Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
| Minimum Value | |
|---|---|
| GST manual documentation | 0.3499 |
| Aftermarket scan tool display | 0.35 |
Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.
Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80° C.
Work procedure
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select Mode 6: Check test the results of components that are not continuously monitored.
Select the desired Test-ID..
The current minimum and maximum values will be displayed on the scan tool screen.
The following table is a numerical list of all "Test-IDs" or "Hex-IDs" that may be selected.
Monitor-ID 01 : Oxygen Sensor Monitor Bank 1 - Sensor 1, refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 01 ".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 131 ($83) | P0133 | Response Check. | 0.35 V | --- | Refer to DTC P0133 in the DTC summary table.DTC TABLES . |
| 132 ($84) | P2195 | Oscillation check. | --- | >0.777 V | Refer to DTC P2195 in the DTC summary table.DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID 02 : Oxygen Sensor Monitor Bank 1- Sensor 2
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 02".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 05 ($05) | P0139 | Output Voltage (signal activity) Check. | --- | 700 mSec | Refer to DTC P0139 in the DTC summary table. DTC TABLES . |
| 129 ($81) | P2271 | Output Voltage (signal activity) Check. | 0 V | --- | Refer to DTC P2271 in the DTC summary table. |
| 130 ($82) | P2270 | Output Voltage (signal activity) Check. | --- | 1.2998 V | Refer to DTC P2270 in the DTC summary table. |
| 134 ($86) | P2271 | Output Voltage (signal activity) Check. | -- | 8000 mS | Refer to DTC P2271 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
Monitor-ID 05 : Oxygen Sensor Monitor Bank 2 - Sensor 1, refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 05".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 05 ($05) | P0145 | Output Voltage (signal activity) Check. | --- | 700 mSec | Refer to DTC P0145 in the DTC summary table. DTC TABLES |
| 129 ($81) | P2275 | Output Voltage (signal activity) Check. | 0 V | 1.2998 V | Refer to DTC P2275 in the DTC summary table. |
| 130 ($82) | P2274 | Output Voltage (signal activity) Check. | --- | 1.2998 V | Refer to DTC P2274 in the DTC summary table. |
| 134 ($86) | P2275 | Output Voltage (signal activity) Check. | -- | 10000 mS | Refer to DTC P2275 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
- Test-ID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2, refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 06 ($06)".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 01 ($01) | --- | NO DTC | 708mV | 708mV | |
| 02 ($02) | --- | NO DTC | 708mV | 708mV | |
| 07 ($07) | --- | NO DTC | 1.0 V | 5 V | |
| 08 ($08) | --- | NO DTC | 0 V | 0.00976 V | |
| 129 ($81) | P0159 | Signal activity check. For additional information, refer to the Bosch Motronic MED 9.1 OBD System Strategy. Page 33. | 0.542 V | 5 V | Refer to DTC P0159 in the DTC table DTC TABLES . |
| 130 ($82) | P0159 | Signal activity check. For additional information, refer to the Bosch Motronic MED 9.1 OBD System Strategy. Page 33. | 0 V | 1.039 V | Refer to DTC P0159 in the DTC table DTC TABLES . |
| 131 ($83) | P0159 | Fuel cut off check. For additional information, refer to the Bosch Motronic MED 9.1 OBD System Strategy. Page 33. | 0 V | 200.2 mV | Refer to DTC P0159 in the DTC table DTC TABLES . |
-- If any component or system fails to meet the specified values, Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY
-- Switch the ignition off.
