LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Audi >> 2025 >> Q5 e Premium Plus >> Repair and Diagnosis >> Engine Performance >> System >> Generic Scan Tool (DSMA) (Transmission - Battery Charger Control Module DTC Tables) >> St Generic Scan Tool >> Diagnosis And Testing >> Transmission DTC Tables >> Transmission Control Module -- DL382E - 7A (7 SPEED) 0CJC, 2025 MY
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Transmission Control Module -- DL382E - 7A (7 SPEED) 0CJC, 2025 MY

Component / System DTC / DTC Description Monitor Strategy Description Malfunction Criteria Threshold Value Secondary Parameters Enable Conditions Monitoring Time Length MIL Illum.
Gear Shift Module 1-3 P2832 - Shift Fork "A" Position Circuit Range/Performance Signal range check Duty-Cycle of Position sensor > 92.5 [%] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Duty-Cycle of Position sensor < 7.5 [%]          
Gear Shift Module 4-6 P2841 - Shift Fork "D" Position Circuit Range/Performance Signal range check Duty-Cycle of Position sensor > 92.5 [%] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Duty-Cycle of Position sensor < 7.5 [%]          
Gear Shift Module 5-7 P283C - Shift Fork "C" Position Circuit Range/Performance Signal range check Duty-Cycle of Position sensor > 92.5 [%] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Duty-Cycle of Position sensor < 7.5 [%]          
Gear Shift Module 2-R P2837 - Shift Fork "B" Position Circuit Range/Performance Signal range check Duty-Cycle of Position sensor > 92.5 [%] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Duty-Cycle of Position sensor < 7.5 [%]          
Gear Shift Module 1-3 P2831 - Shift Fork "A" Position Circuit Signal range check No signal received for > 1 [s]     [-] 2 [s] Continuous 2 DCY
Gear Shift Module 4-6 P2840 - Shift Fork "D" Position Circuit Signal range check No signal received for > 1 [s]     [-] 2 [s] Continuous 2 DCY
Gear Shift Module 5-7 P283B - Shift Fork "C" Position Circuit Signal range check No signal received for > 1 [s]     [-] 2 [s] Continuous 2 DCY
Gear Shift Module 2-R P2836 - Shift Fork "B" Position Circuit Signal range check No signal received for > 1 [s]     [-] 2 [s] Continuous 2 DCY
Gear Shift Module 1-3 P2832 - Shift Fork "A" Position Circuit Range/Performance Signal range check Time of oscillation < 0.9 [ms] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Time of oscillation > 1.1 [ms]          
Gear Shift Module 4-6 P2841 - Shift Fork "D" Position Circuit Range/Performance Signal range check Time of oscillation < 0.9 [ms] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Time of oscillation > 1.1 [ms]          
Gear Shift Module 5-7 P283C - Shift Fork "C" Position Circuit Range/Performance Signal range check Time of oscillation or < 0.9 [ms] Sensor supply voltage 4.5•••5.5 [V] 2 [s] Continuous 2 DCY
  Time of oscillation > 1.1 [ms]          
Gear Shift Module 2-R P2837 - Shift Fork "B" Position Circuit Range/Performance Signal range check Time of oscillation < 0.9 [ms] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Time of oscillation > 1.1 [ms]          
Speed Sensor Shaft 1 P0718 - Input/Turbine Shaft Speed Sensor "A" Circuit Intermittent Rationality check No signal > 1 [s] Ignition On [-] 2 [s] Continuous 2 DCY
Speed Sensor Shaft 2 P2768 - Input/Turbine Shaft Speed Sensor "B" Circuit Intermittent Rationality check No signal > 1 [s] Ignition On [-] 2 [s] Continuous 2 DCY
Speed Sensor Shaft 1 P0501 - Vehicle Speed Sensor "A" Circuit Range/Performance Rationality check Difference between measured > 150 [rpm] Input shaft speeds for shafts 1 > 100 [rpm] 2 [s] 2 DCY
  and calculated output speed for     and 2     Continuous  
  shaft 1 and Difference between output shaft > 150 [rpm]          
  speed 1 and shaft 2              
Speed Sensor Shaft 2 P2159 - Vehicle Speed Sensor "B" Circuit Range/Performance Rationality check Difference between measured > 150 [rpm] Input shaft speeds for shafts 1 > 100 [rpm] 2 [s] 2 DCY
  and calculated output speed for     and 2     Continuous  
  shaft 2 and Difference between output shaft > 150 [rpm]          
  speed 1 and shaft 2              
Speed Sensor Shaft 1 and P2162 - Vehicle Speed Sensor "A"/"B" Correlation Rationality check Difference between output shaft > 150 [rpm] Input shaft speeds for shafts 1 > 100 [rpm] 2 [s] 2 DCY
Shaft 2   speeds and input speeds shafts 1     and 2     Continuous  
  and 2     and Engaged gear position is not Neutral [-]    
TCM Temperature Sensor P0666 - Control Module Internal Temperature Sensor "A" Circuit Circuit continuity HW-Fehler Detected [-] Ignition On [-] 2 [s] 2 DCY
check             Continuous  
  or Control Module Internal Sensor <-45 [°C]          
  Signal (in Basis-SW) or Control Module Internal Sensor >160 [°C]          
  Signal (in Basis-SW) or SPI-Fehler Detected [-] and TCM Temperature Sensor Finished [-]    
