Service Data
| Spark plug | Standard resistance | 10 MΩ or more | |
| Recommended spark plug | SK20R11 DENSO made | ||
| IFR6A11 NGK made | |||
| Electrode gap | 1.0 to 1.1 mm (0.0394 to 0.0433 in.) | ||
| Maximum electrode gap | 1.3 mm (0.0512 in.) for used plug | ||
| Camshaft oil control valve | 1 - 2 | Resistance: 6.9 to 7.9 Ω at 20°C (68°F) |
|
| Throttle body | 1 (M-) - 2 (M+) | Resistance: 0.3 to 100 Ω at 20°C (68°F) |
|
| Accelerator pedal | Accelerator position No. 1 standard voltage | Accelerator pedal is released | 0.5 to 1.1 V |
| Accelerator pedal is depressed | 2.6 to 4.5 V | ||
| Accelerator position No. 2 standard voltage | Accelerator pedal is released | 1.2 to 2.0 V | |
| Accelerator pedal is depressed | 3.4 to 5.0 V | ||
| Mass air flow meter | Engine not running 30 seconds after ignition switch is turned to ON |
Less than 0.48 g/sec. | |
| 1 (THA) - 2 (E2) | Resistance: 13.6 to 18.4 kΩ at -20°C (-4°F) 2.21 to 2.69 kΩ at 20°C (68°F) 0.493 to 0.667 kΩ at 60°C (140°F) |
||
| Camshaft position sensor | 1 - 2 | Resistance: 835 to 1400 Ω at -10 to 50°C (14 to 122°F) 1060 to 1645 Ω at 50 to 100°C (122 to 212°F) |
|
| Crankshaft position sensor | 1 - 2 | Resistance: 985 to 1600 Ω at -10 to 50°C (14 to 122°F) 1265 to 1890 Ω at 50 to 100°C (122 to 212°F) |
|
| Engine coolant temperature sensor | 1 - 2 | Resistance: 2.32 to 2.59 kΩ at 20°C (68°F) 0.310 to 0.326 kΩ at 80°C (176°F) |
|
| Knock sensor | 1 - 2 | Resistance: 120 to 280 kΩ Always |
|
| Air fuel ratio sensor | (HA1A) - (+B) | Resistance: 1.8 to 3.4 Ω at 20°C (68°F) |
|
| (HA1A) - (A1A-) | Resistance: 10 kΩ or higher |
||
| Heated oxygen sensor | (HT1B) - (+B) | Resistance: 11 to 16 Ω at 20°C (68°F) |
|
| (HT1B) - (E2) | Resistance: 10 kΩ or higher |
||
| Integration relay (EFI MAIN RELAY) |
1E-1 - 1B-4 | Resistance: 10 kΩ or higher (Battery voltage is not applied between terminals 1B-3 and 1B-2) |
|
| Resistance: Below 1 Ω (Battery voltage is applied between terminals 1B-3 and 1B-2) |
|||
| Integration relay (IG2 RELAY) |
1E-1 - 1A-4 | Resistance: 10 kΩ or higher (Battery voltage is not applied between terminals 1A-2 and 1A-3) |
|
| Resistance: Below 1 Ω (Battery voltage is applied between terminals 1A-2 and 1A-3) |
|||
| Integration relay (HORN RELAY) |
1E-1 - 1A-8 | Resistance: 10 kΩ or higher (Battery voltage is not applied between terminals 1A-6 and 1A-7) |
|
| Resistance: Below 1 Ω (Battery voltage is applied between terminals 1A-6 and 1A-7) |
|||
| Circuit opening relay | 2A-8 - 2B-11 | Resistance: 10 kΩ or higher (Battery voltage is not applied between terminals 2B-10 and 2B-9) |
|
| Resistance: Below 1 Ω (Battery voltage is applied between terminals 2B-10 and 2B-9) |
|||