Transmission Control Module --, 7 SPEED DL-382-7F (2016 MY)

DL-382-7F
DTC	Fault Code Description	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters with Enable Conditions	Monitoring Time Length	Frequency of checks, MIL Illum
P0501	Vehicle Speed Sensor "A" Circuit Range/Performance	Rationality check	Difference between measured and calculated output speed for shaft 1 And Difference between output shaft speed 1 and shaft 2	>150 rpm And >150 rpm	Input shaft speeds for shafts 1 and 2 >100 rpm	2.0 s	2 DCY Continuous
P0560	System Voltage	Signal range check	Internal sensor supply voltage	> 5.5 V Or < 4.5 V		2.0 s	2 DCY Continuous
P0562	System Voltage Low	Signal range check	Voltage And One of the following monitors is in protective function P0750, P0765, P0760, P0755, P0745, P0775, P0795, P0770, P2706	< 8 V		5.0 s	2 DCY Continuous
P062F	Internal Control Module EEPROM Error	Rationality check	Comparison of EEProm date - both copies Comparison of stored value - both copies Write ability check	Invalid Faulty	When reading a datablock active	2.0 s	2 DCY Continuous
P0602	Control Module Programming Error	Rationality check	The Control Module-SW is	Incompatible		2.0 s	2 DCY Continuous
P0604	Internal Control Module Random Access Memory (RAM) Error	Functional check	Write ability check	Faulty		2.0 s	2 DCY Continuous
P0607	Control Module Performance	Functional check	Too low gear selected and clutch closed Too low gear selected Two gears on one shaft Both clutches closed Incorrect clutch actuation Delayed traction			2.0 s	2 DCY Continuous
P0614	ECM/TCM Incompatible	Rationality check	Information of transmission code is faulty Information of engine code is faulty		Ignition on	2.0 s	2 DCY Continuous
P0666	TCM Temperature Sensor	Circuit continuity check	TCM Temperature Sensor self check TCM Temperature Sensor TCM Temperature Sensor at And Actual chip temperature Or Actual chip temperature	Failed invalid state -0.03125° C And < -24° C Or > 24° C	Ignition on TCM Temperature Sensor Initialization finished	2.0 s	2 DCY Continuous
P0667	TCM Temperature Sensor	Rationality check	Difference between TCM Temperature Sensor and internal chip temperature Difference between actual TCM Temperature Sensor and filtered temperature	26 > x > -26° C > 8° C	Ignition on TCM Temperature Sensor Initialization finished	2.0 s	2 DCY Continuous
P06A6	Sensor Reference Voltage "A" Circuit Range/Performance	Circuit continuity check	Voltage	2.0 V		2.0 s	2 DCY Continuous
P06A7	Sensor Reference Voltage "B" Circuit Range/Performance	Circuit continuity check	Voltage	2.0 V		2.0 s	2 DCY Continuous
P06A8	Sensor Reference Voltage "C" Circuit Range/Performance	Circuit continuity check	Voltage	2.0 V		2.0 s	2 DCY Continuous
P06A9	Sensor Reference Voltage "D" Circuit Range/Performance	Signal range check	Internal sensor supply voltage	> 6.5 V or < 5.5 V		2.0 s	2 DCY Continuous
P0700	Transmission Control System Malfunction	Functional check	CPU permanent shutdown of all actors	Active		2.0 s	2 DCY Continuous
P0702	Transmission Control System Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0716	Input/Turbine Shaft Speed Sensor "A" Circuit Range/Performance	Signal range check	Input shaft speed for shaft 1	> 12, 000 rpm		2.0 s	2 DCY Continuous
P0718	Input/Turbine Shaft Speed Sensor "A" Circuit Intermittent	Rationality check	No signal	> 1.0 s	Ignition on	2.0 s	2 DCY Continuous
