Battery Energy Control Module --, 2021 MY

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
Battery Energy Control Module (BECM) - Hardware/Internal Malfunctions
BECM: Performance (Self Test)	P0A1F	internal hardware check	CPU test	failed				5 [ms] On Mode Change (except to EMERGENCY_OFF or LOCAL_ACTIVE)	0 DCY
			OR
			RAM test	failed
			OR
			ROM test	failed
BECM: Internal Control Module	P0604	Random Access Memory (RAM) check	secured internal data exchange	failed				5 [ms] continuous	0 DCY
BECM: Internal Control Module	P062F	EEPROM check	memory checksum error	detected				1 [s] multiple	0 DCY
BECM: Hybrid CAN Controller	P163E	CAN RAM check	read/write check in hybrid CAN-RAM	failed		BECM mode	= INIT	5 [ms] once / DCY	0 DCY
BECM: Battery CAN Controller	P163E	CAN RAM check	read/write check in battery CAN-RAM	failed		BECM mode	= INIT	5 [ms] once / DCY	0 DCY
BECM: Control Module Processor	P0606	watchdog reset	watchdog reset	occurred				5 [ms] continuous	0 DCY
BECM: Control Module	U3001	improper shutdown performance	incorrect BECM postrun execution (aborted or not started)	5 times in a row		BECM mode	= INIT	150 [ms] once / DCY	0 DCY
BECM: Control Module	U3001	improper shutdown performance	at least one OBD-relevant monitoring	failed and pending		BECM mode	= INIT	150 [ms] once / DCY	0 DCY
BECM: Battery Monitor Module - Daisy Chain Input	P058D	voltage monitoring performance (short to battery)	CASE 1:			(BECM mode	= AC_CHARGING	2 [s] continuous	0 DCY
			ratio of BECM Daisy Chain input voltage to battery voltage	> 0.9	[-]		OR
						BECM mode	= EMERGENCY_OFF
			CASE 2:				OR
			BECM Daisy Chain input voltage	> 4	[V]	BECM mode	= HV_OFF
			Critical over voltage/under voltage condition of any cell voltage	reported			OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						Battery CAN communication	active
						error memory status flags of all CMCs	valid
BECM: Battery Monitor Module - Daisy Chain Input	P058D	voltage monitoring performance (short to ground)	BECM Daisy Chain input voltage	< 4	[V]	(BECM mode	= AC_CHARGING	2 [s] continuous	0 DCY
			No Critical over voltage/under voltage condition of any cell voltage	reported			OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						Battery CAN communication	active
						error memory status flags of all CMCs	valid
BECM: Battery Monitor Module - Daisy Chain Output	P058D	voltage monitoring performance (short to battery)	BECM Daisy Chain output voltage	> 4	[V]	(BECM mode	= AC_CHARGING	5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						BECM Daisy Chain output target value	= 0
BECM: Battery Monitor Module - Daisy Chain Output	P058D	voltage monitoring performance (short to ground)	BECM Daisy Chain output voltage	< 4	[V]	(BECM mode	= AC_CHARGING	5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						BECM Daisy Chain output target value	= 1
BECM: Internal Control Module - Hardware Disable Output	P0E2D	hybrid/EV battery monitor performance (short to battery)	Hardware-Disable output voltage	> 10	[V]	(BECM mode	= AC_CHARGING	5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						BECM HW Disable output target value	= 0
BECM: Internal Control Module - Hardware Disable Output	P0E2D	hybrid/EV battery monitor performance (short to ground)	Hardware-Disable output voltage	< 4	[V]	(BECM mode	= AC_CHARGING	5 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
						BECM HW Disable output target value	= 1
BECM: High-Voltage System Interlock	P0A0D	circuit "A" high (short to battery)	voltage drop across shunt	> 5	[V]				500 [ms] continuous	0 DCY
BECM: High-Voltage System Interlock	P0A0C	circuit "A" low (short to ground)	voltage drop across shunt	< 0.2	[V]				500 [ms] continuous	0 DCY
BECM: High-Voltage System Interlock	P0A0A	HV interlock implausible	HV interlock loop current	< 8	[mA]				100 [ms] continuous	0 DCY
			OR
			HV interlock loop current	> 12	[mA]
BECM: High-Voltage System Interlock	P0A0B	performance (internal circuit)	Value measured by HV interlock ADC with input signal set to ground level (0 V)	> 51.57	[mV]	(BECM mode	= AC_CHARGING		500 [ms] continuous	0 DCY
			OR				OR
			Value measured by HV interlock ADC with input signal set to reference voltage (3.3 V)	<3248.43	[mV]	BECM mode	= EMERGENCY_OFF
			OR				OR
			HV Interlock ADC values	not received		BECM mode	= HV_OFF
			for time	10	[ms]		OR
						BECM mode	= HV_ON
							OR
						BECM mode)	= INIT
BECM: Control Module Power Off Timer	P262B	plausibility check A - MAX check (rationality check high)	CASE 1:			BECM mode	= RUN_ON	[s]	0 [s] once / DCY	2 DCY
			0.06 * actual postrun timer	≤ 1	[s]	HV Supply	switched off
			AND			for time	≥ 5
			actual postrun timer - HV off hardware timer value	≥ 1	[s]
			CASE 2:
			0.06 * actual postrun timer	> 1	[s]
			AND
			ratio of HV off hardware timer value to actual postrun time	≥ 1.06	[-]
BECM: Control Module Power Off Timer	P262B	plausibility check A - MIN check (rationality check low)	CASE 1:			BECM mode	= RUN_ON	[s]	0 [s] once / DCY	2 DCY
			0.06 * actual postrun timer	≤ 1	[s]	HV Supply	switched off
			AND			for time	≥ 5
			HV off hardware timer value - actual postrun timer	≥ 1	[s]
			CASE 2:
			0.06 * actual postrun timer	> 1	[s]
			AND
			ratio of HV off hardware timer value to actual postrun time	≤ 0.94	[-]
BECM: Control Module Power Off Timer	P262B	plausibility check B - MIN check (rationality check low)	ratio of HV off hardware timer value to last stored internal postrun time	≤ 0.94	[-]	BECM mode	= INIT		0 [s] once / DCY	2 DCY
BECM: Control Module Power Off Timer	P262B	plausibility check C (internal circuit)	Response from HV Off Hardware Timer circuit during initialization	not received					40 [ms] once / DCY	2 DCY
			OR
			Response from HV Off Hardware Timer circuit	invalid
Battery Energy Control Module (BECM) - Software Version / Calibration Monitoring
BECM: Dataset Implausible	B2012	compatibility check	dataset and hardware/software	not compatible		BECM mode	= INIT		5 [ms] once / DCY	0 DCY
BECM: Dataset Invalid	B2005	dataset check	dataset	invalid		BECM mode	= INIT		5 [ms] once / DCY	0 DCY
BECM: Production Mode	P0610	vehicle in production mode	production mode	active		for activation:	< 100	[km]	5 [s] once / DCY	0 DCY
BECM: Production Mode	P0610	vehicle in production mode	production mode	active		max mileage since initial vehicle start-up	< 100	[km]	5 [s] once / DCY	0 DCY
BECM: OBD Settings Incompatible	P064F	compatibility check	internal OBD settings and vehicle OBD settings	not compatible		valid message containing vehicle OBD settings	received		2.9 [s] continuous	0 DCY
Battery Energy Control Module (BECM) - Cooling System
Hybrid/EV Battery Pack Coolant Pump Supply Voltage	P0C4D	circuit high	supply voltage @ coolant pump	> 0.4	[V]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Pack Coolant Pump Supply Voltage	P0C4C	circuit low	ratio of supply voltage @ coolant pump to 12 V supply voltage	< 0.9	[-]	coolant pump	switched on		5 [s] continuous	2 DCY
						AND
						BECM mode	= AC_CHARGING
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	HV_OFF
							OR
						BECM mode	= HV_ON

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
Hybrid/EV Battery Pack Coolant Pump "A" Control	P0C49	circuit high	time duration of high signal sent by pump	≥ 10	[s]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Pack Coolant Pump "A" Control	P0C48	circuit low	time duration of ground signal sent by pump	≥ 2	[s]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Pack Coolant Pump "A" Control	P0C47	circuit open (functional check: time out)	alive signal (PWM signal)	missing					39.5 [s] continuous	2 DCY
Hybrid/EV Battery Pack Coolant Pump "A"	P0C4A	performance (functional check: dry run)	time duration of ground signal sent by pump	> 900	[ms]	coolant pump	commanded on	%	7.2 [s] continuous	2 DCY
				<1100	[ms]	pump time out monitoring	passed
			AND			PWM duty cycle	> 85
			pause time between ground signal sent by pump	> 900	[ms]
				<1100	[ms]
Hybrid/EV Battery Pack Coolant Pump	P0CFF	functional check: stuck/stalled	time duration of ground signal sent by pump	>1400	[ms]	coolant pump	commanded on	%	21 [s] continuous	2 DCY
				< 1600	[ms]	pump time out monitoring	passed
			AND			PWM duty cycle	> 25
			pause time between ground signal sent by pump	> 900	[ms]
				<1100	[ms]
Hybrid/EV Battery Pack Coolant Pump "A"	P0C4A	performance (functional check: overheating)	time duration of ground signal sent by pump	>1900	[ms]	coolant pump	commanded on		8.2 [s] continuous	2 DCY
			AND	< 2100	[ms]	pump time out monitoring	passed
			pause time between ground signal sent by pump	> 900	[ms]
				<1100	[ms]
Battery Energy Control Module (BECM) - Cooling Temperature Sensors
Coolant Temperature Sensor at HV Battery Inlet	P0C45	circuit high (short to battery)	signal value of temperature voltage @ HV battery inlet	> 3248.44	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Inlet	P0C44	circuit low (short to ground)	signal value of temperature voltage @ HV battery inlet	< 48.34	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Inlet	P0C42	open circuit	signal value of temperature voltage @ HV battery inlet	> 3125.98	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 3158.20	[mV]		OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Inlet	P0C44	circuit low (out of range low)	signal value of temperature voltage @ HV battery inlet	> 48.34	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 325.48	[mV]		OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Inlet	P0C45	circuit high (out of range high)	signal value of temperature voltage @ HV battery inlet	> 3019.63	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 3125.98	[mV]		OR
			OR			BECM mode	= EMERGENCY_OFF
			signal value of temperature voltage @ HV battery inlet	> 3158.20	[mV]		OR
				< 3248.44	[mV]	BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Inlet	P0C43	range/performance (rationality high)	difference between coolant temperature @ HV battery inlet and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≥ 15...21	[°C]	HV off time calculations status	time calculated	[min]	1.5 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Coolant Temperature Sensor at HV Battery Inlet	P0C43	range/performance (rationality low)	difference between coolant temperature @ HV battery inlet and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≤ -15...-21	[°C]	HV off time calculations status	time calculated	[min]	1.5 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Coolant Temperature Sensor at HV Battery Outlet	P0CD8	circuit high (short to battery)	signal value of temperature voltage @ HV battery outlet	> 3248.44	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Outlet	P0CD7	circuit low (short to ground)	signal value of temperature voltage @ HV battery outlet	< 48.34	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Outlet	P0CD5	open circuit	signal value of temperature voltage @ HV battery outlet	> 3125.98	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 3158.20	[mV]		OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Outlet	P0CD7	circuit low (out of range low)	signal value of temperature voltage @ HV battery outlet	> 48.34	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 325.48	[mV]		OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						BECM mode	OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Outlet	P0CD8	circuit high (out of range high)	signal value of temperature voltage @ HV battery outlet	> 3019.63	[mV]	BECM mode	= AC_CHARGING		5 [s] continuous	2 DCY
				< 3125.98	[mV]		OR
			OR			BECM mode	= EMERGENCY_OFF
			signal value of temperature voltage @ HV battery outlet	> 3158.20	[mV]		OR
				< 3248.44	[mV]	BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
