| BCM |
B153F:01 |
Power Distribution Box: General Electrical Failure |
GO to Pinpoint Test A |
| BCM |
B153F:08 |
Power Distribution Box: Bus Signal/Message Failure |
GO to Pinpoint Test A |
| BCM |
B153F:49 |
Power Distribution Box: Internal Electronic Failure |
GO to Pinpoint Test A |
| BCM |
B153F:9A |
Power Distribution Box: Component or System Operating Conditions |
GO to Pinpoint Test A |
| BCM |
U0100:87 |
Lost Communication With ECM/PCM "A": Missing Message |
GO to Pinpoint Test B |
| BCM |
U0101:87 |
Lost Communication With TCM: Missing Message |
GO to Pinpoint Test C |
| BCM |
U0121:87 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message |
GO to Pinpoint Test D |
| BCM |
U0131:87 |
Lost Communication With Power Steering Control Module: Missing Message |
GO to Pinpoint Test E |
| BCM |
U0146:87 |
Lost Communication With Serial Data Gateway "A": Missing Message |
GO to Pinpoint Test F |
| BCM |
U0151:87 |
Lost Communication With Restraints Control Module: Missing Message |
GO to Pinpoint Test G |
| BCM |
U0155:87 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message |
GO to Pinpoint Test H |
| BCM |
U0166:87 |
Lost Communication With Auxiliary Heater Control Module: Missing Message |
GO to Pinpoint Test I |
| BCM |
U0184:87 |
Lost Communication With Radio: Missing Message |
GO to Pinpoint Test J |
| BCM |
U0198:87 |
Lost Communication With Telematic Control Module: Missing Message |
GO to Pinpoint Test K |
| BCM |
U0199:87 |
Lost Communication With "Door Control Module A":Missing Message |
GO to Pinpoint Test L |
| BCM |
U0200:87 |
Lost Communication With "Door Control Module B": Missing Message |
GO to Pinpoint Test M |
| BCM |
U0208:87 |
Lost Communication With "Seat Control Module A": Missing Message |
GO to Pinpoint Test N |
| BCM |
U0212:87 |
Lost Communication With Steering Column Control Module: Missing Message |
GO to Pinpoint Test O |
| BCM |
U0214:87 |
Lost Communication With Remote Function Actuation: Missing Message |
GO to Pinpoint Test P |
| BCM |
U0230:87 |
Lost Communication With Rear Gate Module: Missing Message |
GO to Pinpoint Test Q |
| BCM |
U023A:87 |
Lost Communication With Image Processing Control Module A: Missing Message |
GO to Pinpoint Test R |
| BCM |
U0253:87 |
Lost Communication With Accessory Protocol Interface Module: Missing Message |
GO to Pinpoint Test S |
| BCM |
U0293:87 |
Lost Communication With Hybrid/EV Powertrain Control Module "A" : Missing Message |
GO to Pinpoint Test T |
| BCM |
U0515:56 |
Invalid Data Received From Remote Function Actuation: Invalid/Incompatible Configuration |
GO to Pinpoint Test P |
| BCM |
U1000:00 |
Solid State Driver Protection Active: Driver Disabled: No Sub Type Information |
GO to Pinpoint Test U |
| BCM |
U1A4C:55 |
Build/End of Line Mode Active: Not Configured |
REFER to: Factory Mode Deactivation . |
| BCM |
U2005:85 |
Vehicle Speed: Signal Above Allowable Range |
GO to Pinpoint Test V |
| BCM |
U202B:61 |
In-Use Application Signing Key: Signal Calculation Failure |
GO to Pinpoint Test W |
| BCM |
U202B:62 |
In-Use Application Signing Key: Signal Compare Failure |
GO to Pinpoint Test W |
| BCM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test X |
| BCM |
U2101:00 |
Control Module Configuration Inomplete: No Sub Type Information |
GO to Pinpoint Test X |
| BCM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test X |
| BCM |
U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test Y |
| BCM |
U3006:16 |
Control Module Input Power "A": Circuit Voltage Below Threshold |
GO to Pinpoint Test Z |
| BCM |
U3006:17 |
Control Module Input Power "A": Circuit Voltage Above Threshold |
GO to Pinpoint Test AB |
| BCM |
U3006:1C |
Control Module Input Power "A": Circuit Voltage Out of Range |
GO to Pinpoint Test AA |