Specifications Index
TRACKER SPECIFICATIONS INDEX
| System | Specifications/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | N/A | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING SEQUENCE | ||
| Disc Brakes | FRONT DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | REAR DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | See appropriate illustration under SERPENTINE BELT ROUTING & ALIGNMENT | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 15 psi or specification stamped on cap. | ||
| Thermostat R & I | |||
| 1.6 L | N/A | ||
| 2.0 L | THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 1.6 L | WATER PUMP | ||
| 2.0 L | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 1.6 L | With engine at normal operating temperature, oil pressure should be 47.0-61.1 psi (3.2-4.2 kg/cm2 ) at 4000 RPM. Oil pressure relief valve opens at 56.9 psi (4.0 kg/cm2 ). | ||
| 2.0 L | With engine at normal operating temperature, oil pressure range should be 56-67 psi (3.9-4.7 kg/cm2 ) at 4000 RPM. | ||
| Overhaul | |||
| 1.6 L | ENGINE SPECIFICATIONS | ||
| 2.0 L | ENGINE SPECIFICATIONS | ||
| Torque | |||
| 1.6 L | TORQUE SPECIFICATIONS | ||
| 2.0 L | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 1.6 L | 58 Ft. Lbs. (79 N.m) | ||
| 2.0 L | 51 Ft. Lbs. (70 N.m) | ||
| Fuel System | |||
| Pressure Specification | 36-43 psi (2.5-3.0 kg/cm2 Pressure should maintain at least 26 psi (1.8 kg/cm2 ) for one minute after fuel pump is turned off. | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST | ||
| Fuel Filter Location and R & I | REMOVAL PROCEDURE (TRACKER) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | See FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| Type | |||
| 1.6 L | Denso K20PR-U11 NGK BKR6E-11 |
||
| 2.0 L | Denso SK16PR11 Or PK16PR11 NGK 1FR5G11 Or PFR5G-11 |
||
| Gap | .039-.043 In. (1.0-1.1 mm) | ||
| Torque | 18 Ft. Lbs. (25 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 70 Ft. Lbs. (95 N.m) | ||