Specifications Index
AVEO SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES (V5 SYSTEM) | ||
| Torque | Automatic System see FASTENER TIGHTENING SPECIFICATIONS Manual System see FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front | 221 ft. lbs. (300 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | right rear, left front, left rear, and right front See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Refer to ADJUSTING BELT TENSION . | ||
| Belt Routing | Refer to figure under ADJUSTING BELT TENSION . | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 1.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT (1.4L/1.6L DOHC) | ||
| Water Pump R & I | |||
| 1.6L | COOLANT PUMP REPLACEMENT (1.4L/1.6L DOHC) | ||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | Compression gage reading should not be less than 100 psi (689 kPa) No reading should be less than 70 percent of the highest reading ENGINE COMPRESSION TEST |
||
| Oil Pressure | NA | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | 26 ft. lbs. (35 N.m) + an additional 30 degrees + an additional 15 degrees |
||
| Fuel System | |||
| Pressure Specification | 55-62 psi (380-427 kPa) | ||
| Fuel Pressure Test Procedure | Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | The fuel filter is contained in the fuel sender assembly inside the fuel tank | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 1.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2,000-12,000 ohms | ||
| Ignition Wires (Routing) | See illustration under SPARK PLUG WIRE REPLACEMENT | ||
| Spark Plug | |||
| 1.6L (Type Woojin - BKR6E-11) | |||
| Gap | 0.039-0.043 in (1.0-1.1 mm) | ||
| Torque | 18 lb ft (25 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 88 ft. lbs. 120 N.m) | ||