Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION / PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Drive Shaft Nut | |||
| Front or Rear | First Pass: 37 lb ft (50 N.m) Final Pass: 60 degrees |
||
| Battery | BATTERY INSPECTION / TEST or BATTERY ELECTRICAL DRAIN / PARASITIC LOAD TEST | ||
| Brakes | |||
| Bleeding Sequence | Right Rear, Left Rear, Right Front, Left Front, refer to HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | CHARGING SYSTEM TEST | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | Refer to the illustration under Drive Belt Replacement | ||
| LE2 | DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| LE2 | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT | ||
| Water Pump R & I | |||
| LE2 | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| LE2 | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure - @1500 RPM 100° C | 29 - 36 psi (200 - 250 kPa) | ||
| Overhaul | REPAIR INSTRUCTIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | Refer to FLUIDS under the MAINTENANCE / FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel / Flex Plate / Drive Plate Torque | |||
| LE2 | First Pass: 20 N.m (15 lb ft) Second Pass: 30 N.m (22 lb ft) Final Pass: 70 Degrees |
||
| Fuel System | |||
| Fuel Pressure Test Procedure | LE2 FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Strainer is located at lower end of the fuel tank fuel pump module | ||
| Fuel Filter R & I | |||
| LE2 | Fuel Tank Fuel Pump Module Replacement (FWD) or Fuel Tank Fuel Pump Module Replacement (AWD) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 4 CYLINDER ENGINE | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| LE2: Refer to Electronic Parts Catalogue | |||
| Gap | 0.60-0.70 mm (0.024-0.028 in) | ||
| Torque | 13 lb ft (17 N.m) | ||
| Starting | |||
| Starter | |||
| Starter Replacement (LE2-FWD) or Starter Replacement (LE2-AWD) | |||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 lb ft (140 N.m) For Wheel Nut Tightening Sequence, refer to the illustration under wheel and tire Installation Procedure | ||