LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2006 >> SSR Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - 6.0L - DTC P0136 To DTC P0446 >> DTC P0222 >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step verifies that a condition exists.
  2. 4:  The TP sensors share a 5-volt reference circuit. If both DTCs P0122 and P0222 set, test for a condition in the 5-volt reference circuit.
  3. 5:  The ECM produces a measurable steady-state amperage that provides the 5-volt reference to the TP sensors. If the amperage on the 5-volt reference circuit is less than 50 mA, test the 5-volt reference circuit for an open or a high resistance.
  4. 6:  This step tests the signal 2 circuit of the TP sensor. If the TP sensor 2 voltage parameter is not 4.8-5.2 volts, test for a condition in the signal 2 circuit.
DTC P0222

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls Connector End Views or Engine Control Module (ECM) Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the TP sensor 2 voltage parameter with a scan tool.
Is the voltage less than the specified value?		 0.35 V Go to Step 4  Go to Step 3 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 4  Go to Diagnostic Aids
4  Observe the DTC information with a scan tool.
Did DTC P0122 also set?		 - Go to Step 5  Go to Step 6 
5 
  1. Turn OFF the ignition.
    2. NOTE: Refer to Disengaging Connectors Notice in Cautions and Notices.
  2. Disconnect the throttle body harness connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Set-up a DMM to test amperage on the 400 mA scale.
  5. Measure the amperage from the 5-volt reference circuit of the throttle position (TP) sensor to a good ground.
Is the amperage more than the specified value?		 50 mA Go to Step 9  Go to Step 7 
6 
  1. Turn OFF the ignition.
    2. NOTE: Refer to Disengaging Connectors Notice in Cautions and Notices.
  2. Disconnect the throttle body harness connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the TP sensor and the signal 2 circuit of the TP sensor.
  5. Observe the TP sensor 2 voltage parameter with a scan tool.
Is the voltage within the specified range?		 4.8-5.2 V Go to Step 9  Go to Step 8 
7
IMPORTANT: The 5-volt reference circuits are internally connected within the controller. Other sensors that share the 5-volt reference circuit may also have DTCs set. Disconnecting a sensor on the shared 5-volt reference circuit may isolate a shorted sensor. Review the electrical schematic and diagnose the shared circuits and sensors.
Test the 5-volt reference circuit of the TP sensor and all shared 5-volt reference circuits for an open, a short to ground, or for high resistance. Refer to Circuit Testing and Wiring Repairs .Did you find and correct the condition?		 - Go to Step 13  Go to Step 10 
8 Test the signal 2 circuit of the TP sensor for a short to ground, an open, or for high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 10 
9 Test for an intermittent and for a poor connection at the throttle body assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 11 
10 Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 13  Go to Step 12 
11 Replace the throttle body assembly. Refer to Throttle Body Removal .
Did you complete the replacement?		 - Go to Step 13  -
12 Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 13  -
13
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 14 
14 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals