Diagnostic Mode 06 - Read Test Results For Specific Diagnostic Functions (My-2015): Notes
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 06 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
| Minimum Value | |
|---|---|
| GST information documentation | 0.3499 |
| Aftermarket scan tool display | 0.35 |
Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.
Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80° C.
Work procedure
-- Connect the scan tool.
-- Start the engine and let run at idle speed.
-- Select Mode 6: Check test the results of components that are not continuously monitored.
Select the desired Test-ID..
The current minimum and maximum values will be displayed on the scan tool screen.
The following table is a numerical list of all "Hex-IDs" that may be selected.
| Hex-ID | Component or System |
|---|---|
| $00: | Supported OBDMID `s ($ 01 - $ 20) |
| $01: Monitor-ID ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1 | Oxygen Sensor Monitor Bank 1 - Sensor 1 |
| $02: Monitor-ID ($02): Oxygen Sensor Monitor Bank 1- Sensor 2 | Oxygen Sensor Monitor Bank 1- Sensor 2 |
| $05: Monitor-ID ($05): Oxygen Sensor Monitor Bank 2- Sensor 1 | Oxygen Sensor Monitor Bank 2- Sensor 1 |
| $06: Monitor-ID ($06): Oxygen Sensor Monitor Bank 2- Sensor 2 | Oxygen Sensor Monitor Bank 2- Sensor 2 |
| $20: | Supported OBDMID `s ($ 21 - $ 40) |
| $21: Monitor-ID ($21): Catalyst monitoring bank 1 | Catalytic Converter Monitoring Bank 1 |
| $22: Monitor-ID ($22): Catalyst monitoring bank 2 | Catalytic Converter Monitoring Bank 2 |
| $35: Monitor-ID ($35): Cam Shaft Adjustment IVVT diagnosis bank 1 | Cam shaft adjustment / IVVT diagnosis bank 1 |
| $36: Monitor-ID ($36): Cam Shaft Adjustment IVVT diagnosis bank 2 | Cam shaft adjustment / IVVT diagnosis bank 2 |
| $3C: Monitor-ID ($3C): Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5mm) | Fuel Tank EVAP System Integrity / Leak Test (0.20" / 0.5mm) |
| $3D: Monitor-ID ($3D): EVAP Valve Function Check | EVAP Valve Function Check |
| $40: | Supported OBDMID's ($41 - $5F) |
| $41: Monitor-ID ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1 | Oxygen Sensor Heater Monitor Bank 1 - Sensor 1 |
| $42: Monitor-ID ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2 | Oxygen Sensor Heater Monitor Bank 1 - Sensor 2 |
| $45: Monitor-ID ($45): Oxygen Sensor Heater Monitor Bank 2- Sensor 1 | Oxygen Sensor Heater Monitor Bank 2- Sensor 1 |
| $46: Monitor-ID ($46): Oxygen Sensor Heater Monitor Bank 2- Sensor 2 | Oxygen Sensor Heater Monitor Bank 2- Sensor 2 |
| $60: | Supported OBDMID's ($61 - $80) |
| $71: Monitor-ID ($71): secondary air system (Bank 1) | Secondary air system 1 (bank 1) |
| $72: Monitor-ID ($72): secondary air system (Bank 2) | Secondary air system 2 (bank 2) |
| $80: | Supported OBDMID's ($81 - $A0) |
| $90: | Supported OBDMID's ($A1 - $C0) |
| $A2: Monitor-ID ($A2) : Mis-Fire Cylinder 1 Data | Mis-Fire Cylinder 1 Data |
| $A3: Monitor-ID $A3: Mis-Fire Cylinder 2 Data | Mis-Fire Cylinder 2 Data |
| $A4: Monitor-ID $A4: Mis-Fire Cylinder 3 Data | Mis-Fire Cylinder 3 Data |
| $A5: Monitor-ID $A5 : Mis-Fire Cylinder 4 Data | Mis-Fire Cylinder 4 Data |
| $A6: Monitor-ID $A6 : Mis-Fire Cylinder 5 Data | Mis-Fire Cylinder 5 Data |
| $A7: Monitor-ID $A7 : Mis-Fire Cylinder 6 Data | Mis-Fire Cylinder 6 Data |
| $A8: Monitor-ID $A8 : Mis-Fire Cylinder 7 Data | Mis-Fire Cylinder 7 Data |
| $A9: Monitor-ID $A9 : Mis-Fire Cylinder 8 Data | Mis-Fire Cylinder 8 Data |