Common Specs & Procedures Index
ACADIA COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Approximate Fluid Capacities | |||
| Torque | Fastener Specifications | |||
| Axle Nut/Hub Nut | ||||
| Front Wheel Drive Shaft Nut: 173 lb ft (235 N.m) Rear Wheel Drive Shaft Nut: 151 lb ft (205 N.m) |
||||
| Battery | N/A | |||
| Brakes | ||||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT Hydraulic Brake System Bleeding (Manual) Hydraulic Brake System Bleeding (Pressure) |
|||
| Disc Brakes | ||||
| Service Specifications | Disc Brake Component Specifications | |||
| Torque | Fastener Specifications | |||
| Charging | ||||
| Generator | N/A | |||
| Torque | Fastener Specifications | |||
| Drive Belts | ||||
| Adjustment | Non-Adjustable Serpentine Belt | |||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under Drive Belt Replacement 2.0 (LTG) , or Drive Belt Replacement 3.6 (LFY) |
|||
| Engine Cooling | ||||
| General Service Specifications | N/A | |||
| Radiator Cap Pressure | Pressure Stamped On Cap | |||
| Thermostat R & I | ||||
| Engine Coolant Thermostat Housing Replacement 2.0 (LTG) , or Engine Coolant Thermostat Housing Replacement 3.6 (LFY) | ||||
| Water Pump R & I | ||||
| Water Pump Replacement 2.0 (LTG) , or Water Pump Replacement 3.6 (LFY) | ||||
| Engine Mechanical | ||||
| 3.6L | ||||
| Compression | The lowest reading should not be less than 70 percent of the highest reading. No cylinder reading should be less than 965 kPa (140 psi). Engine Compression Test 2.0 (LTG) , or Engine Compression Test 3.6 (LFY) |
|||
| Oil Pressure - Minimum @ Idle: 69 kPa (10 psi) | Oil Pressure - Minimum @ 2, 000 RPM: 138 kPa (20 psi) | |||
| Overhaul | Engine Mechanical Specifications 2.0 (LTG) , or Engine Mechanical Specifications 3.6 (LFY) | |||
| Torque | Fastener Specifications 2.0 (LTG) , or Fastener Specifications | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flex Plate (3.6L A/T) Torque | First Pass: 30 N.m (22 lb. ft.) Final Pass: Tighten 45° |
|||
| Flex plate (2.0L) Torque | First Pass: 20 N-m (15 lb ft) Second Pass: 30 N-m (22 lb ft) Final Pass: an additional 40 degrees |
|||
| Fuel System | ||||
| Pressure Specification | 3.6L Ignition ON, Engine OFF - 345-690 kPa (50-100 psi) Engine at IDLE - 300-400 kPa (43-58 psi) |
|||
| Fuel Pressure Test Procedure | Circuit/System Verification 2.0L (LTG) , or Circuit/System Verification 3.6L (LFY) | |||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | |||
| Fuel Filter R & I | Fuel Pump Power Control Module Replacement 2.0L (LTG) , or Fuel Pump Power Control Module Replacement 3.6L (LFY) (FWD) , or Fuel Pump Power Control Module Replacement 3.6 (LFY) (AWD) | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | |||
| Ignition Wires (Routing) | ||||
| 3.6L | Coil On Plug | |||
| Spark Plug - For application, see parts catalog | ||||
| 3.6L | ||||
| Gap | 0.95-1.1 mm (0.037-0.043 in) | |||
| Torque | 13 lb ft (18 N.m) | |||
| 2.0L | ||||
| Gap | .95-1.1 mm (0.037-0.043 in) | |||
| Torque | (15 lb ft) 20 N-m | |||
| Starting | ||||
| Starter | N/A | |||
| Torque | Fastener Specifications | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Wheel Alignment Specifications | |||
| Torque | Fastener Specifications | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) For Lug Nut Tightening Sequence, Please See the Figure Under Installation Procedure |
|||