Specifications Index

SPECIFICATIONS INDEX

System			Specification/Procedure
Air Conditioning
Service			REFRIGERANT R134A PHYSICAL DATA
Torque			FASTENER TIGHTENING SPECIFICATIONS
Axle Nut/Hub Nut
Front			200 Nm +180°
Rear			200 Nm +180°
Battery			COLD CRANK AMPS TABLE
Brakes
Bleeding Sequence			HYDRAULIC SYSTEM, BLEEDING
Disc Brakes			Brakes Technical Data
Torque			FASTENER TIGHTENING SPECIFICATIONS Mechanical Components FASTENER TIGHTENING SPECIFICATIONS Hydraulic Components
Charging
Generator			GENERATOR
Torque			N/A
Drive Belts
Adjustment
3.0L			RIBBED BELT, REMOVING AND INSTALLING
4.0L			Ribbed Belt, Removing And Installing
	4.2L		Ribbed Belt, Removing And Installing
	6.3L		Ribbed Belt, Removing And Installing
Belt Routing
		3.0L	See fig. 11 under Installing
	4.0L		See fig. 5 under Installing
	4.2L		See fig. 4 under Installing
	6.3L		See fig. 6 under Installing Vehicles through MY 2013: See fig. 7 under Installing Vehicles from MY 2014:
Engine Cooling
General Service Specifications			Refer to the approrpiate FLUID CAPACITY TABLES information.
Radiator Cap Pressure			1.4 to 1.6 bar (20.30 to 23.20 psi)
Thermostat R & I
3.0L			COOLANT THERMOSTAT, REMOVING AND INSTALLING
	4.0L		Map Controlled Engine Cooling Thermostat -F265-, Removing And Installing
	4.2L		Map Controlled Engine Cooling Thermostat -F265-, REMOVING AND INSTALLING
	6.3L		Coolant Thermostat, Removing And Installing
Water Pump R & I
3.0L			COOLANT PUMP, REMOVING AND INSTALLING
	4.0L		Coolant Pump, Removing And Installing
	4.2L		COOLANT PUMP, REMOVING AND INSTALLING
	6.3L		Coolant Pump, Removing And Installing
Engine Mechanical
3.0L
		Compression	Compression Pressure, Checking
Oil Pressure			Engine Code(s): CPNA and CPNB Oil pressure when the vehicle is idling: minimum 0.8 bar (11.6 psi) Oil pressure at 2, 000 RPM: minimum 1.5 bar (21.7 psi). Engine Code: CTUB Oil pressure when the vehicle is idling is minimum 1.2 bar (17.4). Oil pressure at 2, 000 RPM is minimum 1.5 bar (21.7 psi).
Overhaul			10 ENGINE ASSEMBLY Engine Code: CPNA 10 ENGINE ASSEMBLY Engine Code: CTUB
Torque			Fastener Tightening Specifications Engine Code: CTUB
4.0L
		Compression	Compression Pressure, Checking Engine Code(s): CEUA, CGTA, CTFA and CTGA
Oil Pressure			Oil pressure at idle: minimum 1.3 ± 0.3 bar (18.9 ± 4.4 PSI) Oil pressure at 2, 000 RPM: minimum 1.6 to 2.2 bar (23.2 to 31.9 PSI)
Overhaul			10 ENGINE ASSEMBLY
Torque			Engine, Installing
4.2L
		Compression	Compression Pressure, Checking
Oil Pressure			Oil pressure when the vehicle is idling: minimum 1.3 bar (18.85 psi) Oil pressure at 2, 000 RPM: minimum 1.9 bar (27.55 psi)
Overhaul			10 ENGINE ASSEMBLY
Torque			FASTENER TIGHTENING SPECIFICATIONS
6.3L
	Compression		Compression Pressure, Checking
	Oil Pressure		Oil pressure when the vehicle is idling: minimum 0.8 bar (11.6 psi) Oil pressure at 3, 000 RPM is minimum 3 bar (43 psi).
	Overhaul		10 ENGINE ASSEMBLY
	Torque		Fastener Tightening Specifications
Fluid Specifications			See FLUIDS under MAINTENANCE tab.
Engine Oil Pan Drain Plug			30 Nm
Flywheel/Flex Plate Torque			60 Nm + 90°
Fuel System
Pressure Specification
3.0L			Engine Code: CTUB The fuel injection system is separated into a high-pressure section (maximum approximately 120 bar) and a low-pressure section (approximately 7 bar).
4.0L			Engine Code(s): CEUA and CGTA The fuel injection system is separated into a high-pressure section (maximum approximately 140 bar) and a low-pressure section (4 to 7 bar).
4.2L			Engine Code: CDRA The fuel injection system is separated into a high-pressure section (max. approximately 140 bar) and a low-pressure section (approximately 7 bar).
	6.3L		N/A
Fuel Pressure Test Procedure
	3.0L		Fuel Pressure Sensor -G247-, CHECKING Engine Code(s): CPNA & CPNB FUEL PRESSURE TEST Engine Code(s): CTUB
	4.0L		Fuel Pressure Sensor -G247-, CHECKING Fuel Pressure Sensor 2 -G624-, CHECKING
		4.2L	Fuel Pressure Test
	6.3L		Fuel Pressure Sensor -G247-, Checking Fuel Pressure Sensor 2 -G624-, Checking
Ignition
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)			Coil-On-Plug
Ignition Wires (Routing)			Coil-On-Plug
Spark Plug
3.0L			Test Data And Spark Plugs Engine Code(s): CTUB
4.0L			Test Data And Spark Plugs Engine Code(s): CEUA, CGTA, CTFA and CTGA
4.2L			TEST DATA AND SPARK PLUGS
	6.3L		Test Data And Spark Plugs
Starting
Starter			N/A
Torque			N/A
Wheel Alignment
Adjustment Specifications			WHEEL ALIGNMENT SPECIFIED VALUES
Torque			Fastener Tightening Specifications Front Suspension FASTENER TIGHTENING SPECIFICATIONS Rear Suspension
Wheel & Tire
Wheel Lug Nut Torque			140 Nm