Common Specs And Procedures Index
COMMON SPECS AND PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications | ||
| Wheel Drive Shaft Nut | |||
| Front (use NEW Nut) | First Pass: 330 N.m (244 lb ft) Second Pass: Reverse 45 degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | Battery Inspection/Test or Battery Electrical Drain/Parasitic Load Test | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See Hydraulic Brake System Bleeding |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Charging System Test | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the figure under: | ||
| 2.7L | Accessory Drive Primary Belt Replacement | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Radiator Surge Tank Cap Testing | ||
| Thermostat R & I
NOTE:
A conventional thermostat is not used. A rotary valve system is now used to distribute coolant through the engine in a targeted manner.
|
|||
| 2.7L | Engine Coolant Flow Control Valve Replacement | ||
| Water Pump R & I | |||
| 2.7L | Water Pump Module Replacement (4ZR) or Water Pump Module Replacement (- 4ZR) | ||
| Engine Mechanical | |||
| 2.7L | |||
| Compression | Turbocharger equipped engines - Maximum pressure differential 100 kPa (14.5 psi). See Engine Compression Test |
||
| Engine Oil pressure at Pressure Sensor Location | @ 1500 RPM: 24.66 - 33.36 psi (170-230 kPa) | ||
| Engine Oil pressure at Oil Filter Adapter | @ 1500 RPM: 26.11 - 33.36 psi (180-230 kPa) | ||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate Torque | Use NEW bolts | ||
| 2.7L | |||
| Flex Plate | First Pass: 15 N.m (11 lb ft) Final Pass: Additional 75 degrees |
||
| Fuel System | |||
| 2.7L | |||
| Pressure Specification | Ignition ON, Engine OFF: 46-97 psi (320-670 kPa) | ||
| Fuel Pressure Test Procedure | Circuit/System Verification | ||
| Fuel Filter Location | |||
| 2.7L | The fuel filter (strainer) is part of the Fuel Tank Fuel Pump Module. | ||
| Fuel Filter R & I | |||
| 2.7L | See Fuel Tank Fuel Pump Module Replacement (- ULV) or Fuel Tank Fuel Pump Module Replacement (ULV) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.7L See Parts Catalog for Application | |||
| Gap | 0.65 - 0.75 mm (0.025 - 0.029 in) | ||
| Torque | 16 N.m (142 lb in) | ||
| Starting | |||
| Starter R & I | |||
| 2.7L | Starter Replacement | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) Using a torque wrench and the appropriate socket, alternately and evenly tighten the wheel nuts in a crisscross pattern. |
||