock ON This function turns the wireless auto lock function on or off. ON or OFF
    Wireless Buzzer Resp ON Wireless door lock buzzer response ON or OFF
    Wireless Buzzer Vol Level7 Wireless door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0
    • *1: except for Korea
    • *2: for Korea
    ILLUMINATED ENTRY

    Display Default Content Setting
    Lighting Time 15 s Changes the lighting time after closing all doors. (It will quickly fade out in case of turning the power switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s
  3. SMART KEY SYSTEM (for Entry Function) 
    SMART KEY / ACCESS

    Tester Display Default Content Setting
    Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s or 5 s
    Ignition Available Area All Function that switches the entry hybrid vehicle control system start detection area Front or All*1
    Back Door Opening Operation*2 Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF
    Door Unlock Mode*2, *3 Driver Function that chooses the doors to be operated by entry unlock operation All or Driver
    Touch Activation Over Threshold Active The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active
    • *1: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
    • *2: w/ Entry System Back Door Open Function
    • *3: except for Korea and Mexico
    WARNING

    Tester Display Default Content Setting
    Key Low Battery Warning ON Function that warns driver that the key battery is weak ON or OFF
  4. ENTRY UNLOCK MODE SWITCHING* (SMART KEY SYSTEM (for Entry Function)) 

    *: except for Korea and Mexico

    1. To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the lock switch and another switch on the key for 5 seconds.

      Driver door unlock default setting:

      When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

      NOTE:

      After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

      • Driver door unlock mode:

        When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.*

        *: w/ Entry System Back Door Open Function

      • All door unlock mode:

        When any touch sensor is touched, all doors unlock.

    2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart key system to entry unlock mode.
    3. The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly.
      Mode Wireless Door Lock Buzzer Assembly
      Driver Door
      (Default)      		 Sounds 3 times
      All Doors
      (Customized)      		 Sounds 2 times

      HINT: 

      The procedure only changes entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.

  5. ELECTRICAL KEY CANCEL (SMART KEY SYSTEM (for Entry Function)) 

    The electrical key cancel operation disables the following functions:

    • Entry Unlock/Lock
    • Entry Hybrid Vehicle Control System Start
    • Entry System Back Door Open Function*

      *: w/ Entry System Back Door Open Function

    • Electrical Key Lock-in Prevention
    • Warning
    1. The operation procedure is as follows:

      Precondition:

      Power switch off, driver door closed and unlocked.

      1. Push the unlock switch of the key once.
      2. Open the driver door within 5 seconds.
      3. Push the unlock switch of the key twice within 5 seconds.
      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.
      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  6. SMART KEY SYSTEM (for Start Function) 
    SMART KEY / ACCESS

    Tester Display Default Content Setting
    Ignition Available Area (Entry ignition available area) All Function to choose the available area for electrical key to start the hybrid control system. Front or All*
    • *: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
  7. CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (SMART KEY SYSTEM (for Start Function)) 

    Performing the following procedure disables the smart key system.

    HINT: 

    To start the hybrid control system while the smart key system is disabled, follow the procedure for when the key battery is low. Refer to SYSTEM DESCRIPTION .

    1. The operation procedure is as follows:

      Precondition:

      Power switch off, driver door closed and unlocked.

      1. Push the unlock switch of the key once.
      2. Open the driver door within 5 seconds.
      3. Push the unlock switch of the key twice within 5 seconds.
      4. Close and open the driver door twice within 30 seconds.

        (Driver door: Close → Open → Close → Open)

      5. Push the unlock switch of the key twice within 5 seconds.
      6. Close and open the driver door within 30 seconds.

        (Driver door: Close → Open)

      7. Close the driver door within 5 seconds.

        When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

        To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  8. LIGHTING SYSTEM (LIGHTING INT) 
    ILLUMINATED ENTRY

    Tester Display Default Content Setting
    Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) 7.5 s, 15 s or 30 s
    I/L when ACC OFF ON Lights up power switch illumination, front interior lights, rear interior light and footwell lights when the power switch is turned from on (ACC or IG) to off. ON or OFF
    I/L ON W/Door Key Unlock ON Lights up power switch illumination, front interior lights, rear interior light and footwell lights when doors are unlocked using a mechanical key or door control transmitter. ON or OFF
    Light Control ON Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:
    Power switch on (IG), shift lever not in P, and all doors closed.    		 ON or OFF
    Room Light when Aprchd ON Lights up the power switch illumination, front interior lights, rear interior light and footwell lights when a key enters any actuation area around the doors. ON or OFF
    Inside Foot Light ON Lights up the footwell lights when one of the following occurs: the power switch is turned on (IG), or any door is unlocked or opened. ON or OFF
  9. METER / GAUGE SYSTEM 
    WARNING

    Tester Display Default Content Setting
    Key Remind Sound Slow Function to change the cycle of the key reminder buzzer Normal, Fast or Slow
    Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF
    Front Passenger Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF
    Rear Seatbelt Warning Buzzer*2 ON Function to turn on/off the rear seat belt warning buzzer ON or OFF
    Reverse Buzzer Continual Function to change the type of the reverse warning buzzer Single or Continual
    • *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
    • *2: w/ Rear Seat Belt Warning
  10. SEAT BELT WARNING SYSTEM 
    COMBINATION METER

    Tester Display Default Content Setting
    Driver Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF
    Front Passenger Side Seatbelt Warning Buzzer ON Function to sound the seat belt warning buzzer ON / OFF

    HINT: 

    This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

  11. AIR CONDITIONING SYSTEM 
    AIR CONDITIONER

    Display (Item) Default Content Setting
    Set Temperature Shift Normal Function to control with the shifted temperature against the displayed temperature. +2 C, +1 C, Normal, -1 C or -2 C
    Compressor Mode Automatic Function to automatically turn the A/C on by pressing the AUTO button when blower is on and the A/C is off. Manual or Automatic
    Air Inlet Mode Automatic Function to shift from INLET mode to RECIRCULATION mode when the A/C is turned on. Manual or Automatic
    Foot/DEF Auto Mode ON Function to automatically turn the airflow from FOOT/DEF on when AUTO mode is on. OFF or ON
    Foot/DEF Automatic Blow Up Function ON Function to automatically increase the blower level when the defroster is on. OFF or ON
    Ambient Temperature Shift Normal Function to control the shifted ambient temperature in relation to the displayed ambient temperature. +3 C, +2 C, +1 C, Normal, -1 C, -2 C or -3 C
    ECO MODE Cancel OFF Function to cancel the ECO mode drive when item is on. OFF or ON
    Noise and Vibration Reduction OFF Function to change speed of the compressor when item is on. OFF or ON
    Start Pre A/C*1 Long1 Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2
    Stop Pre A/C*1 2 tim ON Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2
    • *1: w/ Remote Air Conditioning System
  12. LIGHTING SYSTEM (LIGHTING EXT) 
    LIGHT CONTROL

    Display Default Content Setting
    Disp Ex ON Sen Normal Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2
    Disp Ex OFF Sen Normal Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock. Light2, Light1, Normal, Dark1 or Dark2
    Light Auto OFF Delay 30 s Keeps the headlights on for a certain period of time after turning the power switch off and closing all the doors with the low beam headlights on. Off, 30 s, 60 s or 90 s
    Sensitivity Normal Adjusts the sensitivity of the automatic light control system. Light2, Light1, Normal, Dark1 or Dark2
    Response Time*1 0.1 s Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position 0.1 s or 1.0 s
    • *1: for Korea
scientia non olet · About LEMON Manuals