Brake Control Module (BCM) DTCS
BRAKE CONTROL MODULE (BCM) - DTC INDEX
| DTC | Description |
|---|---|
| BCM-0010 | Left front wheel sensor. Signal missing |
| BCM-0011 | Left front wheel sensor. Faulty signal |
| BCM-0012 | Left front wheel sensor. Faulty signal |
| BCM-0020 | Right front wheel sensor. Signal missing |
| BCM-0021 | Right front wheel sensor. Faulty signal |
| BCM-0022 | Right front wheel sensor. Faulty signal |
| BCM-0030 | Left rear wheel sensor. Signal missing |
| BCM-0031 | Left rear wheel sensor. Faulty signal |
| BCM-0032 | Left rear wheel sensor. Faulty signal |
| BCM-0040 | Right rear wheel sensor. Signal missing |
| BCM-0041 | Right rear wheel sensor. Faulty signal |
| BCM-0042 | Right rear wheel sensor. Faulty signal |
| BCM-0050 | Control module. Faulty signal |
| BCM-0052 | Control module. Internal fault |
| BCM-0057 | Power supply. Voltage too low |
| BCM-0058 | Power supply. Voltage too high |
| BCM-0061 | Brake discs. Temperature too high |
| BCM-0065 | Stop lamp switch. Faulty signal |
| BCM-0068 | Sensor power supply. Faulty signal |
| BCM-0070 | Power supply for the pump motor. Faulty signal |
| BCM-0071 | Pump motor. Signal missing |
| BCM-0072 | Pump motor. Mechanical fault |
| BCM-0074 | Hydraulic valves. Faulty signal |
| BCM-0076 | Control module. Faulty configuration |
| BCM-0080 | Lateral accelerometer. Incorrect offset value |
| BCM-0081 | Accelerometer. Incorrect offset value |
| BCM-0082 | Yaw rate sensor. Incorrect offset value |
| BCM-0083 | Angle of lean sensor. Incorrect offset value |
| BCM-0090 | Lateral accelerometer. Faulty signal |
| BCM-0091 | Accelerometer. Faulty signal |
| BCM-0092 | Yaw rate sensor. Faulty signal |
| BCM-0093 | Angle of lean sensor. Faulty signal |
| BCM-0094 | Communication between control units Communication problems with DEM |
| BCM-0095 | Communication between control units Communication problems with DEM |
| BCM-0097 | Communication between control modules. Communication problems with the central electronic module (CEM) |
| BCM-0100 | Communication between control modules. Communication problems with the engine control module (ECM) |
| BCM-0101 | Communication between control modules. Communication problems with the engine control module (ECM) |
| BCM-0103 | Pedal position sensor. Faulty signal |
| BCM-0106 | Steering wheel or wheel alignment. Incorrect steering wheel or wheel alignment |
| BCM-0108 | Communication between control modules. Communication with the steering angle sensor. Control module not initiated |
| BCM-0109 | Communication between control modules. Communication with the steering angle sensor. Internal fault |
| BCM-0111 | Communication between control modules. Check of the steering angle sensor tolerances has not been run |
| BCM-0112 | Active yaw control sensor. Sensor not calibrated |
| BCM-0113 | Back-up (reversing) signal. Signal missing |
| BCM-0114 | Communication with the active yaw control sensor. Signal missing |
| BCM-0115 | Communication between control modules. Communication with the steering angle sensor. Signal missing |
| BCM-0116 | Communication with the active yaw control sensor. Communication problems |
| BCM-0117 | Communication with the active yaw control sensor. An incorrect active yaw control sensor had been installed |
| BCM-0118 | Power supply for the active yaw control sensor. Voltage too high |
| BCM-0119 | Power supply for the active yaw control sensor. Voltage too low |
| BCM-0121 | Yaw rate sensor. Signal outside its permitted range |
| BCM-0123 | Active yaw control sensor. Internal fault |
| BCM-0125 | Lateral accelerometer. Signal outside its permitted range |
| BCM-0127 | Angle of lean sensor. Signal outside its permitted range |
| BCM-0129 | Accelerometer. Signal outside its permitted range |
| BCM-0130 | Brake pressure sensor 1. Signal too low |
| BCM-0133 | Brake pressure sensor 2. Signal too low |
| BCM-0136 | Brake pressure sensor 1 and 2. Signal outside its permitted range |
| BCM-0138 | Power supply for the active yaw control sensor. Faulty voltage |
| BCM-0139 | Pressure build-up valve, power brake booster. Signal outside its permitted range |
| BCM-0140 | Pedal pressure sensor. Signal outside its permitted range |
| BCM-0145 | Stability control. Too long stability control |
| BCM-0146 | Factory test, dynamic stability and traction control (DSTC). Test cycle not approved |
| BCM-0147 | Pedal position sensor. Signal outside its permitted range |
| BCM-0148 | Communication between control modules. Faulty configuration ID |
| BCM-0150 | Stop lamp switch. Signal outside its permitted range |
| BCM-0151 | Control module. Internal memory fault |
| BCM-A030 | Communication between control modules. Steering angle sensor. Initialization check not run |
| BCM-A031 | Communication between control modules. Steering angle sensor. Tolerance check not run |
| BCM-A032 | Stability function. Too long stability control |
| BCM-E000 | Control module communication. Faulty communication |
| BCM-E003 | Configuration fault. Faulty configuration |
| BCM-XXXX | Unknown diagnostic trouble code (DTC) for the current control module version |