        Initialization        
Circuit continuity TCM Temperature Sensor at -0.03125 [°C] Ignition On [-] 33 [s] 2 DCY
check             Continuous  
        and        
        TCM Temperature Sensor Finished [-]    
        Initialization        
P0667 - Control Module Internal Temperature Sensor "A" Range/Performance Rationality check Difference between actual TCM Temperature Sensor and filtered temperatur > 8 [°C] Ignition On [-] 2 [s] Continuous 2 DCY
P0713 - Transmission Fluid Temperature Sensor "A" Circuit High Circuit continuity check Short circuit to high > 4.7 [V] Power supply voltage 6•••18 [V] 2 [s] Continuous 2 DCY
P0712 - Transmission Fluid Temperature Sensor "A" Circuit Low Circuit continuity check Short circuit to ground < 0.16 [V] Power supply voltage 6•••18 [V] 2 [s] Continuous 2 DCY
P0711 - Transmission Fluid Temperature Sensor "A" Circuit Range/Performance Rationality check Actual ATF temperature > 170 [°C] Power supply voltage 6•••18 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Actual ATF temperature < -50 [°C]          
Circuit continuity check Difference between actual ATF temperature and filtered temperatur > 15 [°C] Power supply voltage 6•••18 [V] 2 [s] Continuous 2 DCY
ATF Pump Speed Sensor P0C2D - Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal Low Signal range check Sensor output voltage < 0.25 [V] Sensor supply voltage 4.5•••5.5 [V] 2 [s] Continuous 2 DCY
P0C2E - Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal High Signal range check Sensor output voltage > 4.5 [V] Sensor supply voltage 4.5•••5.5 [V] 2 [s] Continuous 2 DCY
P0C2C - Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal Range/Performance Rationality check Sensor output sin2 +cos2 > 0.8 [-] Sensor supply voltage 4.5•••5.5 [V] 2 [s] 2 DCY
              Continuous  
  or              
  Sensor output sin2 +cos2 < 1.2 [-]          
TCM Temperature Sensor P0711 - Transmission Fluid Temperature Sensor "A" Circuit Range/Performance Rationality check Difference between ATF temperature and TCM temperature > 20 [K] Deviation between temperature measured at the transmission control module (TCM) printed circuit board (PCB) and temperature measured in automatic transmission fluid (ATF) oil after a longer term of transmission cool down. Too high [-] 0.0 [s] Once / DCY 2 DCY
Electrical Pump P1A7D - Electr. pump 3 for transmission Temperature implausible Rationality Check The ATF auxiliary pump Invalid [-] LIN communication Active [-] 5 [s] 2 DCY
  temperature signal           Continuous  
        and        
        Temperature sensor error flag Not set [-]    
Supply Voltage Monitoring P06D5 - Sensor Reference Voltage "E" Circuit Range/Performance Signal range check Internal sensor supply voltage > 5.5 [V]     [-] 2 [s] 2 DCY
Stage 3           Continuous  
  or          
  Internal sensor supply voltage < 4.5 [V]      
(Electrical) ATF Pump P0C2A - Electric/Auxiliary Transmission Fluid Pump Motor Stalled Functional check Current ATF pump speed 300 [rpm] ATF pump governor Enabled   2 [s] 2 DCY
              Continuous  
  and     and        
  Set current for ATF pump control 30•••50 [A] Target ATF-engine speed 300 [rpm]    
P0B0D - Electric/Auxiliary Transmission Fluid Pump Motor Control Module Signal range check Difference between actual and commanded ATF pump speed > 500 [rpm] Calibration Not active [-] 2 [s] Continuous 2 DCY
P0C28 - Electric/Auxiliary Transmission Fluid Pump Motor Current High Functional check ATF pump overcurrent protection active [-] Ignition On [-] 2 [s] Continuous 2 DCY
(Electrical) ATF Pump Control Module P0C29 - Electric/Auxiliary Transmission Fluid Pump Driver Circuit Performance Circuit continuity check electrical failure in power amplifier Detected [-]     [-] 2 [s] Continuous 2 DCY
Circuit continuity check Driver error Detected [-]     [-] 2 [s] Continuous 2 DCY
Circuit continuity check Overload ATF pump Detected [-]     [-] 2 [s] Continuous 2 DCY
Solenoid for gear 1-3 P0750 - Shift Solenoid "A" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for gear 4-6 P0765 - Shift Solenoid "D" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for gear 5-7 P0760 - Shift Solenoid "C" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for gear 2-R P0755 - Shift Solenoid "B" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for clutch 1 P0745 - Pressure Control Solenoid "A" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for clutch 2 P0775 - Pressure Control Solenoid "B" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for main pressure P0795 - Pressure Control Solenoid "C" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for cooling P0770 - Shift Solenoid "E" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for overpressure P2706 - Shift Solenoid "F" Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