Coolant Temperature Sensor at HV Battery Outlet	P0CD6	range/performance (rationality high)	difference between coolant temperature @ HV battery outlet and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≥ 15...21	[°C]	HV off time calculations status	time calculated	[min]	2 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Coolant Temperature Sensor at HV Battery Outlet	P0CD6	range/performance (rationality low)	difference between coolant temperature @ HV battery outlet and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≤ -15...-21	[°C]	HV off time calculations status	time calculated	[min]	2 [s]continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Coolant Temperature at Chiller	P0CEF	range/performance (rationality high)	difference between pump coolant temperature and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≥ 15...21	[°C]	HV off time calculations status	time calculated	[min]	2.2 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Coolant Temperature at Chiller	P0CEF	range/performance (rationality low)	difference between pump coolant temperature and median value of the coolant temperatures @ HV battery inlet, HV battery outlet and pump coolant temperature	≤ -15...-21	[°C]	HV off time calculations status	time calculated	[min]	2.2 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Battery Energy Control Module (BECM) - High-Voltage System Activation
BJB State Monitoring	P33F0	change to HV_ON fails	BJB mode	!= HV_ON		BJB Target mode	= HV_ON		1 [s] continuous	0 DCY
BJB State Monitoring	P33F0	change to AC_CHARGING fails	BJB mode	!= AC_CHARGING		BJB Target mode	= AC_CHARGING		1 [s] continuous	0 DCY
BJB State Monitoring	P33F0	emergency shutoff	BJB mode	= EMERGENCY_OFF		BECM mode	= AC_CHARGING		1 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= INIT
Battery Energy Control Module (BECM) - Protective Functions
BECM: Hybrid/EV Battery Charging Current	P0CA6	charging current high	measured HV battery charge current	> 0...240	[A]	BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= PRECHARGE
BECM: Hybrid/EV Battery Discharging Current	P0CA7	discharging current high	measured HV battery discharge current	> 0...400	[A]	BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= PRECHARGE
BECM: Hybrid/EV Battery System Voltage	P0AFB	system voltage high	pack voltage signal	> 448	[V]	BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
BECM: Hybrid/EV Battery System Voltage	P0AFA	system voltage low	pack voltage signal	< 187	[V]	BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-01: Hybrid/EV Battery Interface Control Module "A"	P0B26	cell voltage high	any cell voltage signal within CMC-01	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-01: Hybrid/EV Battery Interface Control Module "A"	P0B25	cell voltage low	any cell voltage signal within CMC-01	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-01: Hybrid/EV Battery Interface Control Module "A"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-01	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
CMC-01: Hybrid/EV Battery Interface Control Module "A"	P0BBD	cell voltage rationality check		> 0.25	[V]	BECM mode	OR	500 [ms] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-02: Hybrid/EV Battery Interface Control Module "B"	P0B26	cell voltage high	any cell voltage signal within CMC-02	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-02: Hybrid/EV Battery Interface Control Module "B"	P0B25	cell voltage low	any cell voltage signal within CMC-02	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-02: Hybrid/EV Battery Interface Control Module "B"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-02	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-02: Hybrid/EV Battery Interface Control Module "C"	P0B26	cell voltage high	any cell voltage signal within CMC-03	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-03: Hybrid/EV Battery Interface Control Module "C"	P0B25	cell voltage low	any cell voltage signal within CMC-03	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-03: Hybrid/EV Battery Interface Control Module "C"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-03	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
CMC-03: Hybrid/EV Battery Interface Control Module "C"	P0BBD	cell voltage rationality check		> 0.25	[V]	BECM mode	OR	500 [ms] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-04: Hybrid/EV Battery Interface Control Module "D"	P0B26	cell voltage high	any cell voltage signal within CMC-04	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-04: Hybrid/EV Battery Interface Control Module "D"	P0B25	cell voltage low	any cell voltage signal within CMC-04	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-04: Hybrid/EV Battery Interface Control Module "D"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-04	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-05: Hybrid/EV Battery Interface Control Module "E"	P0B26	cell voltage high	any cell voltage signal within CMC-05	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-05: Hybrid/EV Battery Interface Control Module "E"	P0B25	cell voltage low	any cell voltage signal within CMC-05	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-05: Hybrid/EV Battery Interface Control Module "E"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-05	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
CMC-05: Hybrid/EV Battery Interface Control Module "E"	P0BBD	cell voltage rationality check		> 0.25	[V]	BECM mode	OR	500 [ms] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-06: Hybrid/EV Battery Interface Control Module "F"	P0B26	cell voltage high	any cell voltage signal within CMC-06	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-06: Hybrid/EV Battery Interface Control Module "F"	P0B25	cell voltage low	any cell voltage signal within CMC-06	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-06: Hybrid/EV Battery Interface Control Module "F"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-06	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-07: Hybrid/EV Battery Interface Control Module "G"	P0B26	cell voltage high	any cell voltage signal within CMC-07	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-07: Hybrid/EV Battery Interface Control Module "G"	P0B25	cell voltage low	any cell voltage signal within CMC-07	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-07: Hybrid/EV Battery Interface Control Module "G"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-07	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
CMC-07: Hybrid/EV Battery Interface Control Module "G"	P0BBD	cell voltage rationality check		> 0.25	[V]	BECM mode	OR	500 [ms] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-08: Hybrid/EV Battery Interface Control Module "H"	P0B26	cell voltage high	any cell voltage signal within CMC-08	> 4.3	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-08: Hybrid/EV Battery Interface Control Module "H"	P0B25	cell voltage low	any cell voltage signal within CMC-08	< 1.8...2.0	[V]	BECM mode	= AC_CHARGING	100 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
CMC-08: Hybrid/EV Battery Interface Control Module "H"	P0BBD	cell voltage rationality check	difference between maximum cell voltage and minimum cell voltage within CMC-08	> 0.25	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= INIT
							OR
						BECM mode	= PRECHARGE
BECM: Daisy Chain Redundant Safety Shutdown	P0AF8	redundant safety shutdown due to cell overvoltage/undervoltage	BECM Daisy Chain input	< 4	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= PRECHARGE
BJB: Main Fuse	P0A95	rationality check	deviation between battery voltage and voltage at main fuse	> \|20\|	[V]	BECM mode	= AC_CHARGING	5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
BJB: Battery Charger Fuse	P0E2E	rationality check	deviation between system voltage and voltage at battery charger fuse	> \|20\|	[V]	BECM mode	= AC_CHARGING	5 [s] continuous	2 DCY
							OR
						BECM mode	= HV_ON
BECM: Vehicle System - 12 Volt Supply Voltage	P0563	system voltage high	power supply voltage	> 17	[V]			9 [s] continuous	0 DCY
BECM: Vehicle System - 12 Volt Supply Voltage	U1401	system voltage high	power supply voltage	> 17	[V]			10 [ms] continuous	0 DCY
BECM: Vehicle System - 12 Volt Supply Voltage	P0562	system voltage low	power supply voltage	< 8	[V]			9 [s] continuous	0 DCY
BECM: Vehicle System - 12 Volt Supply Voltage	U1400	system voltage low	power supply voltage	< 8	[V]			10 [ms] continuous	0 DCY
BECM: Vehicle System - 12 Volt Supply Voltage	U1400	system voltage pre-low	power supply voltage	< 9	[V]			10 [ms] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
BECM: Crash Detection	P1609	crash shut-off was triggered	crash	detected	System	active		0 [ms] continuous	0 DCY
Battery Energy Control Module (BECM) - CAN Communication Monitoring
Hybrid CAN	U0028	vehicle communication bus A	CAN controller enters "BUS OFF" state	3 times in a row	time after ECU wake up	> 500	[ms]	450 [ms] continuous	0 DCY
Hybrid CAN	U0029	vehicle communication bus A performance	CAN messages	not received	time after ECU wake up	> 500	[ms]	450 [ms] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	FlexRay	active	[ms]	5 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	time after ECU wake up	> 500	[ms]	800 [ms] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	FlexRay	active	[ms]	800 [ms] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	2 DCY
Hybrid CAN: Engine Control Module (ECM)	U0100	lost communication with ECM/PCM "A"	message time out	detected	FlexRay	active	[ms]	2 [s] continuous	2 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	message counter error	detected	time after ECU wake up	> 500	[ms]	8 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	message counter error	detected	valid message from ECM	received	[ms]	8 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	checksum error	detected	time after ECU wake up	> 500	[ms]	2.5 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	checksum error	detected	valid message from ECM	received	[ms]	2.5 [s] continuous	0 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	received message	implausible message	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Engine Control Module (ECM)	U0401	invalid data received from ECM/PCM "A"	received message	implausible message	valid message from ECM	received	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Body Control Module "A"	U0140	lost communication with Body Control Module	message time out	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	2 DCY
Hybrid CAN: Body Control Module "A"	U0140	lost communication with Body Control Module	message time out	detected	Comfort CAN	active	[ms]	2 [s] continuous	2 DCY
Hybrid CAN: Body Control Module "A"	U0141	lost communication with Body Control Module "A"	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Hybrid CAN: Body Control Module "A"	U0141	lost communication with Body Control Module "A"	message time out	detected	ComfortCAN	active	[ms]	1 [s] continuous	0 DCY
Hybrid CAN: Gateway "A"	U0146	lost communication with Gateway "A"	message time out	detected	(BECM mode	= AC_CHARGING	[ms]	1 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					time after ECU wake up	> 500
					any Hybrid CAN message	received
Hybrid CAN: Gateway "A"	U0447	invalid data received from Gateway "A"	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Hybrid CAN: Gateway "A"	U0447	invalid data received from Gateway "A"	message counter error	detected	valid message from Gateway	received	[ms]	1 [s] continuous	0 DCY
Hybrid CAN: Gateway "A"	U0447	invalid data received from Gateway "A"	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Hybrid CAN: Gateway "A"	U0447	invalid data received from Gateway "A"	checksum error	detected	valid message from Gateway	received	[ms]	200 [ms] continuous	0 DCY
Hybrid CAN: Gateway "A"	U0447	invalid data received from Gateway "A"	BECM target mode	!= AC_CHARGING	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
				!= HV_OFF	valid message from Gateway	received
