Driver Seat Module

The scan tool displays the voltage level of the battery voltage supply circuit to the driver seat module.

The scan tool displays Off, High, Med, or Low depending on the current heat level operating mode.

The scan tool displays 0.0-5.0 volts. The voltage displayed is an input to the driver seat module from the driver seat heat sensor.

The scan tool displays Off, Back Only, or Back and Cushion depending on the current heat zone operating mode.

The scan tool displays Active or Inactive. When the front vertical adjuster switch is operated in the downward direction the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the front vertical adjuster motor is commanded to move the front of the seat downward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the front vertical adjuster motor is commanded to move the front of the seat upward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the front vertical seat position sensor.

The scan tool displays Active or Inactive. When the front vertical adjuster switch is operated in the upward direction the scan tool displays Active.

The scan tool displays Active or Inactive. When the horizontal seat adjuster switch is operated in the forward direction the scan tool displays Active.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the lumbar support position sensor.

The scan tool displays Active or Inactive. Whenever the horizontal adjuster motor is commanded to move the seat forward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the horizontal adjuster motor is commanded to move the seat rearward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the horizontal seat position sensor.

The scan tool displays Active or Inactive. When the horizontal seat adjuster switch is operated in the rearward direction the scan tool displays Active.

The scan tool displays Active or Inactive. When the lumbar switch is operated in the forward direction the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the lumbar adjuster motor is commanded to move the lumbar support forward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the lumbar adjuster motor is commanded to move the lumbar support rearward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. When the lumbar switch is operated in the rearward direction the scan tool displays Active.

The scan tool displays 0-65535 counts. The value displayed is the front vertical seat position sensor counts stored by the driver seat module as the memory 1 position setting.

The scan tool displays 0-65535 counts. The value displayed is the horizontal seat position sensor counts stored by the driver seat module as the memory 1 position setting.

The scan tool displays 0-65535 counts. The value displayed is the rear vertical seat position sensor counts stored by the driver seat module as the memory 1 position setting.

The scan tool displays 0.0-5.0 volts. The value displayed is the recline position sensor signal voltage stored by the driver seat module as the memory 1 position setting.

The scan tool displays 0-65535 counts. The value displayed is the front vertical seat position sensor counts stored by the driver seat module as the memory 2 position setting.

The scan tool displays 0-65535 counts. The value displayed is the horizontal seat position sensor counts stored by the driver seat module as the memory 2 position setting.

The scan tool displays 0-65535 counts. The value displayed is the rear vertical seat position sensor counts stored by the driver seat module as the memory 2 position setting.

The scan tool displays 0.0-5.0 volts. The value displayed is the recline position sensor signal voltage stored by the driver seat module as the memory 2 position setting.

The scan tool displays Off, High, Med, or Low depending on the current heat level operating mode.

The scan tool displays 0.0-5.0 volts. The voltage displayed is an input to the driver seat module from the passenger seat heat sensor.

The scan tool displays Off, Back Only, or Back and Cushion depending on the current heat zone operating mode.

The scan tool displays Active or Inactive. When the rear vertical adjuster switch is operated in the downward direction the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the rear vertical adjuster motor is commanded to move the rear of the seat upward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the rear vertical adjuster motor is commanded to move the rear of the seat downward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the rear vertical seat position sensor.

The scan tool displays Active or Inactive. When the rear vertical adjuster switch is operated in the upward direction the scan tool displays Active.

The scan tool displays Active or Inactive. When the recline switch is operated in the forward direction the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the recline adjuster motor is commanded to move the seat back forward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the recline adjuster motor is commanded to move the seat back rearward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays 0.0-5.0 volts. The voltage displayed is an input to the driver seat module from the recline position sensor.

The scan tool displays Active or Inactive. When the recline switch is operated in the rearward direction the scan tool displays Active.

The scan tool displays the version of the software part number in the driver seat module.

The scan tool displays the software identification number in the driver seat module.

The scan tool displays Active or Inactive. When the torso switch is operated in the inward direction the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the torso adjuster motor is commanded to move the torso bolster inward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. Whenever the torso adjuster motor is commanded to move the torso bolster outward, due to a manual switch input or a memory recall function, the scan tool displays Active.

The scan tool displays Active or Inactive. When the torso switch is operated in the outward direction the scan tool displays Active.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the torso bolster position sensor.

The scan tool displays 0-65535 counts. The counts displayed are calculated by the driver seat module using the signal circuit input from the lumbar support position sensor.