reduction check and measured current.     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Solenoid for disconnect clutch P287F - Engine Disconnect Clutch Actuator Circuit Range/Performance Circuit continuity Difference between set current > 100 [mA] Circuits for activation and Active [-] 2 [s] 2 DCY
check and measured current     deactivation of the transmission     Continuous  
        solenoid driver (SDS4)        
        actuators and No transmission solenoid driver Detected [-]    
        (SDS4) error and Belonging common high side Active [-]    
        switch        
Gear Actuator 1-3 P284D - Shift Fork "A" Unrequested Movement Functional check Loaded gear leaves the engage- position > 3 [mm] Gear actuator 1-3 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P2850 - Shift Fork "D" Unrequested Movement Functional check Loaded gear leaves the engage- position > 3 [mm] Gear actuator 4-6 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P284F - Shift Fork "C" Unrequested Movement Functional check Loaded gear leaves the engage- position > 3 [mm] Gear actuator 5-7 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P284E - Shift Fork "B" Unrequested Movement Functional check Loaded gear leaves the engage- position > 3 [mm] Gear actuator 2-R nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P187A - Gear selector 1 Engaging process not successful Functional check Time out in gear actuator state after synchronization > 1 [s] Gear actuator 1-3 nominal state is After syncronization [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P187D - Gear selector 4 Engaging process not successful Functional check Time out in gear actuator state after synchronization > 1 [s] Gear actuator 4-6 nominal state is After syncronization [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P187C - Gear selector 3 Engaging process not successful Functional check Time out in gear actuator state after synchronization > 1 [s] Gear actuator 5-7 nominal state is After syncronization [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P187B - Gear selector 2 Engaging process not successful Functional check Time out in gear actuator state after synchronization > 1 [s] Gear actuator 2-R nominal state is After syncronization [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P187A - Gear selector 1 Engaging process not successful Functional check Time out in gear actuator state Unlatched > 1 [s] Gear actuator 1-3 nominal state is Unlatched [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P187D - Gear selector 4 Engaging process not successful Functional check Time out in gear actuator state Unlatched > 1 [s] Gear actuator 4-6 nominal state is Unlatched [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P187C - Gear selector 3 Engaging process not successful Functional check Time out in gear actuator state Unlatched > 1 [s] Gear actuator 5-7 nominal state is Unlatched [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P187B - Gear selector 2 Engaging process not successful Functional check Time out in gear actuator state Unlatched > 1 [s] Gear actuator 2-R nominal state is Unlatched [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P187A - Gear selector 1 Engaging process not successful Functional check Time out in gear actuator state Unlatched > 1 [s] Gear actuator 1-3 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P187D - Gear selector 4 Engaging process not successful Functional check Time out in gear actuator state Engage > 1 [s] Gear actuator 4-6 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P187C - Gear selector 3 Engaging process not successful Functional check Time out in gear actuator state Engage > 1 [s] Gear actuator 5-7 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P187B - Gear selector 2 Engaging process not successful Functional check Time out in gear actuator state Engage > 1 [s] Gear actuator 2-R nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P2845 - Shift Fork "A" Position Sensor Incorrect Neutral Position Indicated Functional check Gear actuator 1-3 leaves the neutral-position > 3 [mm] Gear actuator 1-3 nominal state is Neutral [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P2848 - Shift Fork "D" Position Sensor Incorrect Neutral Position Indicated Functional check Gear actuator 4-6 leaves the neutral-position > 3 [mm] Gear actuator 4-6 nominal state is Neutral [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P2847 - Shift Fork "C" Position Sensor Incorrect Neutral Position Indicated Functional check Gear actuator 5-7 leaves the neutral-position > 3 [mm] Gear actuator 5-7 nominal state is Neutral [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P2846 - Shift Fork "B" Position Sensor Incorrect Neutral Position Indicated Functional check Gear actuator 2-R leaves the neutral-position > 3 [mm] Gear actuator 2-R