				!= HV_ON
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B	lost communication with Battery Charger Control Module "A"	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B			detected	Hybrid CAN communication	active	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B	lost communication with Battery Charger Control Module "A"	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B	lost communication with Battery Charger Control Module "A"	message time out	detected	Hybrid CAN communication	active	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B	lost communication with Battery Charger Control Module "A"	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Battery Charger Control Module (BCCM)	U019B	lost communication with Battery Charger Control Module "A"	message time out	detected	Hybrid CAN communication	active	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0116	lost communication with Coolant Temperature Control Module	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0116	lost communication with Coolant Temperature Control Module	message time out	detected	Hybrid CAN communication	active	[ms]	1 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0116	lost communication with Coolant Temperature Control Module	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0116	lost communication with Coolant Temperature Control Module	message time out	detected	Hybrid CAN communication	active	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0456	invalid data received from Coolant Temperature Control Module	received message	implausible message	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0456			implausible message	valid message from VTMC	received	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0456	invalid data received from Coolant Temperature Control Module	received message	implausible message	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Hybrid CAN: Coolant Temperature Control Module	U0456		received message	implausible message	valid message from VTMC	received	[ms]	5 [s] continuous	2 DCY
Battery CAN	U0037	vehicle communication bus B	CAN controller enters "BUS OFF" state	3 times in a row	time after ECU wake up	> 500	[ms]	10 [ms] continuous	0 DCY
Battery CAN	U0038	vehicle communication bus B performance (global time out)	CAN messages	not received	time after ECU wake up	> 500	[ms]	450 [ms] continuous	0 DCY
Battery CAN	U0038	vehicle communication bus B performance (global time out)	CAN messages	not received	CMC power supply	active	[ms]	450 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	500 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A			detected	any Battery CAN message	received	[ms]	500 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	500 [ms] continuous	0 DCY
	U059B			detected	valid message from BJB	received	[ms]	500 [ms] continuous
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	20 [ms] continuous	0 DCY
	U059B			detected	valid message from BJB	received	[ms]	20 [ms] continuous
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		message counter error	detected	valid message from BJB	received	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from BJB	received
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		message counter error	detected	valid message from BJB	received	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		checksum error	detected	valid message from BJB	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		message counter error	detected	valid message from BJB	received	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		checksum error	detected	valid message from BJB	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		message counter error	detected	valid message from BJB	received	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		checksum error	detected	valid message from BJB	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	message counter error	detected	time after ECU wake up	> 500	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		message counter error	detected	valid message from BJB	received	[ms]	4 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		checksum error	detected	valid message from BJB	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A	lost communication with Hybrid/EV Battery Pack Sensor Module (BJB)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U029A		message time out	detected	any Battery CAN message	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B			implausible	valid message from BJB	received	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	800 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B		received message	implausible	valid message from BJB	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U01A0			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U04A1			detected	valid message from CMC-01	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A1			detected	valid message from CMC-01	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-01	received
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		message counter error	detected	valid message from CMC-01	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		checksum error	detected	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1			implausible	valid message from CMC-01	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1	invalid data received from Hybrid/EV Battery Interface Control Module "A" (CMC-01)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U04A1		received message	implausible	valid message from CMC-01	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0	lost communication with Hybrid/EV Battery Interface Control Module "A" (CMC-01)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "A"	U01A0		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U01A1			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U04A2			detected	valid message from CMC-02	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A2			detected	valid message from CMC-02	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-02	received
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		message counter error	detected	valid message from CMC-02	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		checksum error	detected	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2			implausible	valid message from CMC-02	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2	invalid data received from Hybrid/EV Battery Interface Control Module "B" (CMC-02)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U04A2		received message	implausible	valid message from CMC-02	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1	lost communication with Hybrid/EV Battery Interface Control Module "B" (CMC-02)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "B"	U01A1		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U01A2			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U04A3			detected	valid message from CMC-03	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A3			detected	valid message from CMC-03	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		message counter error	detected	valid message from CMC-03	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-03	received
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		checksum error	detected	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3			implausible	valid message from CMC-03	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3	invalid data received from Hybrid/EV Battery Interface Control Module "C" (CMC-03)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U04A3		received message	implausible	valid message from CMC-03	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2	lost communication with Hybrid/EV Battery Interface Control Module "C" (CMC-03)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "C"	U01A2		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U01A3			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U02A0			detected	valid message from CMC-04	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U02A0			detected	valid message from CMC-04	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		message counter error	detected	valid message from CMC-04	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		checksum error	detected	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0			implausible	valid message from CMC-04	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0	invalid data received from Hybrid/EV Battery Interface Control Module "D" (CMC-04)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U02A0		received message	implausible	valid message from CMC-04	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3	lost communication with Hybrid/EV Battery Interface Control Module "D" (CMC-04)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "D"	U01A3		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4			detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-05	received
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A5			detected	valid message from CMC-05	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		message counter error	detected	valid message from CMC-05	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		checksum error	detected	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5			implausible	valid message from CMC-05	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5	invalid data received from Hybrid/EV Battery Interface Control Module "E" (CMC-05)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U04A5		received message	implausible	valid message from CMC-05	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4	lost communication with Hybrid/EV Battery Interface Control Module "E" (CMC-05)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "E"	U01A4		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5			detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U04A6			detected	valid message from CMC-06	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A6			detected	valid message from CMC-06	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-06	received
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		message counter error	detected	valid message from CMC-06	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		checksum error	detected	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6			implausible	valid message from CMC-06	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6	invalid data received from Hybrid/EV Battery Interface Control Module "F" (CMC-06)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U04A6		received message	implausible	valid message from CMC-06	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5	lost communication with Hybrid/EV Battery Interface Control Module "F" (CMC-06)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "F"	U01A5		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U01A6			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
	U04A7			detected	valid message from CMC-07	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
	U04A7			detected	valid message from CMC-07	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-07	received
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		message counter error	detected	valid message from CMC-07	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		checksum error	detected	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7			implausible	valid message from CMC-07	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7	invalid data received from Hybrid/EV Battery Interface Control Module "G" (CMC-07)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U04A7		received message	implausible	valid message from CMC-07	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6	lost communication with Hybrid/EV Battery Interface Control Module "G" (CMC-07)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "G"	U01A6		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7			detected	CMC power supply	active	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8			detected	valid message from CMC-08	received	[ms]	1 [s] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8			detected	valid message from CMC-08	received	[ms]	200 [ms] continuous