-- Monitor-ID 21: Catalytic Converter Monitoring, Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
-- Select "Monitor-ID 21".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 132 ($84) | P0420 | Catalytic converter monitoring bank 1. | 0.203 | 65535 mSec | Refer to DTC P0420 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Monitor-ID 58 : Fuel Tank EVAP System Integrity/Leak Test (0.90"). Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 58 ".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0455 | Tank leak test: Large leak. | 0.95 Sec | 65535 mSec | Refer to DTC P0455 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 59 : Fuel Tank EVAP System Integrity/Leak Test (0.40/1.0mm). Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 59".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0442 | Fuel Tank Leak Test: Small leak. | 1550 mSec | 65535 mSec | Refer to DTC P0442 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 60 : Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5mm). Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 60".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0456 | Tank leak test: Pinhole leak (0.5 mm). | 4.5 Sec | 65535 mSec | Refer to DTC P0456 in the DTC summary table. DTC TABLES . |
| 130 ($82) | Fuel Tank Leak Test. | 4.9 Sec | 65535 mSec |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 61 : Tank Vent Valve function check. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 61".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 128 ($80) | P0441 | Tank vent valve check from % DTEV: Active test Air balance at idle OK, (Normal operation and short test 70). | 0.350 % | 1.999 | Refer to DTC P0441 in the DTC summary table. DTC TABLES . |
| 130 ($82) | --- | Tank vent valve check from %DTEV: Active test, Oxygen sensor regulator deviating in lean direction (can only test OK), (Normal operation and short test 70). | 0.07 | 10 | --- |
| 130 ($82) | --- | Tank vent valve check from %DTEV: Active test, Oxygen sensor regulator deviation in rich direction (can only test OK), (Normal operation and short test 70). | -10 | -0.07 | --- |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 65 : Oxygen Sensor Heater Monitor Bank 1 - Sensor 1. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 65".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 133 ($85) | P0135 | Oxygen sensor heating in front of catalytic converter, diagnosis, Bank 1 (Constant oxygen sensor monitoring with CJI25). Ceramic temperature monitoring. | + 40° C | 1200 °C | Refer to DTC P0135 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 66".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0141 | Oxygen sensor heating behind catalytic converter, diagnosis, Bank 1 Nernst cell internal resistance test. | 0 Ω | 1404 Ω | Refer to DTC P0141 in the DTC summary table. DTC TABLES . |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID 69 : Oxygen Sensor Heater Monitor Bank 2 - Sensor 1. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID 69".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0147 | Diagnosis of Sensor 1 | 0 Ω | 1056... 11856 Ω | Refer to DTC P0147 in the DTC summary table. |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 70 ($46)".
-- Select the desired "Test-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min. | Max. | Additional Information |
|---|---|---|---|---|---|
| 129 ($81) | P0161 | Readiness Check. | 0 Ω | 43320 Ω | Refer to DTC P0161 in the DTC table. |
-- If any component or system fails to meet the specified values, Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY
-- Switch the ignition off.
-- Monitor-ID A2 : Mis-Fire Cylinder 1 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A2".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0301 | Misfire cylinder 1, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0301 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0301 | Misfire cylinder 1, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0301 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID A3: Mis-Fire Cylinder 2 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6 Check test the results of components that are not continuously monitored".
Select "Monitor-ID A3:".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0302 | Misfire cylinder 2, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0302 | Misfire cylinder 2, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0302 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID A4: Mis-Fire Cylinder 3 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A4".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0303 | Misfire cylinder 3, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0303 | Misfire cylinder 3, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0303 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- Monitor-ID A5 : Mis-Fire Cylinder 4 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A5".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0304 | Misfire cylinder 4, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0304 | Misfire cylinder 4, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0304 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition off.
-- Monitor-ID A6 : Mis-Fire Cylinder 5 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A6".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0305 | Misfire cylinder 5, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0305 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0305 | Misfire cylinder 5, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0305 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition off.
-- Monitor-ID A7 : Mis-Fire Cylinder 6 Data. Refer to DIAGNOSTIC MODE 06 - READ TEST RESULTS FOR SPECIFIC DIAGNOSTIC FUNCTIONS .
-- Connect the scan tool.
-- Start the engine and run at idle.
-- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor-ID A7".
-- Select the desired "Test-ID (TID)" or "Hex-ID".
-- Check specified values at idle.
| Test-ID (TID) (Hex-ID) | DTC | Component or System | Min./Max. Values | Additional Information | |
|---|---|---|---|---|---|
| 11 ($0B) | P0306 | Misfire cylinder 6, Average value over 10 Driving Cycles. | 0 - 65535 (counts) | Refer to DTC P0306 in the DTC summary table. DTC TABLES . | |
| 12 ($0C) | P0306 | Misfire cylinder 6, in this Driving Cycle. | 0 - 65535 (counts) | Refer to DTC P0306 in the DTC summary table. DTC TABLES . | |
-- If any of components or systems fail to meet the specified values. Refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC or the corresponding diagnostic repair procedure DIAGNOSTIC MODE 03 - READ DTC MEMORY .
-- Switch the ignition off.
-- If any of the components or systems fail to meet the specified values, refer to Diagnostic Mode 03: Interrogating Fault Memory to check for stored DTCs or the corresponding diagnostic repair procedure.
-- Switch the ignition off.