nominal state is Neutral [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P284D - Shift Fork "A" Unrequested Movement Functional check Gear actuator 1-3 leaves the engage-position > 1 [s] Gear actuator 1-3 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P2850 - Shift Fork "D" Unrequested Movement Functional check Gear actuator 4-6 leaves the engage-position > 1 [s] Gear actuator 4-6 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P284F - Shift Fork "C" Unrequested Movement Functional check Gear actuator 5-7 leaves the engage-position > 1 [s] Gear actuator 5-7 nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P284E - Shift Fork "B" Unrequested Movement Functional check Gear actuator 2-R leaves the engage-position > 1 [s] Gear actuator 2-R nominal state is Engaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P2849 - Shift Fork "A" Stuck Functional check Time out in gear actuator state Disengage > 2 [s] Gear actuator 1-3 nominal state is Disengaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P284C - Shift Fork "D" Stuck Functional check Time out in gear actuator state Disengage > 2 [s] Gear actuator 4-6 nominal state is Disengaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P284B - Shift Fork "C" Stuck Functional check Time out in gear actuator state Disengage > 2 [s] Gear actuator 5-7 nominal state is Disengaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P284A - Shift Fork "B" Stuck Functional check Time out in gear actuator state Disengage > 2 [s] Gear actuator 2-R nominal state is Disengaged [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P187A - Gear selector 1 Engaging process not successful Functional check Time out in gear actuator state Synchronise > 2 [s] Gear actuator 1-3 nominal state is Synchronized [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P187D - Gear selector 4 Engaging process not successful Functional check Time out in gear actuator state Synchronise > 2 [s] Gear actuator 4-6 nominal state is Synchronized [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P187C - Gear selector 3 Engaging process not successful Functional check Time out in gear actuator state Synchronise > 2 [s] Gear actuator 5-7 nominal state is Synchronized [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P187B - Gear selector 2 Engaging process not successful Functional check Time out in gear actuator state Synchronise > 2 [s] Gear actuator 2-R nominal state is Synchronized [-] 2 [s] Continuous 2 DCY
Drive-Off Clutch 1 P0811 - Excessive Clutch "A" Slippage Functional check Clutch slippage was detected > 150 [rpm] Clutch state is Drive [-] 2 [s] Continuous 2 DCY
Drive-Off Clutch 2 P081E - Excessive Clutch "B" Slippage Functional check Clutch slippage was detected > 150 [rpm] Clutch state is Drive [-] 2 [s] Continuous 2 DCY
Speed Sensor Shaft 1 P0716 - Input/Turbine Shaft Speed Sensor "A" Circuit Range/Performance Signal range check Input shaft speed for shaft 1 > 12000 [rpm]     [-] 2 [s] Continuous 2 DCY
Speed Sensor Shaft 2 P2766 - Input/Turbine Shaft Speed Sensor "B" Circuit Range/Performance Signal range check Input shaft speed for shaft 2 > 12000 [rpm]     [-] 2 [s] Continuous 2 DCY
Solenoid for gear 1-3 P0753 - Shift Solenoid "A" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 1 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 1 and Common low side for the magnetic valve 1 and Electric current of the magnetic valve 1 or Error at the magnetic valve 1 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for gear 5-7 P0763 - Shift Solenoid "C" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 3 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 3 and Common low side for the magnetic valve 3 and Electric current of the magnetic valve 3 or Error at the magnetic valve 3 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for clutch 1 P0748 - Pressure Control Solenoid "A" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 1 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 1 and Common low side for the magnetic valve 1 and Electric current of the magnetic valve 1 or Error at the magnetic valve 1 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for overpressure reduction P2709 - Shift Solenoid "F" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 6 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 6 and Common low side for the magnetic valve 6 and Electric current of the magnetic valve 6 or Error at the magnetic valve 6 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for gear 2-R P0758 - Shift Solenoid "B" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 2 and transmission solenoid driver (SDS4) test sequence for the the magnetic valve 2 and Common low side for the magnetic valve 2 and Electric current of the magnetic valve 2 or Error at the magnetic valve 2 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for