Specifications Index

POLICE INTERCEPTOR SEDAN SPECIFICATIONS INDEX

System			Specification/Procedure
Air Conditioning
Service			SPECIFICATIONS
Torque			TORQUE SPECIFICATIONS
Axle Nut/Hub Nut
Front			258 Ft. Lbs (350 N.m)
Rear (AWD vehicles)			258 Ft. Lbs (350 N.m)
Battery			SPECIFICATIONS .
Brakes
Bleeding Sequence			R/R, L/R, R/F, L/F BRAKE SYSTEM BLEEDING
Disc Brakes w/Torque
	Front		Refer to the appropriate procedure in FRONT DISC BRAKE SYSTEM
	Rear		Refer to the appropriate procedure in REAR DISC BRAKE SYSTEM
Charging
Generator w/Torque			Refer to appropriate component in CHARGING SYSTEM -->.
Drive Belts
Adjustment			SPECIFICATIONS
Belt Routing			COMPONENT LOCATION
Engine Cooling
General Service Specifications			SPECIFICATIONS
Radiator Cap Pressure			14 psi (96 kPa)
Thermostat R & I			THERMOSTAT -- 3.5L GTDI or THERMOSTAT -- 3.5L TI-VCT, 3.7L TI-VCT or THERMOSTAT HOUSING -- 2.0L GTDI
Water Pump R & I			COOLANT PUMP -- 3.5L GTDI or COOLANT PUMP -- 2.0L GTDI or COOLANT PUMP -- 3.5L TI-VCT, 3.7L TI-VCT .
Engine Mechanical
2.0L GTDI
	Compression		SPECIFICATIONS
	Oil pressure (hot @ 2, 000 rpm)		200 kPa (29.01 psi) - 268 kPa (38.87 psi)
	Overhaul		SPECIFICATIONS
	Torque		SPECIFICATIONS
3.5L Ti-VCT
Compression			SPECIFICATIONS
Oil Pressure Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature			14 Nm (124 lb-in) plus an additional 180 degrees (EOP switch)
Overhaul			SPECIFICATIONS
	Torque		SPECIFICATIONS .
3.5L GTDI
	Compression		SPECIFICATIONS
	Oil Pressure Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature		14 Nm (124 lb-in) plus an additional 180 degrees (EOP switch)
	Overhaul		SPECIFICATIONS
	Torque		SPECIFICATIONS
	3.7L Ti-VCT
		Compression	SPECIFICATIONS
		Oil Pressure Minimum 30 psi @ 1, 500 rpm with engine at normal operating temperature	14 Nm (124 lb-in) plus an additional 180 degrees (EOP switch)
		Overhaul	SPECIFICATIONS
		Torque	SPECIFICATIONS
Fluid Specifications			See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
2.0L GTDI			For tightening sequence, refer to FLEXPLATE Stage 1: Tighten to 50 Nm (37 lb-ft) Stage 2: Tighten to 80 Nm (50 lb-ft) Stage 3: Tighten to 112 Nm (83 lb-ft)
3.5L Ti-VCT			For tightening sequence, refer to FLEXPLATE 80 Nm (59 lb-ft)
3.5L GTDI			For tightening sequence, refer to FLEXPLATE 80 Nm (59 lb-ft)
3.7L Ti-VCT			For tightening sequence, refer to FLEXPLATE 80 Nm (59 lb-ft)
Fuel System
Fuel Filter Location			Located in fuel tank as part of the fuel pump module.
Fuel Filter R & I			FUEL PUMP MODULE
Pressure Release Procedure			FUEL SYSTEM PRESSURE RELEASE .
Pressure Specification			SPECIFICATIONS
Fuel Pressure Test Procedure			FUEL SYSTEM PRESSURE TEST
Ignition
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Routing)			Coil on plug
Spark Plug
2.0L GTDI
	Type		CYFS 12Y 2
	Gap		0.7 mm (0.028 in) - 0.8 mm (0.031 in)
	Torque		Tighten to 12 Nm (106 lb-in)
3.5L Ti-VCT
	Type		CYFS12YT3
Gap			1.30 mm (0.051 in)
Torque			133 Inch Lbs. (15 N.m)
3.5L GTDI
	Type		CYFS12YT3
	Gap		0.81-0.97 mm (0.032-0.038 in)
	Torque		133 Inch Lbs. (15 N.m)
	3.7L Ti-VCT
		Type	CYFS12F5
		Gap	0.051 in. (1.30 mm)
		Torque	133 Inch Lbs. (15 N.m)
Starting
Starter			SPECIFICATIONS
Torque
		2.0L GTDI	Starter Motor Studbolts: 48 Nm (35 lb-ft)
		3.5L GTDI	Starter Motor Studbolts: 48 Nm (35 lb-ft)
		3.5L Ti-VCT	Starter Motor Studbolts: 48 Nm (35 lb-ft)
		3.7L Ti-VCT	Starter Motor Studbolts: 48 Nm (35 lb-ft)
Wheel Alignment
Adjustment Specifications			SPECIFICATIONS
Torque			SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque			All except Police Vehicles 100 Ft. Lbs. (135 N.m) Police Vehicles 110 Ft. Lbs. (149 N.m)