LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Buick >> 2017 >> Envision Base >> Repair and Diagnosis >> Accessories & Equipment >> Entertainment Systems >> Cellular System, Entertainment System, And Navigation System >> Diagnostic Information and Procedures >> DTC B124B: USB 1 Circuit >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

  1. Ignition OFF, disconnect the X1 harness connector at the X83 Auxiliary Audio Input.
  2. Test for less than 10 Ω between the ground circuit terminal 4 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Verify that a test lamp illuminates between the B+ circuit terminal 6 and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • If the test lamp illuminates 
  4. Verify the USB cable is properly connected at all components and in-line connections, and there is no damage to the cable or connections.
    • If connection problems or cable damage is noted. 

      Perform the appropriate repair or replacement to correct any issues.

    • If no connection problems or cable damage is noted. 
  5. Connect the X1 harness connector at the X83 Auxiliary Audio Input.
  6. Disconnect the vehicle USB cable X4 harness connector at the K74 Human Machine Interface Control Module and the X83 Auxiliary Audio Input.
  7. Connect the EL-50034 - 14 Infotainment Test Cable and the EL-50334 - 2 Type-A Female to Mini-B Male Cable together. Connect the assembled test cable to the K74 Human Machine Interface Control Module and the X83 Auxiliary Audio Input.
  8. Ignition ON, infotainment system ON.
  9. Connect the EL-50334-20 Multi-Media Interface Tester (MIT) to the X83 Auxiliary Audio Input USB port and select the USB test mode.
  10. Verify the audio from the EL-50334-20 Multi-Media Interface Tester (MIT) is heard through the infotainment system while operating the system to play audio from the test tool.
    • If audio is not heard from the test tool 
    1. Replace the X83 Auxiliary Audio Input. Connect all harness connectors.
    2. Connect the EL-50334-20 Multi-Media Interface Tester (MIT) to the X83 Auxiliary Audio Input USB port and select the USB test mode.
    3. Verify the audio from the EL-50334-20 Multi-Media Interface Tester (MIT) is heard through the infotainment system while operating the system to play audio from the test tool.
      • If audio is not heard from the test tool, replace the K74 Human Machine Interface Control Module.
      • If audio is heard from the test tool.
    4. All OK.
    • If audio is heard from the test tool 
  11. Connect the vehicle USB cable X4 harness connector at the K74 Human Machine Interface Control Module.
  12. Disconnect the console to I/P USB in-line connector. Connect the assembled test cable to the I/P side of the in-line USB cable connector and the X83 Auxiliary Audio Input.
  13. Connect the EL-50334-20 Multi-Media Interface Tester (MIT) to the X83 Auxiliary Audio Input USB port and select the USB test mode.
  14. Verify the audio from the EL-50334-20 Multi-Media Interface Tester (MIT) is heard through the infotainment system while operating the system to play audio from the test tool.
    • If audio is not heard from the test tool 

      Replace the I/P USB cable assembly.

    • If audio is heard from the test tool 
  15. Replace the console USB cable assembly.
scientia non olet · About LEMON Manuals