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	2 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	200 [ms] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
					valid message from CMC-08	received
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message counter error	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		message counter error	detected	valid message from CMC-08	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	checksum error	detected	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		checksum error	detected	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	received message	implausible	time after ECU wake up	> 500	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8			implausible	valid message from CMC-08	received	[ms]	1 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8	invalid data received from Hybrid/EV Battery Interface Control Module "H" (CMC-08)	received message	implausible	time after ECU wake up	> 500	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U04A8		received message	implausible	valid message from CMC-08	received	[ms]	5 [s] continuous	0 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7	lost communication with Hybrid/EV Battery Interface Control Module "H" (CMC-08)	message time out	detected	time after ECU wake up	> 500	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Interface Control Module "H"	U01A7		message time out	detected	CMC power supply	active	[ms]	5 [s] continuous	2 DCY
Battery CAN: Hybrid/EV Battery Pack Sensor Module	U059B	invalid data received from Hybrid/EV Battery Pack Sensor Module (BJB)	BJB error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "A" (CMC-01)	P0DAF	range/performance (invalid data) (CMC-01)	CMC-01 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "B" (CMC-02)	P0DB3	range/performance (invalid data) (CMC-02)	CMC-02 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "C" (CMC-03)	P0DB7	range/performance (invalid data) (CMC-03)	CMC-03 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "D" (CMC-04)	P0DBB	range/performance (invalid data) (CMC-04)	CMC-04 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "E" (CMC-05)	P0DBF	range/performance (invalid data) (CMC-05)	CMC-05 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF
						OR
					BECM mode	= HV_OFF
						OR
					BECM mode)	= HV_ON
					Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "F" (CMC-06)	P0DC3	range/performance (invalid data) (CMC-06)	CMC-06 error memory status flag	not valid	(BECM mode	= AC_CHARGING		2.5 [s] continuous	0 DCY
						OR
					BECM mode	= EMERGENCY_OFF

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "G" (CMC-07)	P0DC7	range/performance (invalid data) (CMC-07)	CMC-07 error memory status flag	not valid		(BECM mode	= AC_CHARGING	2.5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
Battery CAN: Hybrid/EV Battery Cell Balancing Circuit "H" (CMC-08)	P0DCB	range/performance (invalid data) (CMC-08)	CMC-08 error memory status flag	not valid		(BECM mode	= AC_CHARGING	2.5 [s] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Hardware/Internal Malfunctions
BJB: Internal Hardware Check (Self Test)	P0AFC	internal hardware check (self test)	CASE 1:			CASE 1:		CASE 1:	0 DCY
			crash self test	not completed		BJB mode	= INIT	4.5 [s]
			OR			Battery CAN communication	active
			non-volatile memory reading	not completed		BJB error memory status flag	valid	CASE 2:
			OR					550 [ms]
			sensor data	not available		CASE 2 to 9:
			OR			Battery CAN communication	active	CASE 3:
			hardware revision	not available		BJB error memory status flag	valid	1 [s]
			CASE 2:					CASE 4:
			contactor control command and contactor control feedback signal	not equal				5500 [ms]
			CASE 3:					CASE 5:
			Mosfet control command and mosfet control feedback signal	not equal				1 [s]
			CASE 4:					CASE 6:
			Difference between temperature @ control board NTC and temperature @ shunt NTC 1	> \|20\|	[°C]			1 [s]
			OR
			Difference between temperature @ shunt NTC 1 and temperature @ shunt NTC 2	> \|20\|	[°C]			CASE 7:
			CASE 5:					550 [ms]
			deviation between positive battery voltage and voltage @ main fuse	> \|20\|	[V]			CASE 8:
			CASE 6:					750 [ms]
			deviation between positive system voltage and voltage @ battery charger fuse	> \|20\|	[V]			CASE 9:
			CASE 7:					550 [ms]
			ADC internal reference voltage of main processor	≥1.32	[V]
			OR
			ADC internal reference voltage of main processor	≤ 1.08	[V]
			CASE 8:
			HV isolated positive supply voltage	> 7	[V]
			OR	< 5.5	[V]
			HV isolated negative supply voltage	> -2	[V]
			CASE 9:	< -6	[V]
			3.3V supply voltage	> 3.6	[V]
			OR	< 3	[V]
			5V supply voltage	> 5.4	[V]
				< 4.6	[V]

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
BJB: Internal Memory	P0AFC	RAM check	CASE 1:			CASE 1:		CASE 1:	0 DCY
			error correcting code failure	detected		BECM mode	= INIT	850 [ms] once / DCY
			CASE 2:			CASE 1 & 2:		CASE 2:
			ECC correction check logic	failed		Battery CAN communication	active	500 [ms] continuous
						BJB error memory status flag	valid
BJB: EEPROM	P0AFC	EEPROM check	memory checksum error	detected		BECM mode	= INIT	850 [ms] once / DCY	0 DCY
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Analog-to-Digital-Converter 1	P0AFC	analog-to -digital converter 1 internal hardware check	internal reference voltage	> 5.5	[V]	Battery CAN communication	active	750 [ms] continuous	0 DCY
BJB: Analog-to-Digital-Converter 1	P0AFC	analog-to -digital converter 1 internal hardware check	internal reference voltage	< 4.5	[V]	BJB error memory status flag	valid	750 [ms] continuous	0 DCY
BJB: Analog-to-Digital-Converter 2	P0AFC	analog-to -digital converter 2 internal hardware check	CASE 1:			CASE 1 & 2:		CASE 1 & 3 & 4:	0 DCY
			internal reference voltage for current measurement	>130	[mV]	BECM mode	= INIT	700 [ms] continuous
				<110	[mV]	Battery CAN communication	active
			OR			BJB error memory status flag	valid	CASE 2:
			internal reference voltage for voltage measurement	> 1.2	[V]			5.5 [s] continuous
				< 0.8	[V]	CASE 3 & 4:
			OR			Battery CAN communication	active
			internal resistance ratio for temperature measurement	> 0.763	[%]	BJB error memory status flag	valid
			CASE 2:	< 0.534	[%]
			main processor data	not received
			CASE 3:
			ADC values	not received
			CASE 4:
			shunt resistance	> 1.25	[MOhm]
BJB: Hardware Disable Malfunction	P0AFC	plausibility check	CASE 1:			Battery CAN communication	active	CASE 1:	0 DCY
			Hardware-Disable output voltage	> 3.703	[V]	BJB error memory status flag	valid	1.5 [s] continuous
			Hardware-Disable comparator output	0
			OR					CASE 2 to 6:
			Hardware-Disable output voltage	< 2.381	[V]			2.5 [s] continuous
			Hardware-Disable comparator output	1
			CASE 2:
			car crash	detected
			contactor power supply activity signal	active
			CASE 3:
			emergency off command	issued
			contactor power supply activity signal	active
			CASE 4:
			contactor power supply output voltage	< 4	[V]
			contactor power supply activity signal	active
			CASE 5:
			contactor power supply output voltage	> 6	[V]
			contactor power supply activity signal	inactive
			CASE 6:
			Hardware-Disable output voltage	> 3.703	[V]
			Hardware-Disable comparator output	1
			contactor power supply input voltage	< 16.2	[V]
			contactor power supply input voltage	> 7.8	[V]
			car crash	not detected
			contactor power supply activity signal	inactive
			contactor power supply output voltage	<4	[V]
BJB: Hardware Disable Line	P0E2D	performance (circuit high/out of range high)	CASE 1: short to battery			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured voltage	> 17	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage	> 16	[V]
				≤ 17	[V]

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
BJB: Hardware Disable Line	P0E2D	performance (open circuit)	actual value of Hardware-Disable state	= disable		target value of Hardware-Disable state	= enable	600 [ms] continuous	0 DCY
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Current Sensors
BJB: Hybrid/EV Battery Pack Current Sensor "A"	P0AC2	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured shunt current	> 455	[A]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured shunt current	> 400	[A]
				≤ 455	[A]
BJB: Hybrid/EV Battery Pack Current Sensor "A"	P0AC1	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured shunt current	< -455	[A]	BJB error memory status flag	valid
			CASE 2: out of range low
			measured current	< -400	[A]
				≥ -455	[A]
BJB: Hybrid/EV Battery Pack Current Sensor "A"	P0AC0	circuit range/performance (internal hardware check)	internal communication time out	detected		Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Pack Current Sensor "A"	P0AC0	circuit range/performance (internal hardware check)	internal communication time out	detected		BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Pack Current Sensor "B"	P0B11	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	2 DCY
			measured hull current	> 455	[A]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured hull current	> 400	[A]
				≤ 455	[A]
BJB: Hybrid/EV Battery Pack Current Sensor "B"	P0B10	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active	1 [s] continuous	2 DCY
			measured hull current	< -455	[A]	BJB error memory status flag	valid
			CASE 2: out of range low
			measured hull current	< -400	[A]
				≥ -455	[A]
BJB: Hybrid/EV Battery Pack Current Sensor "B"	P0B0F	circuit range/performance (internal hardware check)	deviation between sensor "B" digital value and sensor "B" analog value	≥ \|50\|	[A]	Battery CAN communication	active	750 [ms] continuous	2 DCY
BJB: Hybrid/EV Battery Pack Current Sensor "B"	P0B0F	circuit range/performance (internal hardware check)		≥ \|50\|	[A]	BJB error memory status flag	valid	750 [ms] continuous	2 DCY
BJB: Hybrid/EV Battery Pack Current Sensors "A" and "B"	P0B13	rationality check	CASE 1:			Battery CAN communication	active	CASE 1:	0 DCY
			deviation between measured current value of sensor 1 and measured current value of sensor 2	> \|3\|+ \|5% of the current value of sensor 1 \|	[A]	BJB error memory status flag	valid	1.5 [s] continuous
			CASE 2:					CASE 2:
			deviation between measured current value of sensor 1 and measured current value of sensor 2	> \|50\|	[A]			750 [ms] continuous
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Temperature Sensors
BJB: Temperature Sensors	P0AFC	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1.5 [s] continuous	2 DCY
			signal value of control board NTC temperature voltage	≤ -45	[°C]	BJB error memory status flag	valid
			OR
			corresponding temperature of shunt board NTC sensor signal value	≤ -45	[°C]
			OR
			signal value of shunt NTC 1 temperature voltage	≤ -45	[°C]
			OR
			signal value of shunt NTC 2 temperature voltage	≤ -45	[°C]
			CASE 2: out of range high
			signal value of control board NTC temperature voltage	< - 40	[°C]
			OR	> -45	[°C]
			corresponding temperature of shunt board NTC sensor signal value	< - 40	[°C]
			OR	> -45	[°C]
			signal value of shunt NTC 1 temperature voltage	< - 40	[°C]
			OR	> -45	[°C]
			signal value of shunt NTC 2 temperature voltage	< - 40	[°C]
				> -45	[°C]
BJB: Temperature Sensors	P0AFC	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active	1.5 [s] continuous	2 DCY
			signal value of control board NTC temperature voltage	≥ 135	[°C]	BJB error memory status flag	valid
			OR
			corresponding temperature of shunt board NTC sensor signal value	≥ 135	[°C]
			OR
			signal value of shunt NTC 1 temperature voltage	≥ 135	[°C]
