Body Control Module (BCM) DTC Table
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1008:23 | Wiper Mode Switch: Signal Stuck Low | INSTALL a new wiper/washer switch. REFER to: STEERING COLUMN MULTIFUNCTION SWITCH RH CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) |
| B1051:92 | Front Washer Switch: Performance or Incorrect Operation | INSTALL a new wiper/washer switch. REFER to: STEERING COLUMN MULTIFUNCTION SWITCH RH CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) |
| B1052:92 | Rear Washer Switch: Performance or Incorrect Operation | INSTALL a new wiper/washer switch. REFER to: STEERING COLUMN MULTIFUNCTION SWITCH RH CLEAR the DTCs and WAIT 10 seconds. REPEAT the self-test. If the DTC is retrieved again, INSTALL a new SASM. REFER to: Steering Angle Sensor Module (SASM) |
| B1087:86 | LIN Bus "A": Signal Invalid | If the exterior lamps are on, REFER to: Headlamps If the exterior lamps are not on, GO to Pinpoint Test B |
| B1087:88 | LIN Bus "A": Bus off | If the exterior lamps are on, REFER to: Headlamps If the exterior lamps are not on, GO to Pinpoint Test B |
| B112B:87 | Steering Wheel Module: Missing Message | GO to Pinpoint Test B |
| B1131:55 | Wiper Motor Module: Not Configured | DIAGNOSE all other DTCs first. If no other DTCs are present, INITIALIZE the windshield wiper motors. REFER to: Windshield Wiper Motor Initialization |
| B1131:83 | Wiper Motor Module: Value of Signal Protection Calculation Incorrect | DIAGNOSE all other Diagnostic Trouble Codes (DTCs) first. CLEAR the Diagnostic Trouble Codes (DTCs). WAIT 10 seconds and REPEAT the BCM self-test. If DTC B1131:83 returns, INSTALL a new driver side windshield wiper motor. |
| B1131:87 | Wiper Motor Module: Missing Message | GO to Pinpoint Test A |
| B129A:86 | LIN Bus "D": Signal Invalid | GO to Pinpoint Test A |
| B129A:88 | LIN Bus "D". Bus off | GO to Pinpoint Test A |
| B1C77:11 | Rear Wiper Relay: Circuit Short To Ground | GO to Pinpoint Test H |
| B1C77:12 | Rear Wiper Relay: Circuit Short To Battery | GO to Pinpoint Test G |
| B1C77:13 | Rear Wiper Relay: Circuit Open | GO to Pinpoint Test G |
| B1C77:14 | Rear Wiper Relay: Circuit Short To Ground or Open | If the rear window wiper is inoperative, GO to Pinpoint Test G If the rear window wiper stays on continuously, GO to Pinpoint Test H |
| B1C77:19 | Rear Wiper Relay: Circuit Current Above Threshold | GO to Pinpoint Test G |
| B1D38:16 | Front Wiper Motor: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| B1D38:17 | Front Wiper Motor: Circuit Voltage Above Threshold | GO to Pinpoint Test A |
| B1D38:19 | Front Wiper Motor: Circuit Current Above Threshold | GO to Pinpoint Test A |
| B1D38:96 | Front Wiper Motor: Component Internal Failure | If only the passenger side windshield wiper motor is inoperative, INSTALL a new passenger side windshield wiper motor. REFER to: Windshield Wiper Motor If both windshield wiper motors are inoperative, INSTALL a new driver side windshield wiper motor. REFER to: Windshield Wiper Motor |
| All other Diagnostic Trouble Codes (DTCs) | - | REFER to: Body Control Module (BCM) |