P0745	Pressure Control Solenoid "A"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0748	Pressure Control Solenoid "A" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0750	Shift Solenoid "A"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0753	Shift Solenoid "A" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0755	Shift Solenoid "B"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0758	Shift Solenoid "B" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0760	Shift Solenoid "C"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0763	Shift Solenoid "C" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0765	Shift Solenoid "D"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0768	Shift Solenoid "D" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0770	Shift Solenoid "E"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0773	Shift Solenoid "E" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0775	Pressure Control Solenoid "B"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0778	Pressure Control Solenoid "B" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0795	Pressure Control Solenoid "C"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P0798	Pressure Control Solenoid "C" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P0811	Excessive Clutch "A" Slippage	Rationality check	Clutch slippage was detected	>150 rpm	Clutch state is Drive	2.0 s	2 DCY Continuous
P081E	Excessive Clutch "B" Slippage	Rationality check	Clutch slippage was detected	>150 rpm	Clutch state is Drive	2.0 s	2 DCY Continuous
P0B0A	Auxiliary Transmission Fluid Pump Motor Supply Voltage Circuit Low	Signal range check	Voltage And P0B0D is in protective function	< 10.0 V		2.0 s	2 DCY Continuous
P0B0D	Electric / Auxiliary Transmission Fluid Pump Motor Control Module	Signal range check	Difference between actual and commanded ATF pump speed	>500 rpm	Calibration not active	2.0 s	2 DCY Continuous
P0C28	Electric / Auxiliary Transmission Fluid Pump "A" Motor Current High	Functional check	ATF pump overcurrent protection	Active		2.0 s	2 DCY Continuous
P0C29	Electric / Auxiliary Transmission Fluid Pump "A" Driver Circuit Performance	Circuit continuity check	Electrical failure in power amplifier Driver error Overload ATF pump			2.0 s	2 DCY Continuous
P0C2A	Electric / Auxiliary Transmission Fluid Pump "A" Motor Stalled	Functional check	Current ATF pump speed < And Set current for ATF pump control	300 rpm And 30-50 A	ATF pump governor enabled And Target ATF-engine speed > 300 rpm	2.0 s	2 DCY Continuous
P0C2C	Electric / Auxiliary Transmission Fluid Pump Control Module Feedback Signal Range/Performance	Rationality check	Sensor output sin² +cos²	>0.8 or <1.2	Sensor supply voltage 4.5 - 5.5 V	2.0 s	2 DCY Continuous
P0C2D	Electric / Auxiliary Transmission Fluid Pump Control Module Feedback Signal Low	Signal range check	Sensor output voltage	< 0.25 V	Sensor supply voltage 4.5 - 5.5 V	2.0 s	2 DCY Continuous
P0C2E	Electric / Auxiliary Transmission Fluid Pump Control Module Feedback Signal High	Signal range check	Sensor output voltage	> 4.5 V	Sensor supply voltage 4.5 - 5.5 V	2.0 s	2 DCY Continuous
P187A	Gear selector 1 Engaging process not successful	Functional check	Timeout in gear actuator state after syncronization Timeout in gear actuator state Unlatched Timeout in gear actuator state Engage	> 1.0 s	Gear actuator 1-3 nominal state is after syncronization Gear actuator 1-3 nominal state is Unlatched Gear actuator 1-3 nominal state is Engage	2.0 s	2 DCY Continuous
			Timeout in gear actuator state Synchronize	> 2.0 s	Gear actuator 1-3 nominal state is Synchronize
			Difference between measured and synchronize shaft speed 1 And Gear actuator 1-3 movement	> 300 rpm And > 7mm or < -7mm	Shaft 1 and 2 in sync position