			OR
			signal value of shunt NTC 2 temperature voltage	≥ 135	[°C]

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
			CASE 2: out of range low
			signal value of control board NTC temperature voltage	> 125	[°C]
			OR	< 135	[°C]
			corresponding temperature of shunt board NTC sensor signal value	> 125	[°C]
			OR	< 135	[°C]
			signal value of shunt NTC 1 temperature voltage	> 125	[°C]
			OR	< 135	[°C]
			signal value of shunt NTC 2 temperature voltage	> 125	[°C]
				< 135	[°C]
BJB: Temperature Sensors	P0AFC	rationality check high	difference between any BJB temperature and median value of all BJB temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	1 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
BJB: Temperature Sensors	P0AFC	rationality check low	difference between any BJB temperature and median value of all BJB temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	1 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Voltage Sensors
BJB: Hybrid/EV Battery Pack Voltage Sensor "A" - Battery Voltage Positive Terminal Sensor	P0ABD	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active		1 [s] continuous	0 DCY
			measured voltage	> 505	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage	> 465	[V]
				≤ 505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "A" - Battery Voltage Positive Terminal Sensor	P0ABC	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active		1 [s] continuous	0 DCY
			measured voltage	< 2	[V]	BJB error memory status flag	valid
			deviation between battery voltage and voltage @ main fuse	> \|20\|	[V]
			CASE 2: out of range low
			measured voltage	< 160	[V]
				≥ 2	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "A" - Battery Voltage Positive Terminal Sensor	P0ABB	circuit range/performance (rationality check high)	difference between battery voltage and sum of all cell voltages	> 40	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR
						BECM mode	= PRECHARGE
BJB: Hybrid/EV Battery Pack Voltage Sensor "A" - Battery Voltage Positive Terminal Sensor	P0ABB	circuit range/performance (rationality check low)	difference between battery voltage and sum of all cell voltages	< -40	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	0 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
							OR

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BECM mode	= PRECHARGE
BJB: Hybrid/EV Battery Pack Voltage Sensor "B" - System Voltage Positive Terminal Sensor	P0B17	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured system voltage at positive terminal	> 505	[V]	BJB error memory status flag	valid	1 [s] continuous	0 DCY
			CASE 2: out of range high
			measured system voltage at positive terminal	> 465	[V]
				≤ 505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "B" - System Voltage Positive Terminal Sensor	P0B16	circuit low	measured system voltage at positive terminal	< -30	[V]	(BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Pack Voltage Sensor "B" - System Voltage Positive Terminal Sensor	P0B14	circuit open	deviation between measured system voltage @ positive terminal and measured voltage @ battery charger fuse	> \|20\|	[V]	(BECM mode	= AC_CHARGING	1 [s] continuous	0 DCY
			measured system voltage at positive terminal	< 10	[V]		OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Pack Voltage Sensor "B" - System Voltage Negative Terminal Sensor	P0B17	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured system voltage at negative terminal	> 505	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured system voltage at negative terminal	> 465	[V]
				≤ 505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "B" - System Voltage Negative Terminal Sensor	P0B16	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured system voltage at negative terminal	< -505	[V]	BJB error memory status flag	valid
			CASE 2: out of range low
			measured system voltage at negative terminal	< -465	[V]
				≥ -505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "B"	P0B15	circuit range/performance (rationality check high)	difference between system voltage and battery voltage	> 40	[V]	BECM mode	= AC_CHARGING	2 [s] continuous	0 DCY
							OR
						BECM mode	= HV_ON
BJB: Hybrid/EV Battery Pack Voltage Sensor "B"	P0B15	circuit range/performance (rationality check low)	difference between system voltage and battery voltage	< -40	[V]	BECM mode	= AC_CHARGING	2 [s] continuous	0 DCY
							OR
						BECM mode	= HV_ON
BJB: Hybrid/EV Battery Pack Voltage Sensor "C"	P0B1C	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured voltage at hybrid/EV battery pack voltage sensor "C"	> 505	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage at hybrid/EV battery pack voltage sensor "C"	> 465	[V]
				≤ 505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "C"	P0B1B	circuit low/out of range low	CASE 1: circuit low			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured voltage at hybrid/EV battery pack voltage sensor "C"	< -30	[V]	BJB error memory status flag	valid
			CASE 2: out of range low
			measured voltage at hybrid/EV battery pack voltage sensor "C"	< 140	[V]
				≥ -30	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "D"	P0B21	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	2 DCY
			measured voltage at hybrid/EV battery pack voltage sesnor "D"	> 505	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage at hybrid/EV battery pack voltage sesnor "D"	> 465	[V]
				≤ 505	[V]
BJB: Hybrid/EV Battery Pack Voltage Sensor "D"	P0B20	circuit low	measured voltage at hybrid/EV battery pack voltage sesnor "D"	< -30	[V]	Battery CAN communication	active	1 [s] continuous	2 DCY
BJB: Hybrid/EV Battery Pack Voltage Sensor "D"	P0B20	circuit low		< -30	[V]	BJB error memory status flag	valid	1 [s] continuous	2 DCY
BJB: Hybrid/EV Battery Pack Voltage Sensor "D"	P0B1E	open circuit	deviation between measured system voltage at positive terminal and measured voltage at hybrid/EV battery pack voltage sesnor "D"	> 20	[V]	Battery CAN communication	active	1 [s] continuous	2 DCY
BJB: Hybrid/EV Battery Pack Voltage Sensor "D"	P0B1E	open circuit	measured voltage at hybrid/EV battery pack voltage sesnor "D"	< 10	[V]	BJB error memory status flag	valid	1 [s] continuous	2 DCY
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Low Voltage Sensors
BJB: Sensor Power Supply "B"	P06B5	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	2 DCY
			measured voltage	> 26	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage	> 16.2	[V]
				≤ 26	[V]
BJB: Sensor Power Supply "B"	P06B4	circuit low	measured voltage	< 7.8	[V]	Battery CAN communication	active	1 [s] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						BJB error memory status flag	valid
BJB: contactor Supply Voltage Sensor	P0B36	circuit high/out of range high	CASE 1: circuit high			Battery CAN communication	active	1 [s] continuous	0 DCY
			measured voltage	> 26	[V]	BJB error memory status flag	valid
			CASE 2: out of range high
			measured voltage	> 16.2	[V]
				≤ 26
BJB: contactor Supply Voltage Sensor	P0B35	circuit low	measured voltage	< 7.8	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
BJB: contactor Supply Voltage Sensor	P0B35	circuit low	measured voltage	< 7.8	[V]	BJB error memory status flag	valid	1 [s] continuous	0 DCY
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - contactors
BJB: Hybrid/EV Battery Positive Main contactor Circuit	P0AA1	stuck closed	deviation between voltages before and after the main contactor on the positive HV busbar	< \|20\|	[V]	(BECM mode	= HV_OFF	4.5 [s] continuous	0 DCY
							OR
						BECM mode)	= EMERGENCY_OFF
						positive main contactor is commanded	open
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Positive Main contactor Circuit	P0AA2	stuck open	deviation between voltage before and after the main contactor on the positive HV busbar	> \|60\|	[V]	(BECM mode	= AC_CHARGING	1.5 [s] continuous	0 DCY
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Negative Main contactor Circuit	P0AA4	stuck closed	measured voltage after the main contactor on the negative HV busbar	< 20	[V]	(BECM mode	= HV_OFF	4.5 [s] continuous	0 DCY
			modeled voltage after the main contactor on the negative HV busbar	> 20	[V]		OR
						BECM mode)	= EMERGENCY_OFF
						negative main contactor is commanded	open
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Negative Main contactor Circuit	P0AA5	stuck open	voltage on the negative HV busbar	> 60	[V]	(BECM mode	= AC_CHARGING	1.5 [s] continuous	0 DCY
							OR
						BECM mode)	= HV_ON
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Precharge contactor Circuit	P0AE3	stuck open	precharge energy	= 0	[Ws]	BECM mode	= PRECHARGE	1 [s]	0 DCY
			negative main contactor remains open error (P0AA5)	not detected		precharge time out (P0C78)	detected	continuous
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Hybrid/EV Battery Positive Main contactor Control	P0AD9	circuit open (functional check)	contactor supply voltage	> 10	[V]	Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Positive Main contactor Control	P0AD9	circuit open (functional check)	contactor driver feedback current	> 650	[mA]	BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Positive Main contactor Control	P0ADC	circuit high	contactor driver input	OFF		Battery CAN communication	active	700 [ms] continuous	0 DCY
			contactor driver feedback current	> 100	[mA]	BJB error memory status flag	valid
				< 650	[mA]
BJB: Hybrid/EV Battery Positive Main contactor Control	P0ADB	circuit low	contactor driver input	ON	[mA]	Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Positive Main contactor Control	P0ADB	circuit low	contactor driver feedback current	< 100	[mA]	BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0ADD	circuit open (functional check)	contactor supply voltage	> 10	[V]	Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0ADD	circuit open (functional check)	contactor driver feedback current	> 650	[mA]	BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0AE0	circuit high	contactor driver input	OFF	[mA]	Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0AE0	circuit high	contactor driver feedback current	> 100	[mA]	BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0ADF	circuit low	contactor driver input	ON	[mA]	Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Negative Main contactor Control	P0ADF	circuit low	contactor driver feedback current	< 100	[mA]	BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Precharge contactor Control	P0AE7	circuit high	contactor driver input	OFF		Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Precharge contactor Control	P0AE7	circuit high	contactor driver feedback	ON		BJB error memory status flag	valid	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Precharge contactor Control	P0AE6	circuit low	contactor driver input	ON		Battery CAN communication	active	700 [ms] continuous	0 DCY
BJB: Hybrid/EV Battery Precharge contactor Control	P0AE6	circuit low	contactor driver feedback	OFF		BJB error memory status flag	valid	700 [ms] continuous	0 DCY
Hybrid/EV Battery Pack Sensor Module (Battery Junction Box (BJB)) - Protective Functions
BJB: Precharging System	P0CA7	discharging current high	measured shunt current	< - 8	[A]	BECM mode	= PRECHARGE	550 [ms] continuous	0 DCY
						Battery CAN communication	active
						BJB error memory status flag	valid
BJB: Precharging System	P0C78	functional check: precharge time too long	deviation between battery positive voltage and system voltage	> \|10\|	[V]	BECM mode	= PRECHARGE	1 [s] continuous	0 DCY
						Battery CAN communication	active
						BJB error memory status flag	valid
Battery Junction Box (BJB) - Communication Monitoring
BJB: Communication	U0111	lost communication with Battery Energy Contrl Module "A"	CASE 1:			CASE 1:		CASE 1:	0 DCY
			message time out	detected		Battery CAN communication	active	1.5 [s] continuous
