LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2017 >> CTS Base, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Cellular System, Entertainment System, And Navigation System - Diagnostic Information And Procedures >> Diagnostic Information and Procedures >> DTC B2476 or B2482 (UI3): Cellular Phone Select Service Switch Open >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

NOTE:
  • 10 V reference circuit measurement may vary with vehicle battery voltage.
  • Test for voltage range with vehicle battery measuring at a minimum of 11.5 V
  1. Ignition/Vehicle OFF and all vehicle systems OFF, disconnect the harness connector at the S51 Telematics Button Assembly. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 6 and ground.
    • If 10 Ω or greater 
    1. Ignition/Vehicle OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON/Vehicle in Service Mode.
  4. Test for 8.0-10.5 V between the 10 V reference circuit terminal 1 and ground.
    • If less than 8.0 V 
    1. Ignition/Vehicle OFF, disconnect the harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the 10 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the 10 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K73 Telematics Communication Interface Control Module.
    • If greater than 10.5 V 
    1. Ignition/Vehicle OFF, disconnect the harness connector at the K73 Telematics Communication Interface Control Module, vehicle in Service Mode/Ignition ON.
    2. Test for less than 1 V between the 10 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K73 Telematics Communication Interface Control Module.
    • If between 8.0-10.5 V 
  5. Ignition/Vehicle OFF.
  6. Test for 500-900 Ω between the signal circuit terminal 3 and ground.
    • If less than 500 Ω 
    1. Disconnect the X1 harness connector at the K73 Telematics Communication Interface Control Module.
    2. Test for infinite resistance between the signal circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K73 Telematics Communication Interface Control Module.
    • If greater than 900 Ω 
    1. Disconnect the X1 harness connector at the K73 Telematics Communication Interface Control Module, vehicle in Service Mode/Ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Vehicle OFF.
    4. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K73 Telematics Communication Interface Control Module.
    • If between 500-900 Ω 
  7. Test or replace theS51 Telematics Button Assembly.
scientia non olet · About LEMON Manuals