Installation Procedure
Column Lock Module (1) - Install
- CAUTION:
Refer to Fastener Caution .
Steering Column Lock Control Module Bolt (1) - Install and tighten [4x] - Fastener Specifications
Install the steering column (1) with the upper intermediate steering shaft (2) attached.
- Connect the electrical connectors attached to the steering column.
Steering Column Nut (1) - Install and tighten [4x] - Fastener Specifications
Floor Front Air Outlet Duct - Left Side (1) - Install
Floor Front Air Outlet Duct Bolt (1) - Install and tighten - Fastener Specifications
Instrument Panel Lower Trim Panel Insulator (1) - Install
Instrument Panel Lower Insulator Retainer (1) - Install [2x]
- Enable the SIR System. SIR Disabling and Enabling
Upper Intermediate Steering Shaft (1) @ Intermediate Steering Shaft - Install
If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
- Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
- Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
- Apply thread locking adhesive to the external threads of the component. Adhesives, Fluids, Lubricants, and Sealers
- Ensure there are no gaps in the thread locking adhesive once applied to the component.
- Mid Intermediate Steering Shaft Bolt (1) - Install and tighten - Fastener Specifications
Front Wheelhouse Liner (1) - Install
Front Wheelhouse Liner Bolt (1) - Install and tighten [3x] - Fastener Specifications
Front Wheelhouse Liner Bolt (1) - Install and tighten [3x] - Fastener Specifications
Front Wheelhouse Liner Retainer (2) - Install
- Front Wheelhouse Liner Bolt (1) - Install and tighten [3x] - Fastener Specifications
Front Wheelhouse Liner Bolt (1) - Install and tighten [3x] - Fastener Specifications
{ If equipped } Front Tire Front Air Deflector Bolt (1) - Install and tighten - Fastener Specifications
- Install the left front tire and wheel assembly. Tire and Wheel Removal and Installation (Steel Wheel) , or Tire and Wheel Removal and Installation (Aluminum Wheel)
- Remove the device used to prevent steering column rotation.
Instrument Panel Steering Column Lower Trim Cover (1) - Install
- { If equipped } Electrical Connector - Connect
Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten - Fastener Specifications
Turn the steering wheel approximately 90 degrees to the right of the centered position.
- Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten - Fastener Specifications
Turn the steering wheel approximately 90 degrees to the left of the centered position.
- Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten - Fastener Specifications
- Turn the steering wheel to the centered position.
Clip the instrument panel steering column opening closeout (2) to the instrument panel steering column upper trim cover (1).
Secure the instrument panel steering column upper trim cover (1) to the instrument panel steering column lower trim cover.
Instrument Panel Knee Bolster (1) - Install
Instrument Panel Knee Bolster Bolt (2) - Install and tighten [2x] - Fastener Specifications
- Hood Primary Latch Release Cable Handle (1) - Install
Connect the electrical connectors.
- Instrument Panel Switch Trim Plate (2) - Install
- Instrument Panel Switch Trim Plate Bolt (1) - Install and tighten - Fastener Specifications
Connect the electrical connectors.
- Instrument Panel Trim Pad (2) - Install
- Instrument Panel Trim Pad Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Trim Plate Applique (1) - Install
Instrument Panel Fuse Block Access Hole Cover (1) - Install
Instrument Panel Lower Trim Panel Outer Filler (1) - Install
- Program the column lock module. Control Module References
Refer to Fastener Caution .
Quantity of fasteners may vary based on option content.