			CASE 2:			BJB error memory status flag	valid	CASE 2:
			message counter error	detected		CASE 2 & 3:		1.5 [s] continuous

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
				detected		Battery CAN communication	active
			CASE 3:			BJB error memory status flag	valid
			checksum error			message from BECM	received	CASE 3:
								600 [ms] continuous
Cell Module Controller (CMC) - Hardware/Internal Malfunctions
CMC-01: Internal Memory	P0DAC	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-01 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-01: AD Converter	P0DAC	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-01: AD Converter	P0DAC	AD converter error of main path		≥ 20	[-]	CMC-01 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-01: Internal Error	P0DAC	internal error in main path	CASE 1:		[%]	Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-01 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated	1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:		CASE 3:
			Watchdog test error	detected		Shut down	initiated	500 [ms] once / DCY
			CASE 4:					CASE 4:
			MCU malfunction	detected				500 [ms] continuous
CMC-02: Internal Memory	P0DB0	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-02 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-02: AD Converter	P0DB0	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-02: AD Converter	P0DB0	AD converter error of main path		≥ 20	[-]	CMC-02 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-02: Internal Error	P0DB0	internal error in main path	CASE 1:		[%]	Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-02 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated	1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:		CASE 3:
			Watchdog test error	detected		Shut down	initiated	500 [ms] once / DCY
			CASE 4:					CASE 4:
			MCU malfunction	detected				500 [ms] continuous
CMC-03: Internal Memory	P0DB4	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-03 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-03: AD Converter	P0DB4	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-03: AD Converter	P0DB4	AD converter error of main path		≥ 20	[-]	CMC-03 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-03: Internal Error	P0DB4	internal error in main path	CASE 1:	detected		Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error			CMC-03 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
			Cell voltage deviation between FET switch on and FET switch off	< 2	[%]	Start up	initiated	1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:		CASE 3:
			Watchdog test error	detected		Shut down	initiated	500 [ms] once / DCY
			CASE 4:					CASE 4:
			MCU malfunction	detected				500 [ms] continuous
CMC-04: Internal Memory	P0DB8	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-04 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-04: AD Converter	P0DB8	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-04: AD Converter	P0DB8	AD converter error of main path		≥ 20	[-]	CMC-04 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-04: Internal Error	P0DB8	internal error in main path	CASE 1:		[%]	Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-04 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated	1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:		CASE 3:
			Watchdog test error	detected		Shut down	initiated	500 [ms] once / DCY
			CASE 4:					CASE 4:
			MCU malfunction	detected				500 [ms] continuous
CMC-05: Internal Memory	P0DBC	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-05 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-05: AD Converter	P0DBC	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-05: AD Converter	P0DBC	AD converter error of main path		≥ 20	[-]	CMC-05 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-05: Internal Error	P0DBC	internal error in main path	CASE 1:		[%]	Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-05 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated	1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:		CASE 3:
			Watchdog test error	detected		Shut down	initiated	500 [ms] once / DCY
			CASE 4:					CASE 4:
			MCU malfunction	detected				500 [ms] continuous
CMC-06: Internal Memory	P0DC0	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active	CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-06 error memory status flag	valid	500 [ms] continuous
			CASE 2: RAM/ROM error during startup					CASE 2 & 3:
			RAM/ROM error	detected				500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-06: AD Converter	P0DC0	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active	2.5 [s] continuous	0 DCY
CMC-06: AD Converter	P0DC0	AD converter error of main path		≥ 20	[-]	CMC-06 error memory status flag	valid	2.5 [s] continuous	0 DCY
CMC-06: Internal Error	P0DC0	internal error in main path	CASE 1:	detected		Battery CAN communication	active	CASE 1:	0 DCY
			Daisy chain stuck error			CMC-06 error memory status flag	valid	550 [ms] continuous
			CASE 2:			Additionally for CASE 2:		CASE 2:

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
			Cell voltage deviation between FET switch on and FET switch off	< 2	[%]	Start up	initiated		1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:			CASE 3:
			Watchdog test error	detected		Shut down	initiated		500 [ms] once / DCY
			CASE 4:						CASE 4:
			MCU malfunction	detected					500 [ms] continuous
CMC-07: Internal Memory	P0DC4	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active		CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-07 error memory status flag	valid		500 [ms] continuous
			CASE 2: RAM/ROM error during startup						CASE 2 & 3:
			RAM/ROM error	detected					500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-07: AD Converter	P0DC4	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active		2.5 [s] continuous	0 DCY
CMC-07: AD Converter	P0DC4	AD converter error of main path		≥ 20	[-]	CMC-07 error memory status flag	valid		2.5 [s] continuous	0 DCY
CMC-07: Internal Error	P0DC4	internal error in main path	CASE 1:		[%]	Battery CAN communication	active		CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-07 error memory status flag	valid		550 [ms] continuous
			CASE 2:			Additionally for CASE 2:			CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated		1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:			CASE 3:
			Watchdog test error	detected		Shut down	initiated		500 [ms] once / DCY
			CASE 4:						CASE 4:
			MCU malfunction	detected					500 [ms] continuous
CMC-08: Internal Memory	P0DC8	internal memory tests	CASE 1: RAM/ROM error during operation			Battery CAN communication	active		CASE 1:	0 DCY
			RAM/ROM error	detected		CMC-08 error memory status flag	valid		500 [ms] continuous
			CASE 2: RAM/ROM error during startup						CASE 2 & 3:
			RAM/ROM error	detected					500 [ms] once / DCY
			CASE 3: ECC logic test error
			During ECC logic test, error code	detected
CMC-08: AD Converter	P0DC8	AD converter error of main path	number of communication errors between microcontroller and AD converter	≥ 20	[-]	Battery CAN communication	active		2.5 [s] continuous	0 DCY
CMC-08: AD Converter	P0DC8	AD converter error of main path		≥ 20	[-]	CMC-08 error memory status flag	valid		2.5 [s] continuous	0 DCY
CMC-08: Internal Error	P0DC8	internal error in main path	CASE 1:		[%]	Battery CAN communication	active		CASE 1:	0 DCY
			Daisy chain stuck error	detected		CMC-08 error memory status flag	valid		550 [ms] continuous
			CASE 2: Balancing FET monitoring			Additionally for CASE 2:			CASE 2:
			Cell voltage deviation between FET switch on and FET switch off	< 2		Start up	initiated		1.5 [s] once / DCY
			CASE 3:			Additionally for CASE 3:			CASE 3:
			Watchdog test error	detected		Shut down	initiated		500 [ms] once / DCY
			CASE 4:						CASE 4:
			MCU malfunction	detected					500 [ms] continuous
Cell Module Controller (CMC) - Temperature Sensors
Hybrid/EV Battery Temperature Sensor "A" (CMC-01)	P0A9D	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-01
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "A" (CMC-01)	P0A9E	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-01
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "A" (CMC-01)	P0A9C	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-01 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "A" (CMC-01)	P0A9C	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-01 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "B" (CMC-02)	P0AC7	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-02
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "B" (CMC-02)	P0AC8	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-02
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "B" (CMC-02)	P0AC6	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-02 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "B" (CMC-02)	P0AC6	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-02 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "C" (CMC-03)	P0ACC	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-03
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "C" (CMC-03)	P0ACD	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-03
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "C" (CMC-03)	P0ACB	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-03 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "C" (CMC-03)	P0ACB	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-03 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "D" (CMC-04)	P0AEA	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-04
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "D" (CMC-04)	P0AEB	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-04
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "D" (CMC-04)	P0AE9	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-04 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "D" (CMC-04)	P0AE9	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-04 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "E" (CMC-05)	P0BC4	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-05
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "E" (CMC-05)	P0BC5	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-05
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "E" (CMC-05)	P0BC3	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-05 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "E" (CMC-05)	P0BC3	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-05 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "F" (CMC-06)	P0C35	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-06
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "F" (CMC-06)	P0C36	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-06
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
Hybrid/EV Battery Temperature Sensor "F" (CMC-06)	P0C34	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-06 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "F" (CMC-06)	P0C34	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-06 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "G" (CMC-07)	P0C7E	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-07
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "G" (CMC-07)	P0C7F	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-07
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "G" (CMC-07)	P0C7D	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-07 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "G" (CMC-07)	P0C7D	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-07 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "H" (CMC-08)	P0C83	circuit low (temperature out of range high)	measured cell temperature (from internal cell temperature sensor 1)	> 85	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-08
			measured cell temperature (from internal cell temperature sensor 2)	> 85	[°C]
