Driving Position Memory System Input Test And Function Test
1. Connect the HDS to the data link connector (DLC) .
2. Press the engine start/stop button to select the ON mode.
3. From the BODY ELECTRICAL SYSTEM SELECTION menu, select POWER SEAT/POWER MIRROR, then DTCs.
- If DTCs are found, troubleshoot the DTCs.
- If no DTCs are found, go to step 4.
4. Exit the DTC mode, and select the DATA LIST from the POWER SEAT/POWER MIRROR TEST MODE MENU.
5. Test each input and monitor each output under the condition shown below:
- If the data list indication is correct, continue to the next switch. If all switches are OK, go to step 7.
- If the data list indication is not correct, do the appropriate test at the control unit and terminal indicated in the table.
- Voltage drop tests should be done with the vehicle ignition in the ON mode, and all connectors connected and the meter negative test lead attached to a good body ground, unless specified otherwise.
- Continuity tests should be done with the vehicle ignition in the OFF mode, and indicated terminals disconnected.
| Data List Input/Command | Condition: Data List Indication | Control Unit/Terminal Number/Test (If applicable) | Possible cause if desired result is not obtained |
|---|---|---|---|
| Slide Switch Forward | Slide switch forward: ON Switch released: OFF |
Power seat control unit/B14, B20 Slide switch forward: 0 V Switch released: 5 V |
|
| Slide Switch Backward | Slide switch backward: ON Switch released: OFF |
Power seat control unit/B20, B37 Slide switch backward: 0 V Switch released: 5 V |
|
| Recline Switch Forward | Recline switch forward: ON Switch released: OFF |
Power seat control unit/B15, B20 Recline switch forward: 0 V Switch released: 5 V |
|
| Recline Switch Backward | Recline switch backward: ON Switch released: OFF |
Power seat control unit/B20, B38 Recline switch backward: 0 V Switch released: 5 V |
|
| Front Up-Down Switch Up | Front up-down switch up: ON Switch released: OFF |
Power seat control unit/B16, B20 Front up-down switch up: 0 V Switch released: 5 V |
|
| Front Up-Down Switch Down | Front up-down switch down: ON Switch released: OFF |
Power seat control unit/B17, B20 Front up-down switch down: 0 V Switch released: 5 V |
|
| Rear Up-Down Switch Up | Rear up-down switch up: ON Switch released: OFF |
Power seat control unit/B20, B39 Rear up-down switch up: 0 V Switch released: 5 V |
|
| Rear Up-Down Switch Down | Rear up-down switch down: ON Switch released: OFF |
Power seat control unit/B18, B20 Rear up-down switch down: 0 V Switch released: 5 V |
|
| Ignition Switch for Power Seat Control | Power mode ON: ON Power mode OFF: OFF |
Power seat control unit/B27 Power mode ON: 12 V Power mode OFF: 0 V |
|
| ATP Switch | Transmission range switch P position: ON Any other position than P: OFF |
Power seat control unit/B35 Transmission range switch P: 0 V Any other position than P: 12 V |
|
| Slide Sensor | Seat moving forward or backward: ON Seat not moving: OFF |
Power seat control unit/B10 Pulses as seat moves: 2.5 V average |
|
| Front Up-Down Sensor | Seat front moving up/down: ON Seat not moving: OFF |
Power seat control unit/B9 Pulses as seat moves: 2.5 V average |
|
| Recline Sensor | Seat-back moving forward or backward: ON Seat not moving: OFF |
Power seat control unit/B11 Pulses as seat moves: 2.5 V average |
|
| Rear Up-Down Sensor | Seat rear moving up/down: ON Seat not moving: OFF |
Power seat control unit/B8 Pulses as seat moves: 2.5 V average |
|
6. Exit the DATA LIST and select FUNCTIONAL TESTS.
7. Do each of the function tests listed in the table shown. The appropriate output should occur.
- If the function operates normally, go to the next function test. If all function tests operate normally, the system is OK.
- If the function does not occur, do the appropriate test at the control unit and terminal indicated in the table.
- Voltage drop tests should be done with the vehicle ignition in the ON mode, and all connectors connected.
- Continuity tests should be done with the vehicle ignition in the OFF mode, and indicated terminals disconnected.
- Jumper tests should be done according to the instructions indicated.
- If the test indicates that the component operates normally, but the function will not operate by doing the function test or normal use of the component, the control unit that operates that function must be faulty; replace it.
- If the test indicates that the component does not operate normally, check for an open or short in the harnesses between the component and the control unit. If the harness is OK, replace the component.
| Function Test | Component and Operation | Control Unit/Terminal Number/Test (If applicable) | Possible cause if desired result is not obtained |
|---|---|---|---|
| Power Seat: Slide Motor-Full Forward |
Seat slides forward | Power seat control unit/A1, A2, A9, A10 Disconnect power seat control unit connector A (18P). Connect A1 to A10 and A2 to A9; driver's seat should slide forward. |
|
| Power Seat: Slide Motor-Full Backward |
Seat slides backward | Power seat control unit/A1, A2, A9, A10 Disconnect power seat control unit connector A (18P). Connect A1 to A2 and A10 to A9; driver's seat should slide backward. |
|
| Power Seat: Front Up-Down Motor-Full Up |
Front of seat moves up | Power seat control unit/A1, A3, A9, A11 Disconnect power seat control unit connector A (18P). Connect A1 to A11 and A3 to A9; front of driver's seat should move up. |
|
| Power Seat: Front Up-Down Motor-Full Down |
Front of seat moves down | Power seat control unit/A1, A3, A9, A11 Disconnect power seat control unit connector A (18P). Connect A1 to A3 and A11 to A9; front of driver's seat should move down. |
|
| Power Seat: Rear Up-Down Motor-Full Up |
Rear of seat moves up | Power seat control unit/A5, A7, A8, A17 Disconnect power seat control unit connector A (18P). Connect A8 to A7 and A17 to A5; rear of driver's seat should move up. |
|
| Power Seat: Rear Up-Down Motor-Full Down |
Rear of seat moves down | Power seat control unit/A5, A7, A8, A17 Disconnect power seat control unit connector A (18P). Connect A8 to A17 and A7 to A5; rear of driver's seat should move down. |
|
| Power Seat: Recline Motor-Full Forward |
Seat-back moves forward | Power seat control unit/A5, A8, A16, A18 Disconnect power seat control unit connector A (18P). Connect A8 to A18 and A16 to A5; driver's seat back should move forward. |
|
| Power Seat: Recline Motor-Full Backward |
Seat-back moves backward | Power seat control unit/A5, A8, A16, A18 Disconnect power seat control unit connector A (18P). Connect A8 to A16 and A18 to A5; driver's seat back should move backward. |
|