LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 1997 >> Probe Base, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 16 (Keyless Entry System - Remote) >> Symptom Tests >> No Communication With Driver Door Module
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

No Communication With Driver Door Module

WARNING: This page is about a different car, the 1997 Lincoln Mark VIII. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect driver's door module 4-pin connector C457. See DRIVER DOOR MODULE  under REMOVAL & INSTALLATION. Measure voltage between ground and Dark Green/Purple wire at driver's door module 4-pin connector C457. If battery voltage is not present, go to next step. If battery voltage is present, go to step 16).
  2. Disconnect driver's door module 16-pin connector C455. Measure voltage between ground and driver's door module 16-pin connector C455 terminal No. 2 (Dark Green/Purple wire). See Figure . If battery voltage is not present, go to next step. If battery voltage is present, repair open in Dark Green/Purple wire between driver's door module 4-pin connector C457 and splice. See WIRING DIAGRAM  . Retest system.
  3. Remove fuse No. 41 (10-amp) from instrument panel fuse block. Check condition of fuse. If fuse is blown, go to next step. If fuse is okay, repair open in Dark Green/Purple wire between instrument panel fuse block and driver's door module, then retest system.
  4. Disconnect driver's door module 22-pin connector C456. Remove fuse No. 41 (10-amp) from instrument panel fuse block. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, go to step 10).
  5. Disconnect driver's door lock switch connector. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, replace driver's door lock switch, then retest system.
  6. Disconnect passenger's door lock switch connector. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, replace passenger's door lock switch, then retest system.
  7. Disconnect keypad connector. See KEYPAD  under REMOVAL & INSTALLATION. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, replace keypad, then retest system.
  8. Disconnect driver's memory seat switch connector. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, replace driver's seat memory switch, then retest system.
  9. Disconnect power mirror adjusting switch connector. Measure resistance between ground and driver's door module 4-pin connector C457 terminal No. 3 (Dark Green/Purple wire). If resistance is less than 10 k/ohms, repair short to ground in Dark Green/Purple wire, then retest system. If resistance is greater than 10 k/ohms, power mirror adjusting switch, then retest system.
  10. Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 1 (Pink/Black wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, go to step 13).
  11. Disconnect driver's door lock motor connector. Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 1 (Pink/Black wire). If resistance is less than 10 k/ohms, go to next step. If resistance is greater than 10 k/ohms, replace driver's door lock motor, then retest system.
  12. Disconnect passenger's door lock motor connector. Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 1 (Pink/Black wire). If resistance is less than 10 k/ohms, repair short to ground in Pink/Black wire, then retest system. If resistance is greater than 10 k/ohms, replace passenger's door lock motor, then retest system.
  13. Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 6 (Pink/Yellow wire). Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 17 (Pink/Light Green wire). If resistance is greater than 10 k/ohms, go to next step. If resistance is less than 10 k/ohms, repair short to ground in Pink/Yellow or Pink/Light Green wire, then retest system.
  14. Measure resistance between ground and driver's door module 16-pin connector C455 terminals as follows:
    • Terminal No. 14 (Light Blue/Yellow wire).
    • Terminal No. 6 (Light Green/Red wire).
    • Terminal No. 13 (Yellow/Black wire).
    • Terminal No. 5 (Yellow wire).
    • Terminal No. 12 (Red wire).

    If each resistance measurement is greater than 10 k/ohms, go to next step. If any resistance measurement is less than 10 k/ohms, check suspect circuit(s) for short to ground, then retest system.

  15. Measure resistance between ground and driver's door module 22-pin connector C456 terminals as follows:
    • Terminal No. 18 (Brown/Orange wire).
    • Terminal No. 19 (Brown/Light Green wire).
    • Terminal No. 7 (Black/Orange wire).
    • Terminal No. 20 (Purple/Orange wire).
    • Terminal No. 21 (Dark Blue/Orange wire).
    • Terminal No. 9 (Red/Orange wire).
    • Terminal No. 8 (Dark Green/Orange wire).
    • Terminal No. 10 (Yellow/Black wire).

    If each resistance measurement is greater than 10 k/ohms, replace fuse No. 41 (10-amp) and driver's door module, then retest system. If any resistance measurement is less than 10 k/ohms, check suspect circuit(s) for short to ground, then retest system.

  16. Disconnect driver's door module 16-pin connector C455. Measure voltage between ground and driver's door module 16-pin connector C455 terminal No. 2 (Dark Green/Purple wire). If battery voltage is present, go to next step. If battery voltage is not present, repair open in Dark Green/Purple, then retest system.
  17. Disconnect driver's door module 22-pin connector C456. Measure resistance between ground and driver's door module 22-pin connector C456 terminal No. 16 (Black wire). If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open in Black wire, then retest system.
  18. Measure resistance between ground and driver's door module 16-pin connector C455 terminal No. 8 (Black/Light Blue wire). If resistance is less than 5 ohms, go to MODULE COMMUNICATIONS NETWORK article to diagnose network concern. If resistance is greater than 5 ohms, repair open in Black/Light Blue wire, then retest system.
scientia non olet · About LEMON Manuals