Hybrid/EV Battery Temperature Sensor "H" (CMC-08)	P0C84	circuit high (temperature out of range low)	measured cell temperature (from internal cell temperature sensor 1)	< -40	[°C]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
			OR			No internal communication error in CMC-08
			measured cell temperature (from internal cell temperature sensor 2)	< -40	[°C]
Hybrid/EV Battery Temperature Sensor "H" (CMC-08)	P0C82	circuit range/performance (temperature rationality check high)	difference between cell internal temperature of CMC-08 and median value of all cell temperatures	≥ 8...15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						BECM mode)	= RUN_ON
Hybrid/EV Battery Temperature Sensor "H" (CMC-08)	P0C82	circuit range/performance (temperature rationality check low)	difference between cell internal temperature of CMC-08 and median value of all cell temperatures	≤ -8...-15	[°C]	HV off time calculations status	time calculated	[min]	2.7 [s] continuous	2 DCY
						HV off time	≥ 360...720
						(BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= INIT
							OR
						BECM mode	= LOCAL_ACTIVE
							OR
						BECM mode)	= RUN_ON
Cell Module Controller (CMC) - Cell Voltage Sensors
Hybrid/EV Battery Voltage Sensor "A" (CMC-01)	P0B3E	circuit high	measured cell voltages in CMC-01	> 4.5	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-01 error memory status flag	valid
						No internal communication error in CMC-01
Hybrid/EV Battery Voltage Sensor "A" (CMC-01)	P0B3D	circuit low	measured cell voltages in CMC-01	< 1	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-01 error memory status flag	valid
						No internal communication error in CMC-01
Hybrid/EV Battery Voltage Sensor "A" (CMC-01)	P0B3B	open circuit	measured cell voltages of broken line and the next higher line in CMC-01	= 5.6	[V]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
						CMC-01 error memory status flag	valid
						No internal communication error in CMC-01
Hybrid/EV Battery Voltage Sensor "A" (CMC-01)	P0B3C	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-01 and ASIC voltage of CMC-01	> 1	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-01 and mean value (ASIC voltage of CMC-01 divided by number of cells in CMC-01)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "A" (CMC-01)	P0B3C	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-01 and ASIC voltage of CMC-01	< -1	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-01 and mean value (ASIC voltage of CMC-01 divided by number of cells in CMC-01)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "B" (CMC-02)	P0B43	circuit high	measured cell voltages in CMC-02	> 4.5	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-02 error memory status flag	valid
						No internal communication error in CMC-02
Hybrid/EV Battery Voltage Sensor "B" (CMC-02)	P0B42	circuit low	measured cell voltages in CMC-02	< 1	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-02 error memory status flag	valid
						No internal communication error in CMC-02
Hybrid/EV Battery Voltage Sensor "B" (CMC-02)	P0B40	open circuit	measured cell voltages of broken line and the next higher line in CMC-02	= 5.6	[V]	Battery CAN communication	active		1.5 [s] continuous	0 DCY
						CMC-02 error memory status flag	valid
						No internal communication error in CMC-02
Hybrid/EV Battery Voltage Sensor "B" (CMC-02)	P0B41	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-02 and ASIC voltage of CMC-02	> 1	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-02 and mean value (ASIC voltage of CMC-02 divided by number of cells in CMC-02)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "B" (CMC-02)	P0B41	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-02 and ASIC voltage of CMC-02	< -1	[V]	BECM mode	= AC_CHARGING		500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-02 and mean value (ASIC voltage of CMC-02 divided by number of cells in CMC-02)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "C" (CMC-03)	P0B48	circuit high	measured cell voltages in CMC-03	> 4.5	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-03 error memory status flag	valid
						No internal communication error in CMC-03
Hybrid/EV Battery Voltage Sensor "C" (CMC-03)	P0B47	circuit low	measured cell voltages in CMC-03	< 1	[V]	Battery CAN communication	active		1 [s] continuous	0 DCY
						CMC-03 error memory status flag	valid
						No internal communication error in CMC-03
Hybrid/EV Battery Voltage Sensor "C" (CMC-03)	P0B45	open circuit	measured cell voltages of broken line and the next higher line in CMC-03	= 5.6	[V]	Battery CAN communication	active		1.5 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						CMC-03 error memory status flag	valid
						No internal communication error in CMC-03	valid
Hybrid/EV Battery Voltage Sensor "C" (CMC-03)	P0B46	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-03 and ASIC voltage of CMC-03	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-03 and mean value (ASIC voltage of CMC-03 divided by number of cells in CMC-03)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "C" (CMC-03)	P0B46	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-03 and ASIC voltage of CMC-03	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-03 and mean value (ASIC voltage of CMC-03 divided by number of cells in CMC-03)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "D" (CMC-04)	P0B4D	circuit high	measured cell voltages in CMC-04	> 4.5	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-04 error memory status flag	valid
						No internal communication error in CMC-04
Hybrid/EV Battery Voltage Sensor "D" (CMC-04)	P0B4C	circuit low	measured cell voltages in CMC-04	< 1	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-04 error memory status flag	valid
						No internal communication error in CMC-04
Hybrid/EV Battery Voltage Sensor "D" (CMC-04)	P0B4A	open circuit	measured cell voltages of broken line and the next higher line in CMC-04	= 5.6	[V]	Battery CAN communication	active	1.5 [s] continuous	0 DCY
						CMC-04 error memory status flag	valid
						No internal communication error in CMC-04
Hybrid/EV Battery Voltage Sensor "D" (CMC-04)	P0B4B	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-04 and ASIC voltage of CMC-04	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-04 and mean value (ASIC voltage of CMC-04 divided by number of cells in CMC-04)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "D" (CMC-04)	P0B4B	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-04 and ASIC voltage of CMC-04	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-04 and mean value (ASIC voltage of CMC-04 divided by number of cells in CMC-04)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "E" (CMC-05)	P0B52	circuit high	measured cell voltages in CMC-05	> 4.5	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-05 error memory status flag	valid
						No internal communication error in CMC-05
Hybrid/EV Battery Voltage Sensor "E" (CMC-05)	P0B51	circuit low	measured cell voltages in CMC-05	< 1	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-05 error memory status flag	valid
						No internal communication error in CMC-05
Hybrid/EV Battery Voltage Sensor "E" (CMC-05)	P0B4F	open circuit	measured cell voltages of broken line and the next higher line in CMC-05	= 5.6	[V]	Battery CAN communication	active	1.5 [s] continuous	0 DCY
						CMC-05 error memory status flag	valid
						No internal communication error in CMC-05
Hybrid/EV Battery Voltage Sensor "E" (CMC-05)	P0B50	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-05 and ASIC voltage of CMC-05	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-05 and mean value (ASIC voltage of CMC-05 divided by number of cells in CMC-05)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "E" (CMC-05)	P0B50	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-05 and ASIC voltage of CMC-05	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-05 and mean value (ASIC voltage of CMC-05 divided by number of cells in CMC-05)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "F" (CMC-06)	P0B57	circuit high	measured cell voltages in CMC-06	> 4.5	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-06 error memory status flag	valid
						No internal communication error in CMC-06
Hybrid/EV Battery Voltage Sensor "F" (CMC-06)	P0B56	circuit low	measured cell voltages in CMC-06	< 1	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition	Monitoring Time Length	MIL Illumination
						CMC-06 error memory status flag	valid
						No internal communication error in CMC-06	valid
Hybrid/EV Battery Voltage Sensor "F" (CMC-06)	P0B54	open circuit	measured cell voltages of broken line and the next higher line in CMC-06	= 5.6	[V]	Battery CAN communication	active	1.5 [s] continuous	0 DCY
						CMC-06 error memory status flag	valid
						No internal communication error in CMC-06
Hybrid/EV Battery Voltage Sensor "F" (CMC-06)	P0B55	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-06 and ASIC voltage of CMC-06	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-06 and mean value (ASIC voltage of CMC-06 divided by number of cells in CMC-06)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "F" (CMC-06)	P0B55	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-06 and ASIC voltage of CMC-06	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-06 and mean value (ASIC voltage of CMC-06 divided by number of cells in CMC-06)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "G" (CMC-07)	P0B5C	circuit high	measured cell voltages in CMC-07	> 4.5	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-07 error memory status flag	valid
						No internal communication error in CMC-07
Hybrid/EV Battery Voltage Sensor "G" (CMC-07)	P0B5B	circuit low	measured cell voltages in CMC-07	< 1	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-07 error memory status flag	valid
						No internal communication error in CMC-07
Hybrid/EV Battery Voltage Sensor "G" (CMC-07)	P0B59	open circuit	measured cell voltages of broken line and the next higher line in CMC-07	= 5.6	[V]	Battery CAN communication	active	1.5 [s] continuous	0 DCY
						CMC-07 error memory status flag	valid
						No internal communication error in CMC-07
Hybrid/EV Battery Voltage Sensor "G" (CMC-07)	P0B5A	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-07 and ASIC voltage of CMC-07	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-07 and mean value (ASIC voltage of CMC-07 divided by number of cells in CMC-07)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "G" (CMC-07)	P0B5A	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-07 and ASIC voltage of CMC-07	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-07 and mean value (ASIC voltage of CMC-07 divided by number of cells in CMC-07)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "H" (CMC-08)	P0B61	circuit high	measured cell voltages in CMC-08	> 4.5	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-08 error memory status flag	valid
						No internal communication error in CMC-08
Hybrid/EV Battery Voltage Sensor "H" (CMC-08)	P0B60	circuit low	measured cell voltages in CMC-08	< 1	[V]	Battery CAN communication	active	1 [s] continuous	0 DCY
						CMC-08 error memory status flag	valid
						No internal communication error in CMC-08
Hybrid/EV Battery Voltage Sensor "H" (CMC-08)	P0B5E	open circuit	measured cell voltages of broken line and the next higher line in CMC-08	= 5.6	[V]	Battery CAN communication	active	1.5 [s] continuous	0 DCY
						CMC-08 error memory status flag	valid
						No internal communication error in CMC-08
