Pinpoint Test BIA: Ignition Status Run/Start Input Battery Input Concern

BIA1 : CHECK FOR DTC U3003:16 AND U3003:17

WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in appropriate GENERAL INFORMATION article. Failure to follow this instruction may result in serious personal injury.

NOTE: Diagnose all network-related (lost communication) DTCs first.

Ignition ON, engine OFF.
Carry out the BECAME self-test.
Is DTC U3003:16 or U3003:17 retrieved DTC during the self-test?

Yes	No
REFER to the DTC/SYMPTOM CHART .	Go to BIA2.

BIA2 : RETRIEVE BECAME DTCS

Ignition ON, engine OFF.
Carry out the BECAME self-test.
Is DTC B1142:62, B11D9:13 or B13BF:14 retrieved during self-test?

Yes	No
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B11D9:13, Go to BIA3. For DTC B1142:62 or B13BF:14, Go to BIA4.	The fault is intermittent. Go to BIA8.

BIA3 : CHECK THE BECAME BATTERY INPUT CIRCUIT FOR VOLTAGE

Ignition OFF.
Depower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
BECAME connector disconnected.

Measure the voltage between:

(+) BECAME Connector, Harness Side	(-)
Fused B+	Ground

Is the voltage greater than 11 volts?

Yes	No
Go to BIA4.	REPAIR the circuit. Go to BIA9.

BIA4 : RETRIEVE BCM DTCS

Are any ignition-related BCM DTCs retrieved during self-test?

Yes	No
DIAGNOSE and REPAIR the BCM DTCs. CLEAR the BECAME DTCs and REPEAT the BECAME self-test. If DTC B1142:62 or B13BF:14 is retrieved during self-test, Go to BIA5.	Key in OFF position. If the BCM does not respond to the scan tool, REFER to: appropriate Module Communications Network article. Go to BIA5.

BIA5 : CHECK THE BECAME IGNITION INPUT CIRCUIT FOR VOLTAGE

Ignition OFF.
Depower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
BECAME connector disconnected.
Repower the SRS. Do not prove out the SRS at this time. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
Ignition ON, engine OFF.

Measure the voltage between:

(+) BECAME Connector, Harness Side	(-)
IGN START/RUN-B	Ground

Is the voltage greater than 11 volts?

Yes	No
Go to BIA6.	REPAIR the circuit. Go to BIA9.

BIA6 : CHECK THE BECAME IGNITION INPUT CIRCUIT FOR A SHORT TO VOLTAGE

Ignition OFF.
Ignition ON, engine OFF.

Measure the voltage between:

(+) BECAME Connector, Harness Side	(-)
IGN START/RUN-B	Ground

Is any voltage present?

Yes	No
REPAIR the circuit. Go to BIA9.	TURN OFF the ignition. INSTALL the BCM fuse required. Go to BIA7.

BIA7 : CONFIRM THE BECAME FAULT

NOTE: Make sure all OCSM components, restraint system sensor electrical connectors and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs are recorded.

Ignition OFF.
Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damaged, pinched, cut or pierced wires.
- repair any concerns found. Refer to appropriate CONNECTOR REPAIR PROCEDURES in OEM Wiring Diagrams article, for schematic and connector information.
Depower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
BECAME connector connected. (if previously disconnected).
Repower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
Ignition ON, engine OFF.
Carry out the BECAME self-test.
Is the original DTC retrieved during self-test?

Yes	No
CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, INSTALL a new BECAME. REFER to: BECAME (Supplemental Restraint System, Removal and Installation). Go to BIA9.	In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. Go to BIA8.

BIA8 : CHECK FOR AN INTERMITTENT FAULT

Ignition OFF.
Depower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
BECAME connector disconnected.
Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damaged, pinched, cut or pierced wires.
- repair any concerns found. Refer to appropriate CONNECTOR REPAIR PROCEDURES in OEM Wiring Diagrams article, for schematic and connector information.
BECAME connector connected.
Repower the SRS. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
Ignition ON, engine OFF.
Carry out the BECAME self-test.
Is DTCs B1142:62, B11D9:13 or B13BF:14 retrieved during self-test?

Yes	No
The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the self-test. Go to BIA4.	CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition frequently. ACTIVATE other system in the same wire harness. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. Go to BIA9.

BIA9 : CHECK FOR ADDITIONAL SRS DIAGNOSTIC TROUBLE CODES (DTCS)

WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

Ignition OFF.
Reconnect all SRS components (if previously disconnected).
If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time. Refer to appropriate SUPPLEMENTAL RESTRAINT SYSTEM article.
Ignition ON, engine OFF.
Clear the RCM DTCs.
Ignition OFF.
Ignition ON, engine OFF.
Wait 10 seconds.
Carry out the RCM self-test.
If equipped with an OCSM, carry out the OCSM self-test.
Carry out the OCS self-test.
If equipped with an BECAME, carry out the BECAME self-test.
Carry out the BECAME self-test.
Are any RCM, OCSM and/or BECM-B DTCs retrieved on-demand during self-test?

Yes	No
Do not clear any DTCs until all DTCs have been resolved. REFER to the RCM OCSM or BECAME DTC Chart.	The repair is complete. RETURN the vehicle to the customer.