Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications | ||
| Wheel Drive Shaft Nut | |||
| Front or Rear | First Pass: 150 N.m (111 lb ft) Second Pass: Loosen 45 degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | Battery Inspection/Test , or Battery Electrical Drain/Parasitic Load Test | ||
| Brakes | |||
| JE5, J6G Bleeding Sequence: LR, LF, RF, RR J55 Bleeding Sequence: RF Upper, LF Upper, LR, RR Hydraulic Brake System Bleeding (JE5, J6G) , or Hydraulic Brake System Bleeding (J55) |
|||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Charging System Test | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See graphic at "Accessory Drive Belt Routing" under: Accessory Drive Primary Belt Replacement 2.0L (LSY) , or Accessory Drive Primary Belt Replacement 2.7L (L3B) , or Accessory Drive Primary Belt Replacement 3.6L (LF4) | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Radiator Surge Tank Cap Testing | ||
| Thermostat R & I | Engine Coolant Flow Control Valve Replacement 2.0L (LSY) , or Engine Coolant Flow Control Valve Replacement 2.7L (L3B) , or Engine Coolant Thermostat Housing Replacement 3.6L (LF4) | ||
| Water Pump R & I | Electric Engine Coolant Pump Replacement 2.0L (LSY) , or Electric Engine Coolant Pump Replacement 2.7L (L3B) | ||
| Engine Mechanical | |||
| Compression | Engine Compression Test 2.0L (LSY) , or Engine Compression Test 2.7L (L3B) , or Engine Compression Test 3.6L (LF4) | ||
| Oil Pressure | 2.0L: @ 1500 RPM 100°C - 199.95 kPa (29 psi) 2.7L: @ Pressure Sensor Location @ 1500 RPM - 230 - 170 kPa (33.36 - 24.66 psi) 2.7L: @ Oil Filter Adapter @ 1500 RPM - 230 - 180 kPa (33.36 - 26.11 psi) 3.6L: Minimum @ Idle - 69 kPa (10 psi) 3.6L: Minimum @ 2000 RPM - 138 kPa (20 psi) 3.6L: Piston Cooling Jet Valve Opening Pressure - 2.2 - 3.0 bar (32.3 - 44 psi) |
||
| Overhaul | Engine Mechanical Specifications 2.0L (LSY) , or Engine Mechanical Specifications 2.7L (L3B) , or Engine Mechanical Specifications 3.6L (LF4) | ||
| Torque | 2.0L: Fastener Specifications 2.0L (LSY) 2.7L: Fastener Specifications 2.7L (L3B) 3.6L: Fastener Specifications 3.6L (LF4) |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | 2.0 / 2.7L: First Pass: 15 N.m (11 lb ft) 2.0 / 2.7L: Final Pass: 75 degrees 3.6L: First Pass: 30 N.m (22 lb ft) 3.6L: Final Pass: 45 degrees |
||
| Fuel System | |||
| Fuel Pressure | Circuit/System Verification 2.0L (LSY) , or Circuit/System Verification 2.7L (L3B) , or Circuit/System Verification 3.6L (LF4) | ||
| Fuel Filter Location | Inside the fuel tank. Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | Fuel Tank Fuel Pump Module Replacement 2.0L (LSY) , or Fuel Tank Fuel Pump Module Replacement 2.7L (L3B) , or Fuel Tank Fuel Pump Module Replacement 3.6L (LF4) (MG9) , or Fuel Tank Fuel Pump Module Replacement 3.6L (LF4) (MHU) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires (Resistance) | Individual Ignition Coils | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| Type - See parts catalog | |||
| 2.0L | |||
| Gap | 0.70 - 0.80 mm (0.028 - 0.031 in) | ||
| Torque | 17 N.m (13 lb ft) | ||
| 2.7L | |||
| Gap | 0.65 - 0.75 mm (0.025 - 0.029 in) | ||
| Torque | 17 N.m (13 lb ft) | ||
| 3.6L | |||
| Gap | 0.90 mm (0.035 in) | ||
| Torque | 18 N.m (13 lb ft) | ||
| Starting | |||
| Starter | Starter Replacement 2.0L (LSY) , or Starter Replacement 2.7L (L3B) , or Starter Replacement 3.6L (LF4) | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) See graphic at "Wheel Nut Tightening Sequence" under: Installation Procedure |
||