gear 4-6 P0768 - Shift Solenoid "D" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 3 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 3 and Common low side for the magnetic valve 3 and Electric current of the magnetic valve 3 or Error at the magnetic valve 3 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for clutch 2 P0778 - Pressure Control Solenoid "B" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 2 and transmission solenoid driver (SDS4) test sequence for the the magnetic valve 2 and Common low side for the magnetic valve 2 and Electric current of the magnetic valve 2 or Error at the magnetic valve 2 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for disconnect clutch P2880 - Engine Disconnect Clutch Actuator Circuit Low Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 2 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 2 and Common low side for the magnetic valve 2 and Electric current of the magnetic valve 2 or Error at the magnetic valve 2 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for main pressure P0798 - Pressure Control Solenoid "C" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 3 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 3 and Common low side for the magnetic valve 3 and Electric current of the magnetic valve 3 or Error at the magnetic valve 3 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
Solenoid for cooling P0773 - Shift Solenoid "E" Electrical Circuit continuity check Internal voltage Failure [-] Hardware module to control the magnetic valve 5 and transmission solenoid driver (SDS4) test sequence for the magnetic valve 5 and Common low side for the magnetic valve 5 and Electric current of the magnetic valve 5 or Error at the magnetic valve 5 Ready Finished Active >= 200 Detected [-] [-] [-] [mA] [-] 2 [s] Continuous 2 DCY
TCM internal driver A P0702 - Transmission Control System Electrical Circuit continuity check Internal voltage Failure [-] transmission solenoid driver (SDS4) A monitoring and Error in the supply voltage of the transmission solenoid driver (SDS4) A and State of the transmission solenoid driver (SDS4) A switch off path Active Not detected Active [-] [-] [-] 2 [s] Continuous 2 DCY
TCM internal driver B Circuit continuity check Internal voltage Failure [-] transmission solenoid driver (SDS4) B monitoring and Error in the supply voltage of the transmission solenoid driver (SDS4) B and State of the transmission solenoid driver (SDS4) B switch off path Active Not detected Active [-] [-] [-] 2 [s] Continuous 2 DCY
TCM internal driver C Circuit continuity check Internal voltage Failure [-] transmission solenoid driver (SDS4) C monitoring and Error in the supply voltage of the transmission solenoid driver (SDS4) C and State of the transmission solenoid driver (SDS4) C switch off path Active Not detected Active [-] [-] [-] 2 [s] Continuous 2 DCY
TCM P0700 - Transmission Control System (MIL Request) Functional check Central processing unit (CPU) permanent shutdown of all actors Detected [-]     [-] 2 [s] Continuous 2 DCY
P062F - Internal Control Module EEPROM Error Rationality check Comparison of EEProm date - both copies Invalid [-] Reading operation of datablock Active [-] 2 [s] Continuous 2 DCY
Memory check Comparison of stored value - both copies Invalid [-] Reading operation of datablock Active [-] 2 [s] Continuous 2 DCY
Memory check Write ability check Failed [-]     [-] 2 [s] Continuous 2 DCY
P0701 - Transmission Control System Range/Performance Functional check Repeated malfunctions at switch off path check (SOPC) Detected [-]       2 [s] Once / DCY 2 DCY
Supply Voltage Monitoring Stage 1 P0560 - System Voltage Signal range check Internal sensor supply voltage or Internal sensor supply voltage > 5.5 < 4.5 [V] [V]     [-] 2 [s] Continuous 2 DCY
Supply voltage Monitoring Stage 2 Signal range check Internal sensor supply voltage or Internal sensor supply voltage > 5.5 < 4.5 [V] [V]     [-] 2 [s] Continuous 2 DCY
TCM internal driver A P06A6 - Sensor Reference Voltage "A" Circuit Range/Performance Circuit continuity check Internal error flag on solenoid driver A is Set [-] Transmission solenoid driver (SDS4) A monitoring Active [-] 2 [s] Continuous 2 DCY
TCM internal driver B P06A7 - Sensor Reference Voltage "B" Circuit Range/Performance Circuit continuity check Internal error flag on solenoid driver B is Set [-] Transmission solenoid driver (SDS4) B monitoring Active [-] 2 [s] Continuous 2 DCY
TCM internal driver C P06A8 - Sensor Reference Voltage "C" Circuit Range/Performance Circuit continuity check Internal error flag on solenoid driver C is Set [-] Transmission solenoid driver (SDS4) C monitoring Active [-] 2 [s] Continuous 2 DCY
Supply Voltage Monitoring P06A9 - Sensor Reference Voltage "D" Circuit Range/Performance Signal range check Internal sensor supply voltage < 4.8 [V]     [-] 2 [s] Continuous 2 DCY
