Read Measuring Value Block, Function 08: Notes

Initiating Read Measuring Value Block

Indicated on display:

Rapid data transfer Help
Select function XX

-- Press buttons 0 and 8 to select "Read Measured Value Block" function 08.

Indicated on display:

Rapid data transfer Q
08 - Read measured value block

-- Press Q button to confirm input.

Indicated on display:

Read measured value block Help
Input display group number XXX

-- Input display group number (for example 001) by pressing the buttons and confirm by pressing the Q button.

The selected display group is displayed in standardized form.

Display Group 001


Read measuring value block 01			→	← Indicated on display
0 1 0 0	1 0 0	0 0 0 0	0 0 0 0
			X X X X	Rear lid: 1 = open, 0 = closed Luggage compartment light: 1 = light on, 0 = light off Switch for rear lid unlocking (not applicable): 1 = activated, 0 = not activated Motor for rear lid unlocking (not applicable): 1 = activated, 0 = motor not running
		X X X X	Actuator switch and/or interior switch on passenger's door: 00 = not activated, 01 = locking, 10 = unlocking, 11 = not permitted Actuator switch and/or interior switch on driver's door: 00 = not activated, 01 = locking, 10 = unlocking, 11 = not permitted
	X X X	Back door: 1 = open, 0 = closed Driver's and passenger's door: 1 = open, 0 = closed Engine hood: 1 = open, 0 = closed
X X X X	Key position in the lock cylinders Driver's/passenger's door, unlocking: 1 = key operated, 0 = key in center position Driver's/passenger's door, locking: 1 = key operated, 0 = key in center position Rear lid, unlocking: 1 = key operated, 0 = key in center position Rear lid, locking; 1 = key operated, 0 = key in center position

Display Group 002


Read measuring value block 02			→	← Indicated on display
0 1 0 0	0 1 0 0	0 0 0

		X X X	Terminal 15: 1 = ignition on, 0 = ignition off S-Contact: 1 = S-Contact on, 0 = S-Contact off Ground signal from radio: 1 = radio installed, 0 = radio removed
	X X X X	Radio-frequency operated remote unit "Open" button: 1 = activated, 0 = not activated Radio-frequency operated remote unit "Close" button: 1 = activated, 0 = not activated Radio-frequency operated remote unit "Rear lid" button: 1 = activated, 0 = not activated (not applicable) Radio-frequency operated remote unit "Panic" button (USA only): 1 = activated, 0 = not activated
X X X X	Interior light control: 1 = interior light on, 0 = interior light off Control wire for power window/sunroof: 1 = terminal 87 (holding the voltage supply), 0 = Ground (GND) "Comfort closing" : 1 = comfort closing activated, 0 = not activated "Comfort opening" function: 1 = comfort opening activated, 0 = not activated

Display Group 003

Read measuring value block 03

→

← Indicated on display

0 0 0 1

0 0 0 0

X X X X

Radio-frequency operated remote unit "Open" button ⁽¹⁾: 1 = activated, 0 = not activated
Radio-frequency operated remote unit "Close" button ⁽¹⁾: 1 = activated, 0 = not activated
Radio-frequency operated remote unit "Rear lid" button ⁽¹⁾: (not applicable) 1 = activated, 0 = not activated
Radio-frequency operated remote unit "Panic" button ⁽¹⁾: (USA only) 1 = activated, 0 = not activated

X X X X

Radio-frequency operated remote control memory address 4 ⁽²⁾: 1 = location assigned, 0 = not assigned
Radio-frequency operated remote control memory address 3 ⁽²⁾: 1 = location assigned, 0 = not assigned
Radio-frequency operated remote control memory address 2 ⁽²⁾: 1 = location assigned, 0 = not assigned
Radio-frequency operated remote control memory address 1 ⁽²⁾: 1 = location assigned, 0 = not assigned

⁽¹⁾	This display group also shows un-coded radio-frequency operated remote units (e.g. for a check of the remote unit).

⁽²⁾	If you operate radio-frequency operated remote unit, corresponding remote control memory address blinks.