Common Specs & Procedures Index

CAMARO COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		REFRIGERANT SYSTEM SPECIFICATIONS
Torque		FASTENER TIGHTENING SPECIFICATIONS
Axle Nut/Hub Nut
Front		N/A
Rear		199 lb ft (270 N.m)
Battery		BATTERY USAGE
Brakes
Bleeding Sequence		Manual - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) . Pressure - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) .
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Drum Brakes
	Service Specifications	N/A
	Torque	N/A
Charging
Generator		GENERATOR USAGE
Torque		FASTENER TIGHTENING SPECIFICATIONS
Drive Belts
Adjustment		Non-Adjustable Serpentine Belt
Drive Belt Routing		See illustration under DRIVE BELT REPLACEMENT (3.6L)DRIVE BELT REPLACEMENT - (EXCEPT LSA) (6.2L)DRIVE BELT REPLACEMENT - (LSA) (6.2L)
Engine Cooling
General Service Specifications		N/A
	Radiator Cap Pressure	Pressure Stamped On Cap
	Thermostat R & I
	3.6L	ENGINE COOLANT THERMOSTAT REPLACEMENT (LFX)
	6.2L	ENGINE COOLANT THERMOSTAT REPLACEMENT (L99/LS3)ENGINE COOLANT THERMOSTAT REPLACEMENT (LSA)
	Water Pump R & I
	3.6L	WATER PUMP REPLACEMENT (LFX)
	6.2L	WATER PUMP REPLACEMENT (LS3/L99)WATER PUMP REPLACEMENT (LSA)
Engine Mechanical
3.6L
	Compression	No cylinder reading should be less than 965 kPa (140 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST
	Oil Pressure	Minimum @ Idle 69kPa 10psi Minimum @ 2,000 RPM 138 kPa 20psi
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS (LFX)
	Torque	FASTENER TIGHTENING SPECIFICATIONS
6.2L
	Compression	No cylinder should read less than 690 kPa (100 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST
	Oil pressure	41 kPa @ 1,000 RPM 6 psig 124 kPa @ 2,000 RPM 18 psig 165 kPa @ 4,000 RPM 24 psig
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (6.2L LS3)ENGINE MECHANICAL SPECIFICATIONS (6.2L L99)ENGINE MECHANICAL SPECIFICATIONS (6.2L LSA)
	Torque	FASTENER TIGHTENING SPECIFICATIONS (6.2L LS3)FASTENER TIGHTENING SPECIFICATIONS (6.2L L99)FASTENER TIGHTENING SPECIFICATIONS (6.2L LSA)
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque		Auto Trans 3.6 L First Pass (30 N.m) 22 lb ft Final Pass Additional 45 Degrees Manual Trans 3.6 L (67 N.m) 49 lb ft 6.2 L First Pass 20 N.m 15 lb ft 6.2 L Second Pass 50 N.m 37 lb ft 6.2 L Final Pass 100 N.m 74 lb ft
Fuel System
Pressure Specifications		3.6 L Engine at Idle 300-400 kPa (43-58 psi) see CIRCUIT/SYSTEM VERIFICATION 6.2 L W/O Supercharger Engine at Idle 296.4-310.3 kPa (35-45 psi) see CIRCUIT/SYSTEM VERIFICATION 6.2 L With Supercharger Engine at Idle 380-520 kPa (55-76 psi) see CIRCUIT/SYSTEM VERIFICATION
	Fuel Pressure Test Procedure	3.6 L FUEL SYSTEM DIAGNOSIS 6.2 L FUEL SYSTEM DIAGNOSIS (WITHOUT SUPER CHARGER)FUEL SYSTEM DIAGNOSIS (WITH SUPER CHARGER)
	Fuel Filter Location	3.6 L Fuel Filter is Part of the Fuel Tank Fuel Pump Module 6.2 L Fuel Filter is Part of the Fuel Tank Fuel Pump Module
	Fuel Filter R & I	3.6 L FUEL TANK FUEL PUMP MODULE REPLACEMENT - RIGHT SIDE 6.2 L FUEL TANK FUEL PUMP MODULE REPLACEMENT - RIGHT SIDE
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		3.6 L Individual Ignition Coil/Module Assemblies 6.2 L Individual Ignition Coil/Module Assemblies
Ignition Wires (Routing)
3.6 L		Coil on Plug
6.2 L		Coil on Plug
Spark Plug
See parts catalog
	Gap	3.6 L (1.1 mm) 0.043 in
	Torque	3.6 L (20 N.m) 15 lb ft
See parts catalog
	Gap	6.2 L (1.02 mm) 0.40 in
	Torque	6.2 L (15 N.m) 11 lb ft
Starting
Starter		N/A
Torque		FASTENER TIGHTENING SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER TIGHTENING SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		Wheel Nuts with silver tint cone seats (W/ RPO RT2 - WHEEL-18 X 7.5, J, STEEL, DESIGN 1) (190 N.m) 140 lb. ft Wheel Nuts with blue tint cone seats (W/ RPO RT2 - WHEEL-18 X 7.5, J, STEEL, DESIGN 1) (150 N.m) 110 lb ft Wheel Nut Torque (W/O RPO RT2) (165 N.m) 122 lb ft For wheel nut tightening sequence, see illustration under INSTALLATION PROCEDURE for wheel assembly.