P187B	Gear selector 2 Engaging process not successful	Functional check	Timeout in gear actuator state after syncronization Timeout in gear actuator state Unlatched Timeout in gear actuator state Engage	> 1.0 s	Gear actuator 2-R nominal state is after syncronization Gear actuator 2-R nominal state is Unlatched Gear actuator 2-R nominal state is Engage	2.0 s	2 DCY Continuous
			Timeout in gear actuator state Synchronise	> 2.0 s	Gear actuator 2-R nominal state is Synchronise
			Difference between measured and synchronize shaft speed 2 Aand Gear actuator 2-R movement	> 300 rpm And > 7mm or < -7mm	Shaft 1 and 2 in sync position
P187C	Gear selector 3 Engaging process not successful	Functional check	Timeout in gear actuator state after syncronization Timeout in gear actuator state Unlatched Timeout in gear actuator state Engage	> 1.0 s	Gear actuator 5-7 nominal state is after syncronization Gear actuator 5-7 nominal state is Unlatched Gear actuator 5-7 nominal state is Engage	2.0 s	2 DCY Continuous
			Timeout in gear actuator state Synchronise	> 2.0 s	Gear actuator 5-7 nominal state is Synchronise
			Difference between measured and synchronize shaft speed 1 And Gear actuator 5-7 movement	> 300 rpm And > 7mm or < -7mm	Shaft 1 and 2 in sync position
P187D	Gear selector 4 Engaging process not successful	Functional check	Timeout in gear actuator state after syncronization Timeout in gear actuator state Unlatched Timeout in gear actuator state Engage	> 1.0 s	Gear actuator 4-6 nominal state is after syncronization Gear actuator 4-6 nominal state is Unlatched Gear actuator 4-6 nominal state is Engage	2.0 s	2 DCY Continuous
			Timeout in gear actuator state Synchronise	> 2.0 s	Gear actuator 4-6 nominal state is Synchronise
			Difference between measured and synchronize shaft speed 2 And Gear actuator 4-6 movement	> 300 rpm And > 7mm or < -7mm	Shaft 1 and 2 in sync position
P2159	Vehicle Speed Sensor "B" Circuit Range/Performance	Rationality check	Difference between measured and calculated output speed for shaft 2 And Difference between output shaft speed 1 and shaft 2	>150 rpm And >150 rpm	Input shaft speeds for shafts 1 and 2 >100 rpm	2.0 s	2 DCY Continuous
P2162	Vehicle Speed Sensor "A"/"B" Correlation	Rationality check	Difference between output shaft speeds and input speeds shafts 1 and 2	>150 rpm	Input shaft speeds for shafts 1 and 2 >100 rpm and engaged gear position is not neutral	2.0 s	2 DCY Continuous
P2706	Shift Solenoid "F"	Circuit continuity check	Difference between set current and measured current.	> 100mA		2.0 s	2 DCY Continuous
P2709	Shift Solenoid "F" Electrical	Circuit continuity check	Internal voltage	Failure		2.0 s	2 DCY Continuous
P2766	Input/Turbine Shaft Speed Sensor "B" Circuit Range/Performance	Signal range check	Input shaft speed for shaft 2	> 12, 000 rpm		2.0 s	2 DCY Continuous
P2768	Input/Turbine Shaft Speed Sensor "B" Circuit Intermittent	Rationality check	No signal	> 1.0 s	Ignition on	2.0 s	2 DCY Continuous
P283B	Shift Fork "C" Position Circuit	Signal range check	No signal	> 1.0 s		2.0 s	2 DCY Continuous
P283C	Shift Fork "C" Position Circuit Range/Performance	Signal range check	Duty-Cycle Position sensor Time of oscillation	>92.5 % <7.5 % < 0.9 ms > 1.1 ms	Sensor supply voltage between 4.5-5.5 V	2.0 s	2 DCY Continuous
P284A	Shift Fork "B" Stuck	Functional check	Timeout in gear actuator state Disengage	> 2.0 s	Gear actuator 2-R nominal state is Disengage	2.0 s	2 DCY Continuous
P284B	Shift Fork "C" Stuck	Functional check	Timeout in gear actuator state Disengage	> 2.0 s	Gear actuator 5-7 nominal state is Disengage	2.0 s	2 DCY Continuous
P284C	Shift Fork "D" Stuck	Functional check	Timeout in gear actuator state Disengage	> 2.0 s	Gear actuator 4-6 nominal state is Disengage	2.0 s	2 DCY Continuous