P0562 - System Voltage Low Signal range check Supply Voltage and one of the following monitors P0750, P0765, P0760, P0755, P0745, P0775, P0795, P0770, P2706 protective function is < 8 Active [V] [-]     [-] 5 [s] Continuous 2 DCY
U358F - Control Module Internal Voltage Sensor "A" Circuit Rationality check Internal supply voltage difference or Internal supply voltage difference < -2.6 >= 3.5 [V]     [-] 5 [s] Continuous 2 DCY
(Electrical) ATF Pump P0B0A - Electric/Auxiliary Transmission Fluid Pump Motor Supply Voltage Circuit Low Signal range check Supply Voltage and P0B0D protective function is < 10 Active [V] [-] Ignition On [-] 2 [s] Continuous 2 DCY
Supply Voltage Monitoring P0563 - System Voltage High Signal range check Supply Voltage > 18 [V]     [-] 2 [s] Continuous 2 DCY
FlexRay U0110 - Lost Communication With Drive Motor Control Module "A" Communication check Messages from Drive Motor Control Module "A" Not Received [-] Ignition On [-] 2 [s] Continuous 2 DCY
U0151 - Lost Communication With Restraints Control Module Communication check Communication with restraints control module Failed [-] Ignition On [-] 2 [s] Continuous 2 DCY
Electric Clutch Between Engine And Drive Motor P2882 - Engine Disconnect Clutch Excessive Slippage Functional check Torque reduction for combustion engine due to slip at hybrid clutch below a certain value of max torque < 80 [%] Ignition On [-] 5 [s] Continuous 2 DCY
P2886 - Engine Disconnect Clutch Stuck Closed Functional check Internal combustion engine speed despite open commanded hybrid clutch, internal combustion engine speed integral higher than a certain value > 30 [rpm*s ] Adaption of electric clutch between engine and drive motor Not active [-] 2 [s] Continuous 2 DCY
Solenoid for clutch 1 P0747 - Pressure Control Solenoid "A" Stuck On Functional check Difference in actual pressure on clutch K1 compared to the requested pressure on clutch K1 Detected [-]     [-] 2 [s] Continuous 2 DCY
Solenoid for clutch 2 P0777 - Pressure Control Solenoid "B" Stuck On Functional check Difference in actual pressure on clutch K2 compared to the requested pressure on clutch K2 Detected [-]     [-] 2 [s] Continuous 2 DCY
TCM P060B - Internal Control Module A/D Processing Performance Rationality check Repeated implausible sensor signal Detected [-]     [-] 2 [s] Continuous 2 DCY
TCM Safety monitor P0607 - Control Module Performance Functional check Traction in the opposite driving direction Detected [-]     [-] 2 [s] Continuous 2 DCY
Functional check Selection of too low gear and clutch Detected Closed [-] [-]     [-] 2 [s] Continuous 2 DCY
Functional check Selection of too low gear Detected [-]     [-] 2 [s] Continuous 2 DCY
Rationality check A very low gear and abnormal deceleration due to the hybrid clutch being Engaged Closed [-] [-]     [-] 2 [s] Continuous 2 DCY
TCM P2C83 - Cold Start Shift Time Too Short Functional check Engine minimum speed requirement, sent from Engine Control Modul (ECM) to Transmission Control Module (TCM) during cold start Not satisfied [-] No transmission malfunction that reduces the available gears and gear selection is and a minimum speed requirement caused by Cold Start Emission Reduction Strategy (CSERS) by Transmission Control Module (TCM) is Detected D or S Received [-] [-] [-] Once / DCY 2 DCY
P0895 - Shift Time Too Short Functional check Engine minimum speed requirement, sent from Engine Control Module (ECM) to Transmission Control Module (TCM) because of an OBD relevant measure (not Cold Start Emission Reduction Strategy (CSERS)) Not satisfied [-] No transmission malfunction that reduces the available gears and gear selection is and a minimum speed requirement caused by an OBD relevant measure (not Cold Start Emission Reduction Strategy (CSERS)) by Transmission Control Module (TCM) is Detected D or S Received [-] Multiple 2 DCY
Electric Clutch Between Engine And Drive Motor P0A0F - Engine Failed to Start Functional check Number of moment increases and K0 clutch temperature and failure flag engine torque and failure flag clutch too high too high Active Active [-] [-] [-] [-] Hybrid clutch K0 charging state or Hybrid clutch K0 dragstart state and no combustion engine speed Active Active Detected [-] [-] [-] 2 [s] Continuous 2 DCY
TCM Safety monitor P0607 - Control Module Performance Functional check Engagement of two gears on one shaft Detected [-]     [-] 2 [s] Continuous 2 DCY
Electrical Pump P195F - Electr. pump 3 for transmission Supply voltage too low Rationality check Test for supply voltage too low Failed [-] Ignition and LIN-communication error and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and power supply voltage On Not active On 8•••18 [-] [-] [-] [V] 5 [s] Continuous 2 DCY
