Common Specs & Procedures Index
(SPARK) COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES (R-1234YF)APPROXIMATE FLUID CAPACITIES (R-134A) | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Axle Nut/Hub Nut (Front) | |||
| First Pass | 37 lb ft (250 N.m) | ||
| Final Pass | An Additional 60 degrees | ||
| Battery | N/A | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL)HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See routing illustration under DRIVE BELT REPLACEMENT (LV7) | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 1.4L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LV7) | ||
| Water Pump R & I | |||
| 1.4L | WATER PUMP REPLACEMENT (LV7) | ||
| Engine Mechanical | |||
| 1.4L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure - @ 1500 RPM 100°C | 200-250 kPa (29-36 psi) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LV7) | ||
| Torque | FASTENER SPECIFICATIONS (LV7) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque (Use NEW Fasteners) | |||
| First Pass | 30 N.m (22 lb ft) | ||
| Final Pass | An Additional 70 Degrees | ||
| Fuel System | |||
| Pressure Specification (Commanded with Scan Tool) | KOEO 345-414 kPa (50-60 psi) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | fuel filter is contained in the fuel sender assembly inside the fuel tank | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (32L (8.5 US GALLON) TANK)FUEL TANK FUEL PUMP MODULE REPLACEMENT (35L (9 US GALLON) TANK) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | |||
| 1.4L | Coil On Plug | ||
| Spark Plug | |||
| 1.4L (Type = Refer to Electronic Parts Catalogue) | |||
| Gap | 0.60-0.70 mm (0.024-0.028 in) | ||
| Torque | 13 lb ft (17 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONSWHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) See tightening sequence illustration under INSTALLATION PROCEDURE | ||