Automatic Transmission - General Servicing, Removal And Installation
- Transmission
- Installing cross member
- Oil grade, checking
- Check the oil
- Removing transmission
- Notes
- Disconnecting battery lead
- Removing engine compartment components
- Removing upper torque rod
- Continue removing engine compartment components
- Removing torque control arm
- Removing transmission cable from lever and screws for cable bracket on transmission
- Removing mounting screws for transmission / starter motor
- Installing lifting hook, part 1
- Installing lifting hook, part 2
- Installing lifting beam and lifting hook on engine
- Removing air baffle and splash guard under engine
- Draining transmission fluid
- Removing nuts and screws for steering gear sub-frame
- Hanging up steering gear in a tie strap (use hole in body)
- Removing screws for cable conduit and ground lead bracket on sub-frame
- Removing nut for lower ball joint / control arm
- Removing control arms and tie rod (both sides)
- Removing screws from sub-frame support plates (both sides)
- Removing wheel spindle from control arm
- Removing drive shaft from wheel spindle (right-hand side)
- Removing cap for the drive shaft support bearing
- Removing drive shaft
- Press up sub-frame on right-hand side
- Removing charge air pipe for turbocharger (TC) under engine
- Removing torque rod from transmission screws
- Removing screw from starter motor and exhaust pipe from turbocharger (TC)
- Removing front cross member
- Removing rear engine pad screw
- Removing rear engine mounting
- Preparatory work for removing wheel spindle on left-hand side
- Removing left drive shaft from transmission
- Lowering sub-frame
- Lowering engine and transmission
- Removing collision protection system over steering gear
- Removing torque converter screws
- Removing transmission / engine screw
- Preparations for removal of transmission
- Installing fixture on mobile jack and transmission
- Removing transmission
- Checking carrier plate
- Checking / replacing torque converter
- Replacing carrier plate
- Oil level, checking, -2001
- Oil level, checking, 2002-
- Oil, quality check
- Removing / installing transmission
- Notes
- Removing
- Introduction
- Removing components in engine compartment
- Disconnecting components in engine compartment
- Disconnecting transmission connectors
- Removing transmission-engine-starter motor screws
- Installing hoist
- Removing front wheel and splash guards
- Removing components left and right-hand sides:
- Disconnecting drive shaft, left-hand side
- Removing, left-hand side:
- Removing heat deflector plate and member
- Removing right-hand side
- Disconnecting oil pipes
- Removing torque converter screws
- Lowering engine
- Connecting fixture
- Removing engine-transmission screws
- Removing transmission
- Cleaning and inspection
- Installing
- Installing transmission
- Lifting engine and transmission
- Installing transmission-engine screws
- Installing torque converter screws
- Installing front and rear brackets
- Installing left/right drive shafts
- Checking drive shafts
- Installing longitudinal member
- Installing oil pipes
- Tightening stub axle/installing ABS and brake lines
- Installing splash guards and wheels
- Installing, continued
- Installing gear selector cable
- Installing other components
- Installing wheels
- Finishing
- Checking oil level
- Filling in diagnostic and check lists
- Returning transmission (only when replacing entire transmission assembly)
- Tightening torque
- Removing transmission
- Notes
- Disconnect battery lead
- Remove engine compartment components
- Install lifting hook
- Remove hose for clutch cylinder
- Disconnect connectors. Disconnect transmission cables
- Remove gear selector housing
- Remove screw and tie strap for cable harness and ground lead
- Remove screw and clamp for servo oil pipe
- Remove screws for transmission / engine
- Install lifting beam and lifting hook on engine lifting lugs
- Remove suspension components
- Remove screws for cable conduit and ground lead bracket on sub-frame
- Remove nut for lower ball joint / control arm
- Remove control arms and tie rod from both sides
- Remove screws from sub-frame support plates (both sides)
- Remove wheel spindle from control arm
- Press up sub-frame on right-hand side
- Remove drive shaft from wheel spindle (right-hand side)
- Remove support bearing cap from drive shaft
- Remove drive shaft
- Remove front cross member
- Remove bracket for heated oxygen sensor (HO2S) wiring
- Remove steering gear nuts and screw from sub-frame
- Preparatory work for removing wheel spindle on left-hand side
- Remove left drive shaft from transmission
- Lower sub-frame
- Remove collision protection
- Remove screw for rear engine pad
- Remove rear engine mounting
- Remove screw for front engine pad. Remove torque rod screws in transmission
- Lower engine with transmission
- Preparations for removal of transmission
- Install fixture on mobile jack
- Locate fixture against transmission
- Remove transmission
- Splines greasing
- Resetting adaptation
- Resetting transmission fluid change counter