P196A - Electr. pump 3 for transmission Supply voltage too high Rationality check Test for supply voltage too low Failed [-] Ignition and LIN-communication error and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and power supply voltage On Not active On 8•••18 [-] [-] [-] [V] 0...5 [s] Continuous 2 DCY
U13E9 - Electr. pump 3 for transmission no communication Communication check Pump communication Failed [-] Ignition and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and power supply voltage On On 8•••18 [-] [-] [V] 0...5 [s] Continuous 2 DCY
P196B - Electr. pump 3 for transmission No function Functional check Parameter set or Overcurrent check or Rotor Wrong Failed Blocked [-] [-] [-] Ignition and LIN-communication error and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and power supply voltage On Not active On 8•••18 [-] [-] [-] [V] 0...5 [s] Continuous 2 DCY
P196C - Electr. pump 3 for transmission Mechanical malfunction Functional check MosFET or Controller or Watchdog Defect Defect Error [-] [-] [-] Ignition and Functional fault and LIN communication error On Not active Not active [-] [-] [-] 0...5 [s] Continuous 2 DCY
  or Temperature sensor or Position sensor Defect Defect [-] [-] and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and Power supply voltage On 8•••18 [-] [V]    
P196B - Electr. pump 3 for transmission No function Functional check Test for speed Failed [-] Ignition and Functional fault and Hardware malfunction and Overtemperature and LIN communication error and Automatic Transmission Fluid Pump 2 (ATFP2-pump) and Power supply voltage On Not Active Not Active Not Active Not Active On 8•••18 [-] [-] [-] [-] [-] [-] [V] 0...5 [s] Continuous 2 DCY
TCM P1A7E - Activation of electrical pump 3 for transmission oil No function Circuit continuity Check Short circuit of Automatic Transmission Fluid Pump 2 (ATFP2-pump) Pump-On-Pin to Low Detected [-] Ignition On [-] 2 [s] Continuous 2 DCY
Circuit continuity Check Short circuit of Automatic Transmission Fluid Pump 2 (ATFP2-pump) Pump-On-Pin to High Detected [-] Ignition On [-] 2 [s] Continuous 2 DCY
Electrical Pump P1A7D - Electr. pump 3 for transmission Temperature implausible Rationality check ATF auxiliary pump temperature signal Implausible [-] Ignition and Deviation between temperature transmitted by ATF auxiliary pump (via LIN) and temperature measured within the TCU after a longer term of transmission cool down On Too high [-] [-] 0 [s] Once / DCY 2 DCY
TCM Safety monitor P0607 - Control Module Performance Functional check Closure of both clutches Detected [-]     [-] 2 [s] Continuous 2 DCY
Functional check Incorrect clutch actuation Detected [-]     [-] 2 [s] Continuous 2 DCY
Flexray U0080 - Vehicle Communication Bus F Communication check No Flexray synchronisation Detected [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from ECM U0100 - Lost Communication With ECM/PCM "A" Communication check Engine Control Module No signal [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from ABS U0121 - Lost Communication With Anti-Lock Brake System (ABS) Control Module "A" Communication check Anti-Lock Brake System No signal [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from ECM U0401 - Invalid Data Received From ECM/PCM "A" Communication check Data received from Engine Control Module Invalid [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from ABS U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A" Communication check Data received from Anti-Lock Brake System Invalid [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from ECM P0614 - ECM/TCM Incompatible Rationality check Information of engine code Faulty [-] Ignition On [-] 2 [s] Continuous 2 DCY
Rationality check Information of transmission code Faulty [-] Ignition On [-] 2 [s] Continuous 2 DCY
Flexray Signal from gear shift control module U0103 - Lost Communication With Gear Shift Control Module "A" Communication check Messages from Shift by wire control module Not received [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
U0404 - Invalid Data Received From Gear Shift Control Module "A" Communication check Data Received from Gear Shift Control Module is Invalid [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
TCM U1103 - Production mode active Functional check Production mode active [-] Ignition On [-] 2 [s] Continuous 2 DCY
Gear Actuator 1-3 P187A - Gear selector 1 Engaging process not successful Functional check Difference between measured and synchronised shaft speed 1 and gear actuator 1-3 movement or gear actuator 1-3 movement > 300 > 7 < -7 [rpm] [mm] [mm] Shaft 1 and 2 In sync position [-] 2 [s] Continuous 2 DCY
Gear Actuator 4-6 P187D - Gear selector 4 Engaging process not successful Functional check Difference between measured and synchronised shaft speed 2 and gear actuator 4-6 movement or gear actuator 4-6 movement > 300 > 7 < -7 [rpm] [mm] [mm] Shaft 1 and 2 In sync position [-] 2 [s] Continuous 2 DCY
