LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Buick >> 2017 >> Envision Base >> Repair and Diagnosis >> Accessories & Equipment >> Entertainment Systems >> Cellular System, Entertainment System, And Navigation System >> Diagnostic Information and Procedures >> DTC B2476 or B2482: Cellular Phone Select Service Switch >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

  1. Ignition OFF/vehicle OFF and all vehicle systems OFF, disconnect the harness connector at the S51 Telematics Button Assembly. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 6 and ground.
    • If 10 Ω or greater 
    1. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON/vehicle in Service Mode.
  4. Test for 8.0 - 10.5 V between the 10 V reference circuit terminal 1 and the ground circuit terminal 6.
    • If less than 8.0 V 
    1. Ignition OFF/vehicle OFF, disconnect the harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the 10 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 10 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K73 Telematics Communication Interface Control Module.
    • If greater than 10.5 V 
    1. Ignition OFF/vehicle OFF, disconnect the harness connector at the K73 Telematics Communication Interface Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the 10 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K73 Telematics Communication Interface Control Module.
    • If between 8.0 - 10.5 V 
  5. Ignition OFF/vehicle OFF.
  6. Test for 500 - 900 Ω between the signal circuit terminal 3 and the ground circuit terminal 6.
    • If less than 500 Ω 
    1. Disconnect the X1 harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K73 Telematics Communication Interface Control Module.
    • If greater than 900 Ω 
    1. Disconnect the X1 harness connector at the K73 Telematics Communication Interface Control Module, ignition ON/vehicle in Service Mode.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF/vehicle OFF.
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K73 Telematics Communication Interface Control Module.
    • If between 500 - 900 Ω 
  7. Test or replace the S51 Telematics Button Assembly.
scientia non olet · About LEMON Manuals