LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2017 >> Sonic LS, 1.8L Eng VIN H, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> System >> Data Communication System >> Diagnostic Information and Procedures >> DTC U007B: Control Module Communication High Speed Extension CAN Bus Off >> Circuit/System Testing >> Testing the Device Circuits
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Testing the Device Circuits

Testing the Device Circuits

  1. Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 10 Ω between each ground circuit terminal at the device that was just disconnected and ground.
    • If 10 Ω or greater 
    1. Ignition/Vehicle OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. If equipped, verify a test lamp illuminates between each B+ circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the disconnected device.
    • If the test lamp illuminates 
  4. Ignition ON/Vehicle In Service Mode.
  5. If equipped, verify a test lamp illuminates between each ignition circuit terminal, which has a fuse in the circuit, and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the disconnected device.
    • If the test lamp illuminates 
  6. If equipped, verify a test lamp illuminates between each ignition circuit terminal, which is controlled by a control module, and ground.
    • If the test lamp does not illuminate 
    1. Ignition/Vehicle OFF, remove the test lamp, disconnect the harness connectors at the control module that controls the ignition circuit.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the control module that controls the ignition circuit.
    • If the test lamp illuminates 
  7. Ignition/Vehicle OFF, all access doors closed, all vehicle systems OFF, and all keys at least 3 m (9.8 ft) away from vehicle. Disconnect the harness connectors at the K56 Serial Data Gateway Module. It may take up to 2 min for all vehicle systems to power down.
  8. Test for less than 2 Ω in each of the gateway expansion high speed GMLAN serial data circuits end to end between the non communicating device and the K56 Serial Data Gateway Module.
    • If 2 Ω or greater 

      Repair the open/high resistance in the serial data circuit.

    • If less than 2 Ω 
  9. Test for less than 2 Ω in each of the primary high speed GMLAN serial data circuits (circuit numbers 2500 & 2501) end to end between the K56 Serial Data Gateway Module and the appropriate X84 Data Link Connector (DLC) terminals listed below.
    • X84 Data Link Connector high speed GMLAN serial data circuit terminal 6
    • X84 Data Link Connector high speed GMLAN serial data circuit terminal 14
    • If 2 Ω or greater 

      Repair the open/high resistance in the high speed GMLAN serial data circuit.

    • If less than 2 Ω 
  10. Replace the non communicating device that was disconnected.
scientia non olet · About LEMON Manuals