Radio Scan Tool Information
Radio Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| Antenna Module | Enabled | The scan tool displays Enabled or Disabled. This indicates if the system uses an antenna module and the output status between the radio and the antenna module. |
| Auxiliary Audio Input | Present | The scan tool displays Present or Not Present. This parameter displays active when an auxiliary input is connected. |
| Battery Voltage | Varies | The scan tool displays volts. This is the voltage at the input to the radio. |
| Digital Radio Receiver | Present | The scan tool displays Present or Not Present. This is the state of the Digital Audio Broadcast. |
| Phone Signal | Present | The scan tool displays Present or Not Present. This parameter will display wether this system uses discrete a phone arbitration or not. |
| Power Mode | Run | The scan tool displays Off, Accessory, Run or Crank Request. This is the power mode radio. |
| Rear Seat Audio | Not Present | The scan tool displays Present or Not Present. This parameter displays Present if the system detects a rear seat audio module. |
| Radio Signal Strength | Varies | This displays the signal strength in dB. This is the signal strength of the radio signal. |
| Theft Lock Armed | Learned VIN | The scan tool displays Learned VIN or No VIN. This is the state of the VIN programming in the radio. |
| Radio Theft Lock Status | Inactive | The scan tool displays Active or Inactive. This is the state of the theft lock system. |
| Valet Mode Status | Inactive | The scan tool displays Active or Inactive. This is the state of the valet mode. |
| Video Display 1 | Inactive | The scan tool displays Active or Inactive. When the rear video display1 is ON, the scan tool will display Active. |
| Video Display 2 | Inactive | The scan tool displays Active or Inactive. When the rear video display2 is ON, the scan tool will display Active. |
| End Model Part Number | Varies | The scan tool displays the end model part number. |
| Boot Software Part Number | Varies | The scan tool displays the boot software ID number. |
| Calibration Part Number 1 | Varies | The scan tool displays the software module ID1. |
| Calibration Part Number 2 | Varies | The scan tool displays the software module ID2. |
| Calibration Part Number 3 | Varies | The scan tool displays the software module ID3. |
| Calibration Part Number 4 | Varies | The scan tool displays the software module ID4. |
| Calibration Part Number 5 | Varies | The scan tool displays the software module ID5. |
| Calibration Part Number 6 | Varies | The scan tool displays the software module ID6. |
| Calibration Part Number 7 | Varies | The scan tool displays the software module ID7. |
| Calibration Part Number 8 | Varies | The scan tool displays the software module ID8. |
| Calibration Part Number 9 | Varies | The scan tool displays the software module ID9. |
| Calibration Part Number 10 | Varies | The scan tool displays the software module ID10. |
| Calibration Part Number 11 | Varies | The scan tool displays the software module ID11. |
| Calibration Part Number 12 | Varies | The scan tool displays the software module ID12. |
| Calibration Part Number 13 | Varies | The scan tool displays the software module ID13. |
| Calibration Part Number 14 | Varies | The scan tool displays the software module ID14. |
| Calibration Part Number 15 | Varies | The scan tool displays the software module ID15. |
| Calibration Part Number 16 | Varies | The scan tool displays the software module ID16. |
| Vin Digits 2-17 | Varies | The scan tool displays the vin digits 2-17. |
| Digital Radio Receiver ID | Varies | The scan tool displays the Digital Audio Broadcast receiver ID. |
| DVD Region Code | Varies | The scan tool displays the DVD region code. |
| DVD Region Code Changes Remaining | Varies | The scan tool displays the number DVD region code changes remaining. |
Radio Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Left Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Left Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Front Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Right Rear Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Center Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Subwoofer Speaker | This output control is used to command the speaker ON and OFF. Commanding the speaker ON will generate a test tone to be generated through the selected loudspeaker. |
| Eject | This output is a reset command to eject the disc. |
| Info Display/Infotainment Faceplate Reset | This output is a reset command to reset the radio display. |
| Info Display/Infotainment Faceplate Wakeup | This output commands a wakeup at the display and the faceplate controls. |
| Clear Hard Disc Drive | This output commands a HDD to clear all customer data. This includes music files, eBooks and navigation addresses. This does not clear Nav database data. |