Specifications Index

HHR SPECIFICATIONS INDEX

System			Specification/Procedure
Air Conditioning
Service			REFRIGERANT SYSTEM CAPACITIES
Torque			FASTENER TIGHTENING SPECIFICATIONS
Axle Nut/Hub Nut
Front			155 ft. lbs. (210 N.m)
Battery			BATTERY USAGE
Brakes
Bleeding Sequence			RR-LR-RF-LF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) Or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE)
Disc Brakes
Service Specifications			DISC BRAKE COMPONENT SPECIFICATIONS
Torque			FASTENER TIGHTENING SPECIFICATIONS
Drum Brakes
Service Specifications			DRUM BRAKE COMPONENT SPECIFICATIONS
Torque			FASTENER TIGHTENING SPECIFICATIONS
Charging
Generator			GENERATOR USAGE
Torque			FASTENER TIGHTENING SPECIFICATIONS
Drive Belts
Adjustment			Serpentine drive belts are not adjustable
Belt Routing			2.0L See illustrations under DRIVE BELT REPLACEMENT 2.2L & 2.4L See illustrations under DRIVE BELT REPLACEMENT
Engine Cooling
General Service Specifications			NA
Radiator Cap Pressure			Specification is stamped on pressure cap.
Thermostat R & I
2.0L			ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LNF)
2.2L & 2.4L			ENGINE COOLANT THERMOSTAT REPLACEMENT (L61/LE5)
Water Pump R & I
2.0L			WATER PUMP REPLACEMENT (LNF)
2.2L & 2.4L			WATER PUMP REPLACEMENT (LE5, L61)
Engine Mechanical
2.0L
Compression			No cylinder should read less than 100 psi (690 kPa) No cylinder should be less than 70 percent of the highest cylinder ENGINE COMPRESSION TEST
Oil Pressure			Oil Pressure - Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa)
Overhaul			ENGINE MECHANICAL SPECIFICATIONS
Torque			FASTENER TIGHTENING SPECIFICATIONS
2.2L
Compression			No cylinder should read less than 100 psi (690 kPa) No cylinder should be less than 70 percent of the highest cylinder ENGINE COMPRESSION TEST
Oil Pressure			Oil Pressure - Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa)
Overhaul			ENGINE MECHANICAL SPECIFICATIONS (2.2L)
Torque			FASTENER TIGHTENING SPECIFICATIONS (2.2L)
2.4L
Compression			No cylinder should read less than 100 psi (690 kPa) No cylinder should be less than 70 percent of the highest cylinder ENGINE COMPRESSION TEST
Oil pressure			Oil Pressure - Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa)
Overhaul			ENGINE MECHANICAL SPECIFICATIONS (2.4L)
Torque			FASTENER TIGHTENING SPECIFICATIONS (2.4L)
Fluid Specifications			See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque
2.0L, 2.2L & 2.4L A/T & M/T			First pass 39 ft. lbs. (53 N.m) Final pass + an additional 25 degrees
Fuel System
Pressure Specification			2.0L 57-67 psi (395-464 kPa) 2.2L 50-60 psi (345-414 kPa) 2.4L 50-60 psi (345-414 kPa)
Fuel Pressure Test Procedure			2.0L See FUEL PRESSURE GAGE INSTALLATION AND REMOVAL (WITH CH 48027) and FUEL SYSTEM DIAGNOSIS 2.2L & 2.4L See FUEL PRESSURE GAGE INSTALLATION AND REMOVAL and FUEL SYSTEM DIAGNOSIS
Fuel Filter Location			2.0L The fuel strainer attaches to the lower end of the fuel pump module 2.2L The fuel strainer attaches to the lower end of the fuel pump module 2.4L The fuel strainer attaches to the lower end of the fuel pump module
Fuel Filter R & I			2.0L See FUEL PUMP MODULE REPLACEMENT 2.2L & 2.4L See FUEL PUMP MODULE REPLACEMENT
Ignition
FIRING ORDER & CYLINDER IDENTIFICATION			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)			Coil on plug
Ignition Wires (Routing)			Coil on plug
Spark Plug
2.0L (Type NA)
Gap			0.035-0.030 in (0.90-0.75 mm)
Torque			12.5-17 lb ft (17-23 N.m)
2.2L (Type GM P/N 12598004)
Gap			0.043-0.037 in (1.10-0.95 mm)
Torque			15 lb ft (20 N.m)
2.4L (Type NA)
Gap			0.043-0.037 in (1.10-0.95 mm)
Torque			15 lb ft (20 N.m)
Starting
Starter			STARTER MOTOR REPLACEMENT
Torque			FASTENER TIGHTENING SPECIFICATIONS
Wheel Alignment
Adjustment Specifications			WHEEL ALIGNMENT SPECIFICATIONS
Torque			FASTENER TIGHTENING SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque			100 ft. lbs. (140 N.m)