Gear Actuator 5-7 P187C - Gear selector 3 Engaging process not successful Functional check Difference between measured and synchronised shaft speed 1 and gear actuator 5-7 movement or gear actuator 5-7 movement > 300 > 7 < -7 [rpm] [mm] [mm] Shaft 1 and 2 In sync position [-] 2 [s] Continuous 2 DCY
Gear Actuator 2-R P187B - Gear selector 2 Engaging process not successful Functional check Difference between measured and synchronised shaft speed 2 and gear actuator 2-R movement or gear actuator 2-R movement > 300 > 7 < -7 [rpm] [mm] [mm] Shaft 1 and 2 In sync position [-] 2 [s] Continuous 2 DCY
Gear shift control module P0919 - Gear Shift Position Control Error Rationality check Flexray signal initialisation errorflag from Shift by wire control module is set [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
P0915 - Gear Shift Position Circuit "A" Range/Performance Rationality check Handshake from Shift by wire control module failed [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
Rationality check Flexray signal position from Shift by wire control module is invalid [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
P0919 - Gear Shift Position Control Error Rationality check Flexray invalid signal position from Shift by wire control module is detected [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
U0304 - Software Incompatibility With Gear Shift Control Module "A" Rationality check Shift by wire control module variant is incorrect [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
P085D - Gear Shift Control Module "A" Performance Rationality check Flexray signal position from Shift by wire control module error value is detected [-] Ignition (KL15) not equal and Battery voltage 0 9•••17 [V] [V] 2 [s] Continuous 2 DCY
Flexray Signal from ABS C0501 - Left Front Wheel Speed Sensor "A" Range/Performance Signal range check Front left wheel speed sensor signal Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C0507 - Right Front Wheel Speed Sensor "A" Range/Performance Signal range check Front right wheel speed sensor signal Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C050D - Left Rear Wheel Speed Sensor "A" Range/Performance Signal range check Rear left wheel speed sensor signal Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C0513 - Right Rear Wheel Speed Sensor "A" Range/Performance Signal range check Rear right wheel speed sensor signal Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C0032 - Left Front Wheel Speed Sensor Supply Signal range check Front left wheel speed sensor under voltage Detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C0035 - Right Front Wheel Speed Sensor Supply Signal range check Front right wheel speed sensor under voltage Detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C0038 - Left Rear Wheel Speed Sensor Supply Signal range check Rear left wheel speed sensor under voltage Detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C003B - Right Rear Wheel Speed Sensor Supply Signal range check Rear right wheel speed sensor under voltage Detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
C051D - Multi-axis Acceleration Sensor Module "A" Missing Calibration Signal range check Longitudinal acceleration sensor Not calibrated [-] Ignition On [-] 5 [s] Continuous 2 DCY
C051C - Multi-axis Acceleration Sensor Module "A" Range/Performance Signal range check Longitudinal acceleration sensor Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
Flexray Signal from Restraints Control Module C0552 - Longitudinal Acceleration Sensor Range/Performance Rationality check Offset of longitudinal acceleration signal 1.1 [m/s2] Ignition On [-] 5 [s] Once / DCY 2 DCY
Signal range check State of longitudinal acceleration signal Error detected [-] Ignition On [-] 5 [s] Continuous 2 DCY
Flexray Signal from ABS C0505 - Left Front Wheel Speed Sensor "A" Correlation Rationality check Deviation of front left wheel speed from vehicle speed during static straight-line travel 2 [km/h] Static straight-line travel 20•••150 [km/h] 5 [s] Continuous 2 DCY
C050B - Right Front Wheel Speed Sensor "A" Correlation Rationality check Deviation of front right wheel speed from vehicle speed during static straight-line travel 2 [km/h] Static straight-line travel 20•••150 [km/h] 5 [s] Continuous 2 DCY
C0511 - Left Rear Wheel Speed Sensor "A" Correlation Rationality check Deviation of rear left wheel speed from vehicle speed during static straight-line travel 2 [km/h] Static straight-line travel 20•••150 [km/h] 5 [s] Continuous 2 DCY
C0517 - Right Rear Wheel Speed Sensor "A" Correlation Rationality check Deviation of rear right wheel speed from vehicle speed during static straight-line travel 2 [km/h] Static straight-line travel 20•••150 [km/h] 5 [s] Continuous 2 DCY
scientia non olet · About LEMON Manuals