Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions: Notes
WARNING: This page is about a different car, the 2009 Audi S8, 2008 Audi S8, and 2007 Audi S8. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The values of the individual test results must reach the specified value or must be within the min. and max. limits.
NOTE:
- Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between catalytic converter and cylinder head.
- No DTCs in the DTC memory.
- Coolant temperature at least 80 C.
Work procedure
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select the desired "Test-ID".
The current minimum and maximum values will be displayed on the scan tool screen.
| OBDMID (Hex-ID) | Component or System |
|---|---|
| 01 ($01): | Oxygen Sensor Monitor Bank 1 - Sensor 1 |
| 02 ($02): | Oxygen Sensor Monitor Bank 1 - Sensor 2 |
| 05 ($05): | Oxygen Sensor Monitor Bank 2 - Sensor 1 |
| 06 ($06): | Oxygen Sensor Monitor Bank 2 - Sensor 2 |
| 09 ($09): | Oxygen Sensor Monitor Bank 3 - Sensor 1 |
| 10 ($0A): | Oxygen Sensor Monitor Bank 3 - Sensor 2 |
| 13 ($0D): | Oxygen Sensor Monitor Bank 4 - Sensor 1 |
| 14 ($0E): | Oxygen Sensor Monitor Bank 4 - Sensor 2 |
| 33 ($21): | Catalyst Monitor Bank 1 |
| 34 ($22): | Catalyst Monitor Bank 2 |
| 35 ($23): | Catalyst Monitor Bank 3 |
| 36 ($24): | Catalyst Monitor Bank 4 |
| 58 (3A): | EVAP Monitor (0.90) |
| 59 (3B): | EVAP Monitor (0.40) |
| 60 (3C): | EVAP Monitor (0.20) |
| 61 (3D): | Purge Flow Monitor |
| 65 ($41): | Oxygen Sensor Heater Monitor Bank 1 - Sensor 1 |
| 66 ($42): | Oxygen Sensor Heater Monitor Bank 1 - Sensor 2 |
| 69 ($45): | Oxygen Sensor Heater Monitor Bank 2 - Sensor 1 |
| 70 ($46): | Oxygen Sensor Heater Monitor Bank 2 - Sensor 2 |
| 73 ($49): | Oxygen Sensor Heater Monitor Bank 3 - Sensor 1 |
| 74 ($4A): | Oxygen Sensor Heater Monitor Bank 3 - Sensor 2 |
| 77 ($4D): | Oxygen Sensor Heater Monitor Bank 4 - Sensor 1 |
| 78 ($4E): | Oxygen Sensor Heater Monitor Bank 4 - Sensor 2 |
| 113 ($71): | Secondary Air Injection (AIR) System Bank 1 |
| 114 ($72): | Secondary Air Injection (AIR) System Bank 2 |
| 115 ($73): | Secondary Air Injection (AIR) System Bank 3 |
| 116 ($74): | Secondary Air Injection (AIR) System Bank 4 |
| 162 ($A2): | Mis-Fire Cylinder 1 Data |
| 163 ($A3): | Mis-Fire Cylinder 2 Data |
| 164 ($A4): | Mis-Fire Cylinder 3 Data |
| 165 ($A5): | Mis-Fire Cylinder 4 Data |
| 166 ($A6): | Mis-Fire Cylinder 5 Data |
| 167 ($A7): | Mis-Fire Cylinder 6 Data |
| 168 ($A8): | Mis-Fire Cylinder 7 Data |
| 169 ($A9): | Mis-Fire Cylinder 8 Data |
| 170 ($AA): | Mis-Fire Cylinder 9 Data |
| 171 ($AB): | Mis-Fire Cylinder 10 Data |