LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2021 >> Tahoe SSV >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Image Display Camera System >> Diagnostic Information and Procedures >> DTC B1594 (in Video Processing Module) >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Circuit/System TestingDTC B1594 29, 82orB1A62 46, 49, 98orB1A9B 00

  1. Ignition - On / Vehicle - In Service Mode
  2. Replace the component: B87 Rearview Driver Information Camera
  3. Verify the DTC does not set.
    • If the DTC is not set 

      All OK.

    • Go to next step: If the DTC sets 
  4. Replace the component: K157 Video Processing Module

Circuit/System TestingDTC B1594 11, 12, 13orB1A62 92

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: X2@K157 Video Processing Module
  3. Wait for greater than 5 s.
  4. Connect appropriate EL-52552pinout tool to K157 Video Processing Module
  5. Ignition - On / Vehicle - In Service Mode
  6. Test for 7 to 11 V between the test points: Signal circuit terminal 2-RD@K157 Video Processing Module & Ground (component side)
    • If not between 7 and 11 V 

      Replace the component: K157 Video Processing Module

    • Go to next step: If between 7 and 11 V 
  7. Ignition/Vehicle & All vehicle systems - Off
    8. NOTE:

    Before testing the coax cable, check the cable's exterior for being pinched, cut, damaged, or having loose connections at the components, all of which can cause reception issues.

  8. Disconnect the electrical connector: B87 Rearview Driver Information Camera
  9. Locate the appropriate pinout adapter and load test loop adapter from EL-52552 COAX FAKRA Cable Adaptor Kit.
  10. Connect the 2 adapters together, measure and record the resistance between the terminals at the pinout adapter.
  11. Disconnect the 2 adapters and connect each one to the appropriate end of the coax cable.
  12. At the pinout adapter test terminals, measure the total resistance of the coax cable loop including the connected load test adapter.
    • If not within 5 Ω of the reading from step 10. 

      Replace the coax cable

    • Go to next step: If within 5 Ω of the reading from step 10. 
  13. Replace the component: B87 Rearview Driver Information Camera
  14. Apply the parking brake.
  15. Engine RunningTransmission in Reverse
  16. Verify the DTC does not set.
    • If the DTC is set 

      Replace the component: K157 Video Processing Module

    • Go to next step: If the DTC is not set 
  17. All OK.

Circuit/System TestingDTC B1A62 54, 55, 76

  1. Ignition - On / Vehicle - In Service Mode
  2. Ensure the Surround Vision System is fully calibrated. Refer to: Video Processing Control Module Calibration 
  3. Verify the DTC does not set.
    • If the DTC is not set 

      All OK.

    • Go to next step: If the DTC sets 
  4. Operate the vehicle under the following conditions:
    • During the day
    • On a straight road
    • Distance Traveled=Greater than 0.5 km (0.3 mi)
  5. Ignition/Vehicle & All vehicle systems - Off
  6. Wait for greater than 60 s.
  7. Ignition - On / Vehicle - In Service Mode
  8. Verify the DTC does not set.
    • If the DTC is not set 

      All OK.

    • Go to next step: If the DTC sets 
  9. Test or replace the component: B87 Rearview Driver Information Camera
  10. Verify the DTC does not set.
    • If the DTC is not set 

      All OK.

    • Go to next step: If the DTC sets 
  11. Test or replace the component: K157 Video Processing Module
scientia non olet · About LEMON Manuals