Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | WORKING WITH A/C SERVICE STATION (R1234yf) WORKING WITH A/C SERVICE STATION (R134a) |
||
| Torque | OVERVIEW - A/C COMPRESSOR POWER UNIT | ||
| Axle Nut/Hub Nut | |||
| Front | 200 Nm + 180° additional turn | ||
| Rear | 200 Nm + 90° additional turn | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC SYSTEM, STANDARD BLEEDING | ||
| Disc Brakes | |||
| Front | FRONT BRAKES, FN 3 | ||
| Rear | |||
| Torque | |||
| Front | OVERVIEW - FRONT BRAKES | ||
| Rear | OVERVIEW - REAR BRAKES | ||
| Charging | |||
| Generator | N/A | ||
| Torque | |||
| Drive Belts | |||
| Adjustment | |||
| 1.8L | RIBBED BELT, REMOVING AND INSTALLING | ||
| 2.0L | RIBBED BELT, REMOVING AND INSTALLING | ||
| 3.6L | RIBBED BELT, REMOVING AND INSTALLING | ||
| Belt Routing | |||
| 1.8L | See the figure under Installing | ||
| 2.0L | See the figure under Installing | ||
| 3.6L | See the figure under Installing | ||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 1.8L | 1.4 to 1.6 bar (20.3 to 23.2 psi) | ||
| 2.0L | 1.4 to 1.6 bar (20.3 to 23.2 psi) | ||
| 3.6L | 1.4 to 1.6 bar (20.3 to 23.2 psi) | ||
| Thermostat R & I | |||
| 1.8L | COOLANT THERMOSTAT HOUSING, REMOVING AND INSTALLING | ||
| 2.0L | OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT | ||
| 3.6L | COOLANT THERMOSTAT, REMOVING AND INSTALLING | ||
| Water Pump R & I | |||
| 1.8L | COOLANT PUMP, REMOVING AND INSTALLING | ||
| 2.0L | COOLANT PUMP, REMOVING AND INSTALLING | ||
| 3.6L | COOLANT PUMP, REMOVING AND INSTALLING | ||
| Engine Mechanical | |||
| 1.8L | |||
| Compression | COMPRESSION, CHECKING | ||
| Oil Pressure | OIL PRESSURE, CHECKING | ||
| Overhaul | 10 ENGINE, REMOVING AND INSTALLING 13 CRANKSHAFT 15 CYLINDER HEAD AND VALVETRAIN |
||
| Torque | Refer to the appropriate procedure in 10 ENGINE, REMOVING AND INSTALLING , 13 CRANKSHAFT or 15 CYLINDER HEAD AND VALVETRAIN | ||
| 2.0L | |||
| Compression | COMPRESSION, CHECKING | ||
| Oil Pressure | OIL PRESSURE, CHECKING | ||
| Overhaul | 10 ENGINE ASSEMBLY 13 CRANKSHAFT, CYLINDER BLOCK 15 CYLINDER HEAD, VALVETRAIN |
||
| Torque | Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN | ||
| 3.6L | |||
| Compression | COMPRESSION, CHECKING | ||
| Oil Pressure | OIL PRESSURE, CHECKING | ||
| Overhaul | 10 ENGINE, REMOVING AND INSTALLING 13 CRANKSHAFT 15 CYLINDER HEAD AND VALVETRAIN |
||
| Torque | Refer to the appropriate procedure in 10 ENGINE, REMOVING AND INSTALLING , 13 CRANKSHAFT and 15 CYLINDER HEAD AND VALVETRAIN | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Engine Oil Drain Plug | 30Nm | ||
| Flywheel/Flex Plate Torque | 60 Nm + an additional 90° (1/4) turn | ||
| Fuel System | |||
| Fuel Pressure Test Procedure | |||
| 1.8L | FUEL PRESSURE, CHECKING | ||
| 2.0L | FUEL PRESSURE, CHECKING | ||
| 3.6L | FUEL PRESSURE, CHECKING | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 1.8L | 06K 905 601D | ||
| 2.0L | 06K 905 601D | ||
| 3.6L | 101 905 622 | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | OVERVIEW - STARTER | ||
| Wheel Alignment | |||
| Adjustment Specifications | VEHICLE ALIGNMENT | ||
| Torque | 40 FRONT SUSPENSION 42 REAR SUSPENSION |
||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 Ft. Lbs. (140 Nm) | ||