P284D	Shift Fork "A" Unrequested Movement	Functional check	Loaded gear leaves the engage-position Gear actuator 1-3 leaves the engage-position	> 3 mm > 1.0 s	Gear actuator 1 - 3 nominal state is engaged	2.0 s	2 DCY Continuous
P284E	Shift Fork "B" Unrequested Movement	Functional check	Loaded gear leaves the engage-position Gear actuator 2-R leaves the engage-position	> 3 mm > 1.0 s	Gear actuator 2 - R nominal state is engaged	2.0 s	2 DCY Continuous
P284F	Shift Fork "C" Unrequested Movement	Functional check	Loaded gear leaves the engage-position Gear actuator 5-7 leaves the engage-position	> 3 mm > 1.0 s	Gear actuator 5 - 7 nominal state is engaged	2.0 s	2 DCY Continuous
P2831	Shift Fork "A" Position Circuit	Signal range check	No signal	> 1.0 s		2.0 s	2 DCY Continuous
P2832	Shift Fork "A" Position Circuit Range/Performance	Signal range check	Duty-Cycle Position sensor Time of oscillation	>92.5 % <7.5 % < 0.9 ms > 1.1 ms	Sensor supply voltage between 4.5-5.5 V	2.0 s	2 DCY Continuous
P2836	Shift Fork "B" Position Circuit	Signal range check	No signal	> 1.0 s		2.0 s	2 DCY Continuous
P2837	Shift Fork "B" Position Circuit Range/Performance	Signal range check	Duty-Cycle Position sensor Time of oscillation	>92.5 % <7.5 % < 0.9 ms > 1.1 ms	Sensor supply voltage between 4.5-5.5 V	2.0 s	2 DCY Continuous
P2840	Shift Fork "D" Position Circuit	Signal range check	No signal	> 1.0 s		2.0 s	2 DCY Continuous
P2841	Shift Fork "D" Position Circuit Range/Performance	Signal range check	Duty-Cycle Position sensor Time of oscillation	>92.5 % <7.5 % < 0.9 ms > 1.1 ms	Sensor supply voltage between 4.5-5.5 V	2.0 s	2 DCY Continuous
P2845	Shift Fork "A" Position Sensor Incorrect Neutral Position Indicated	Functional check	Gear actuator 1-3 leaves the neutral-position	> 3 mm	Gear actuator 1-3 nominal state is Neutral	2.0 s	2 DCY Continuous
P2846	Shift Fork "B" Position Sensor Incorrect Neutral Position Indicated	Functional check	Gear actuator 2-R leaves the neutral-position	> 3 mm	Gear actuator 2-R nominal state is Neutral	2.0 s	2 DCY Continuous
P2847	Shift Fork "C" Position Sensor Incorrect Neutral Position Indicated	Functional check	Gear actuator 5-7 leaves the neutral-position	> 3 mm	Gear actuator 5-7 nominal state is Neutral	2.0 s	2 DCY Continuous
P2848	Shift Fork "D" Position Sensor Incorrect Neutral Position Indicated	Functional check	Gear actuator 4-6 leaves the neutral-position	> 3 mm	Gear actuator 4-6 nominal state is Neutral	2.0 s	2 DCY Continuous
P2849	Shift Fork "A" Stuck	Functional check	Timeout in gear actuator state Disengage	> 2.0 s	Gear actuator 1-3 nominal state is Disengage	2.0 s	2 DCY Continuous
P2850	Shift Fork "D" Unrequested Movement	Functional check	Loaded gear leaves the engage-position Gear actuator 4-6 leaves the engage-position	> 3 mm > 1.0 s	Gear actuator 4 - 6 nominal state is engaged	2.0 s	2 DCY Continuous
U0001	High Speed CAN Communication Bus	Communication check	Detects CAN Bus off		Ignition on	2.0 s	2 DCY Continuous
U0002	High Speed CAN Communication Bus Performance	Communication check	No messages received from other control units		Ignition on	2.0 s	2 DCY Continuous
U0100	Lost Communication With ECM/PCM "A"	Communication check	Engine Control Module	No signal	Ignition on	2.0 s	2 DCY Continuous
U0121	Lost Communication With Anti-Lock Brake System (ABS) Control Module	Communication check	Anti-Lock Brake System	No signal	Ignition on	2.0 s	2 DCY Continuous
U0401	Invalid Data Received From ECM/PCM "A"	Communication check	Invalid data received from Engine Control Module		Ignition on	2.0 s	2 DCY Continuous
U0415	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module	Communication check	Invalid data received from Anti-Lock Brake System		Ignition on	2.0 s	2 DCY Continuous