Hybrid/EV Battery Voltage Sensor "H" (CMC-08)	P0B5F	circuit range/performance (rationality check high)	difference between sum of all cell voltages in CMC-08 and ASIC voltage of CMC-08	> 1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-08 and mean value (ASIC voltage of CMC-08 divided by number of cells in CMC-08)	> 1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Hybrid/EV Battery Voltage Sensor "H" (CMC-08)	P0B5F	circuit range/performance (rationality check low)	difference between sum of all cell voltages in CMC-08 and ASIC voltage of CMC-08	< -1	[V]	BECM mode	= AC_CHARGING	500 [ms] continuous	2 DCY
			OR				OR
			difference between any cell voltage in CMC-08 and mean value (ASIC voltage of CMC-08 divided by number of cells in CMC-08)	< -1	[V]	BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode	= HV_ON
Cell Module Controller (CMC) - Communication Monitoring

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
CMC-01: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-01: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-01 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-02: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-02: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-02 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-03: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-03: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-03 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-04: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-04: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-04 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-05: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-05: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-05 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-06: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-06: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-06 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-07: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-07: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-07 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-08: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-08: Communication	U0111	lost communication with Battery Energy Control Module "A"	message time out	detected		CMC-08 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-01: Communication	P0DAF	Hybrid/EV Battery Cell Balancing Circuit "A"	Bus-Off error of CMC-01 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-01: Communication	P0DAF	Hybrid/EV Battery Cell Balancing Circuit "A"	Bus-Off error of CMC-01 CAN controller	detected		CMC-01 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-02: Communication	P0DB3	Hybrid/EV Battery Cell Balancing Circuit "B"	Bus-Off error of CMC-02 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-02: Communication	P0DB3	Hybrid/EV Battery Cell Balancing Circuit "B"	Bus-Off error of CMC-02 CAN controller	detected		CMC-02 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-03: Communication	P0DB7	Hybrid/EV Battery Cell Balancing Circuit "C"	Bus-Off error of CMC-03 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-03: Communication	P0DB7	Hybrid/EV Battery Cell Balancing Circuit "C"	Bus-Off error of CMC-03 CAN controller	detected		CMC-03 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-04: Communication	P0DBB	Hybrid/EV Battery Cell Balancing Circuit "D"	Bus-Off error of CMC-04 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-04: Communication	P0DBB	Hybrid/EV Battery Cell Balancing Circuit "D"	Bus-Off error of CMC-04 CAN controller	detected		CMC-04 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-05: Communication	P0DBF	Hybrid/EV Battery Cell Balancing Circuit "E"	Bus-Off error of CMC-05 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-05: Communication	P0DBF	Hybrid/EV Battery Cell Balancing Circuit "E"	Bus-Off error of CMC-05 CAN controller	detected		CMC-05 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-06: Communication	P0DC3	Hybrid/EV Battery Cell Balancing Circuit "F"	Bus-Off error of CMC-06 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-06: Communication	P0DC3	Hybrid/EV Battery Cell Balancing Circuit "F"	Bus-Off error of CMC-06 CAN controller	detected		CMC-06 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-07: Communication	P0DC7	Hybrid/EV Battery Cell Balancing Circuit "G"	Bus-Off error of CMC-07 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-07: Communication	P0DC7	Hybrid/EV Battery Cell Balancing Circuit "G"	Bus-Off error of CMC-07 CAN controller	detected		CMC-07 error memory status flag	valid		1.5 [s] continuous	0 DCY
CMC-08: Communication	P0DCB	Hybrid/EV Battery Cell Balancing Circuit "H"	Bus-Off error of CMC-08 CAN controller	detected		Battery CAN communication	active		1.5 [s] continuous	0 DCY
CMC-08: Communication	P0DCB	Hybrid/EV Battery Cell Balancing Circuit "H"	Bus-Off error of CMC-08 CAN controller	detected		CMC-08 error memory status flag	valid		1.5 [s] continuous	0 DCY
Battery Energy Control Module (BECM) - Performance Monitoring
BECM: State of charge window monitoring	P057F	state of charge window monitoring as per CCR J1968.2	CASE 1: first monitoring cycle after changing from HV_OFF to HV_ON and driving cycle identified			BECM mode	= HV_ON		CASE 1:	2 DCY
			State of charge starts above the upper limit and stays outside	> 95	[%]				650 [s] once / DCY
			OR
			State of charge starts below the lower limit and stays outside	< 15	[%]				CASE 2:
			CASE 2: second and following monitoring cycles						5 [s] continuous
			State of charge starts above the upper limit and stays outside	> 95	[%]
			OR
			State of charge starts below the lower limit and stays outside	< 15	[%]
BECM: Performance monitoring based on resistance	P0A80	performance check as per CCR J1968.2 (based on resistance) on battery level	ratio between calculated battery resistance and Begin-Of-Life (BOL) resistance	> 2		average cell temperatures	< 50	[°C]	500 [s] continuous	2 DCY
							> -5	[°C]
						deviation between maximum and minimum cell temperature	< 10	[°C]
						battery current for calculation	< 0	[A]
						battery current	< -20	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.1	[-]
						gradient of battery current	< -1	[A/100ms]
						time after ECU startup	≥ 1.5	[s]
CMC-01: Performance Check based on capacity	P0A7F	performance check as per CCR J1968.2 (based on capacity) for CMC01	calculated capacity for CMC01	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-02: Performance Check based on capacity	P0EDD	performance check as per CCR J1968.2 (based on capacity) for CMC02	calculated capacity for CMC02	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-03: Performance Check based on capacity	P0EDE	performance check as per CCR J1968.2 (based on capacity) for CMC03	calculated capacity for CMC03	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-04: Performance Check based on capacity	P0EDF	performance check as per CCR J1968.2 (based on capacity) for CMC04	calculated capacity for CMC04	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-05: Performance Check based on capacity	P0EE0	performance check as per CCR J1968.2 (based on capacity) for CMC05	calculated capacity for CMC05	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-06: Performance Check based on capacity	P0EE1	performance check as per CCR J1968.2 (based on capacity) for CMC06	calculated capacity for CMC06	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-07: Performance Check based on capacity	P2CCC	performance check as per CCR J1968.2 (based on capacity) for CMC07	calculated capacity for CMC07	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-08: Performance Check based on capacity	P2CCD	performance check as per CCR J1968.2 (based on capacity) for CMC08	calculated capacity for CMC08	< 27.636	[Ah]	OCV-conditions fulfilled:			500 [ms] continuous	2 DCY
						battery current	< 1...3	[A]
						for time	= 7, 200...600	[s]
						runtime/EEPROM data are	valid	[-]
						difference of SOC between current and ultimate OCV measurement	≥ 60	[%]
						time between current and ultimate OCV measurement	< 4	[days]
						max. worst CASE Ah-accounting error	< 2	[%]
CMC-01: Performance Check	P0A7F	performance check as per CCR J1968.2 (based on resistance) for CMC01	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-02: Performance Check	P0EDD	performance check as per CCR J1968.2 (based on resistance) for CMC02	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-03: Performance Check	P0EDE	performance check as per CCR J1968.2 (based on resistance) for CMC03	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
CMC-03: Performance Check	P0EDE			> 2		average cell temperatures	< 50	[°C]	500 [s] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-04: Performance Check	P0EDF	performance check as per CCR J1968.2 (based on resistance) for CMC04	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-05: Performance Check	P0EE0	performance check as per CCR J1968.2 (based on resistance) for CMC05	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-06: Performance Check	P0EE1	performance check as per CCR J1968.2 (based on resistance) for CMC06	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-07: Performance Check	P2CCC	performance check as per CCR J1968.2 (based on resistance) for CMC07	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-08: Performance Check	P2CCD	performance check as per CCR J1968.2 (based on resistance) for CMC08	ratio between calculated cell resistance and Begin-Of-Live (BOL) resistance	> 2		battery current for cell selection	< -100	[A]	500 [s] continuous	2 DCY
						average cell temperatures	< 50	[°C]
							> -5	[°C]
						deviation between max. and min. cell temperature	< 5	[°C]
						battery current for calculation	< 0	[A]
						count of calculation ratios	= 100	[-]
						difference of minimum and maximum ratio between calculated resistance and begin of life resistance within a calculation set	≤ 0.15	[-]
						time after cell selection	≥ 1.5	[s]
						time after ECU startup	≥ 1.5	[s]
CMC-01: Balancing Check	P0DAC	balancing check per CCR J1968.2 for CMC01	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-02: Balancing Check	P0DB0	balancing check per CCR J1968.2 for CMC02	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-03: Balancing Check	P0DB4	balancing check per CCR J1968.2 for CMC03	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
CMC-03: Balancing Check	P0DB4	balancing check per CCR J1968.2 for CMC03		≥ 4	[Ah]	(BECM mode	OR		500 [ms] continuous	2 DCY

Table continues below

Component/System	Fault Code (SAE-Code)	Monitor Strategy Description	Malfunction Criteria	Threshold Value		Secondary Parameters	Enable Condition		Monitoring Time Length	MIL Illumination
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-04: Balancing Check	P0DB8	balancing check per CCR J1968.2 for CMC04	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-05: Balancing Check	P0DBC	balancing check per CCR J1968.2 for CMC05	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-06: Balancing Check	P0DC0	balancing check per CCR J1968.2 for CMC06	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-07: Balancing Check	P0DC4	balancing check per CCR J1968.2 for CMC07	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
CMC-08: Balancing Check	P0DC8	balancing check per CCR J1968.2 for CMC08	\| amount of electric charge of each cell - average amount of electric charge of all cells \|	≥ 4	[Ah]	(BECM mode	= HV_OFF		500 [ms] continuous	2 DCY
							OR
						BECM mode)	= LOCAL_ACTIVE
						absolute battery current	< 5	[A]
						OCV recovery time	≥ 11, 000...330	[s]
						cell state of charge	> 30	[%]
Battery Charger Control Module (BCCM) - Component errors
BCCM: Invalid Diagnostic Information	U113A	error memory status flag check	BCCM error memory status flag	not valid		(BECM mode	= AC_CHARGING		2.5 [s] continuous	2 DCY
							OR
						BECM mode	= EMERGENCY_OFF
							OR
						BECM mode	= HV_OFF
							OR
						BECM mode)	= HV_ON
						Hybrid CAN communication	active