| Air Conditioning |
| Service |
A/C REFRIGERANT SYSTEM, SERVICING
A/C REFRIGERANT R-134A AND REFRIGERANT OIL (PAG), CAPACITIES |
| Torque |
A/C COMPRESSOR - 4-CYL. ENGINE, REMOVING FROM BRACKET (REFRIGERANT PIPES REMAIN CONNECTED)
A/C COMPRESSOR - 6-CYL. ENGINE, REMOVING FROM BRACKET (REFRIGERANT PIPES REMAIN CONNECTED) |
| Axle Nut/Hub Nut |
| Front |
WHEEL BEARING, ASSEMBLY OVERVIEW |
| Rear |
WHEEL BEARING/WHEEL HUB UNIT, REMOVING AND INSTALLING |
| Battery |
BATTERY, TESTING
NO-LOAD VOLTAGE, CHECKING |
| Brakes |
| Bleeding Sequence |
ITT ABS/ESP MARK 20, BLEEDING BRAKE SYSTEM
ITT ABS/ESP MARK 60, BLEEDING BRAKE SYSTEM |
| Disc Brakes |
GENERAL, TECHNICAL DATA |
| Torque |
BRAKES - MECHANICAL COMPONENTS
BRAKES - HYDRAULIC COMPONENTS |
| Charging |
| Generator |
NA |
| Torque |
| 1.8L |
GENERATOR (GEN) - 4-CYLINDER 132KW (180 BHP) ENGINE, REMOVING AND INSTALLING
GENERATOR (GEN) - 4-CYLINDER 165KW (225 BHP) ENGINE, REMOVING AND INSTALLING |
| 3.2L |
GENERATOR (GEN) - 6-CYLINDER 184KW (250 BHP) ENGINE, REMOVING AND INSTALLING |
| Drive Belts |
| Adjustment & Belt Routing |
| 1.8L |
RIBBED BELT, REMOVING AND INSTALLING (ALL ENGINES) |
| 3.2L |
POLY V-BELT, REMOVING AND INSTALLING |
| Engine Cooling |
| General Service Specifications |
| 1.8L |
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM, DRAINING AND FILLING (ALL ENGINES) |
| 3.2L |
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM, DRAINING AND FILLING |
| Radiator Cap Pressure |
1.4-1.6 Bar |
| Thermostat R & I |
| 1.8L |
COOLANT THERMOSTAT, REMOVING, INSTALLING AND CHECKING (AMU & BEA)
COOLANT THERMOSTAT, CHECKING, REMOVING AND INSTALLING (ATC & AWP) |
| 3.2L |
THERMOSTAT HOUSING, REMOVING AND INSTALLING |
| Water Pump R & I |
| 1.8L |
COOLANT PUMP, REMOVING AND INSTALLING (AMU & BEA)
COOLANT PUMP, REMOVING AND INSTALLING (ATC & AWP) |
| 3.2L |
COOLANT PUMP, REMOVING AND INSTALLING |
| Engine Mechanical |
| 1.8L |
| |
|
Compression |
COMPRESSION, CHECKING (AMU & BEA)
]COMPRESSION, CHECKING (ATC & AWP) |
| Oil Pressure |
All Engines:
At Idle & 80°C: 1.0 Bar
At 2000 RPM & 80°C: 3.5 to 4.5 Bar |
| Overhaul |
ENGINE - CRANKSHAFT, CYLINDER BLOCK (AMU & BEA)
ENGINE - CRANKSHAFT, CYLINDER BLOCK (ATC & AWP) |
| Torque |
See Appropriate Procedure |
| 3.2L |
| |
|
Compression |
COMPRESSION, CHECKING |
| Oil Pressure |
At Idle: Min.2.0 Bar
At 2000 RPM: min.3.0 Bar
Max: 7.0 Bar |
| Overhaul |
ENGINE - CRANKSHAFT, CYLINDER BLOCK |
| Torque |
See Appropriate Procedure |
| Fluid Specifications |
See FLUIDS under MAINTENANCE tab. |
| Flywheel/Flex Plate Torque |
60 Nm + 90° |
| Fuel System |
| Pressure Specification |
| 1.8L |
Approx: 2.5 Bar (All Engines) |
| 3.2L |
Approx: 3.5 Bar |
| Fuel Pressure Test Procedure |
| |
1.8L |
SYSTEM PRESSURE, FUEL PRESSURE REGULATOR AND RESIDUAL PRESSURE, CHECKING (ALL ENGINES) |
| |
|
3.2L |
FUEL SYSTEM PRESSURE, PRESSURE REGULATOR AND HOLDING PRESSURE, CHECKING |
| Ignition |
| Firing Order & Cylinder Identification |
| 1.8L |
FIRING ORDER & CYLINDER INDENTIFICATION |
| 3.2L |
FIRING ORDER & CYLINDER INDENTIFICATION |
| Ignition Wires (Resistance) |
Coil-On-Plug |
| Ignition Wires (Routing) |
Coil-On-Plug |
| Spark Plug |
| 1.8L |
TECHNICAL DATA, SPARK PLUGS |
| 3.2L |
TEST DATA, SPARK PLUGS |
| Starting |
| Starter/Torque |
| 1.8L |
STARTER - 4-CYLINDER ENGINE WITH MANUAL TRANSMISSION, REMOVING AND INSTALLING
STARTER - 4-CYLINDER ENGINE WITH AUTOMATIC TRANSMISSION, REMOVING AND INSTALLING |
| 3.2L |
STARTER - 6-CYLINDER ENGINE, REMOVING AND INSTALLING |
| Wheel Alignment |
| Adjustment Specifications |
WHEEL ALIGNMENT SPECIFICATIONS (WITH STANDARD SUSPENSION - G17, G78, G79, G91, G97)
WHEEL ALIGNMENT SPECIFICATIONS (WITH SPORTS SUSPENSION - PQZ, G98) |
| Torque |
| Front |
SUSPENSION STRUT, ASSEMBLY OVERVIEW |
| Rear |
WHEEL BEARING, SERVICING (FWD)
REAR AXLE, SERVICING (AWD) |
| Wheel & Tire |
| Wheel Lug Nut Torque |
120 Nm |