Specifications Index
LUMINA & MONTE CARLO SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM GENERAL SERVICING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 151 Ft. Lbs. (205 N.m) | ||
| Battery | See BATTERY SPECIFICATIONS table under CAPACITIES . | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | see GENERATOR USAGE/AMP OUTPUT RATING table under DESCRIPTION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | See appropriate graphic under SERPENTINE BELT ROUTING & ALIGNMENT -- CARS . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 15 psi or specification stamped on cap. | ||
| Thermostat R & I | |||
| 3.1L V6 | THERMOSTAT | ||
| 3.8L V6 | NA | ||
| Water Pump R & I | |||
| 3.1L V6 | WATER PUMP | ||
| 3.8L V6 | WATER PUMP | ||
| Engine Mechanical | |||
| 3.1L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Minimum allowable is 15 psi (4.2 kg/cm2 ) @ 1850 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.8L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil pressure | Normal pressure is 60 psi (1 kg/cm2 ) @ 1100 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 3.1L V6 | 52 Ft. Lbs. (71 N.m) | ||
| 3.8L V6 | |||
| First Step | 11 Ft. Lbs. (15 N.m) | ||
| Final Step | Tighten bolts an additional 50 degrees | ||
| Fuel System | |||
| Pressure Specification | |||
| 3.1L V6 | 41-47 psi (2.9-3.3 kg/cm2 ) | ||
| 3.8L V6 | 48-55 psi (3.4-3.8 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | |||
| 3.1L V6 | FUEL SYSTEM PRESSURE TEST | ||
| 3.8L V6 | FUEL SYSTEM PRESSURE TEST | ||
| Fuel Filter Location and R & I | IN-LINE FUEL FILTER REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.1L V6 | See FIRING ORDER & CYLINDER IDENTIFICATION . | ||
| 3.8L V6 | See FIRING ORDER & CYLINDER IDENTIFICATION . | ||
| Ignition Wires (Resistance) | |||
| 3.1L V6 | HIGH TENSION WIRE RESISTANCE | ||
| 3.8L V6 | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | |||
| 3.1L V6 | See graphic under FIRING ORDER . | ||
| 3.8L V6 | NA | ||
| Spark Plug | |||
| 3.1L V6 (AC 41-940) | |||
| Gap | .060 in. (1.52 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| 3.8L V6 (AC 41-921) | |||
| Gap | .060 in. (1.52 mm) | ||
| Torque | 20 Ft. Lbs. (27 N.m) | ||
| Starting | |||
| Starter | See appropriate STARTER IDENTIFICATION table under STARTER IDENTIFICATION . | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (140 N.m) | ||