System Specifications

Cylinder Block
Cylinder bore
Diameter 87.5-87.53 mm (3.444-3.445 in)
Maximum out-of-round 0.008 mm (0.0003 in)
Main bearing bore diameter 57.020-57.038 mm (2.244-2.245 in)
Head gasket surface flatness 0.1 mm/general 0.05 mm/200 x 200 (0.004 in/general) (0.0019 in/7.87 x 7.87)

Crankshaft
Main bearing journal
Diameter 51.980-52.000 mm (2.046-2.047 in)
Production repair 51.730-51.750 mm (2.036-2.037 in)
Main bearing clearance 0.019-0.035 mm (0.0007-0.0013 in)
Connecting rod journal
Diameter 49.980-50.000 mm (1.967-1.968 in)
Production repair 49.730-49.750 mm (1.957-1.958 in)
End play 0.22-0.43 mm (0.008-0.016 in)

Connecting Rod
Bearing
Clearance 0.027-0.052 mm (0.001-0.002 in)
Thickness 1.496-1.520 mm (0.058-0.059 in)
Crank bore diameter 53.025-53.045 mm (2.087-2.088 in)
Pin bore diameter 20.965-20.985 mm (0.825-0.826 in)
Length (center to center) 154.8 mm (6.094 in)
Side clearance 1.95-3.05 mm (0.076-0.120 in)
Axial clearance 0.14-0.36 mm (0.005-0.014 in)

Piston
Diameter
(1) 87.5-87.51 mm (3.444-3.445 in)
(2) 87.51-87.52 mm (3.4452-3.4456 in)
(3) 87.52-87.53 mm (3.444-3.446 in)
Clearance-to-bore 0.025-0.045 mm (0.0009-0.0017 in)
Ring groove width
Top 1.203-1.205 mm (0.0473-0.0474 in)
2nd 1.17-1.19 mm (0.0.460-0.0468 in)
Oil 2.501-2.503 mm (0.0984-0.0985 in)
Skirt coating thickness 0.008-0.020 mm (0.0003-0.0007 in)

Piston Pin
Diameter 20.995-21.0 mm (0.8266-0.8268 in)
Length 59.6-60.4 mm (2.346-2.377 in)
Clearance to piston 0.008-0.016 mm (0.0003-0.0006 in)
Clearance to rod Press fit

Rings
Width
Top 1.17-1.185 mm (0.0460-0.0466 in)
2nd 1.197-1.199 mm (0.0471-0.0472 in)
Oil 2.38-2.45 mm (0.093-0.096 in)
Ring gap (in bore)
Top 0.16-0.31 mm (0.006-0.012 in)
2nd 0.33-0.48 mm (0.012-0.018 in)
Oil 0.2-0.7 mm (0.007-0.027 in)

Crankshaft Pulley Bolt

Remove and discard the crankshaft pulley bolt and washer.

First pass 100 Nm (74 lb-ft).
Final pass Tighten an additional 90° (1/4 turn)