Information System And Entertainment System DTCS
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B13F7:13 | Audio Input 1: Circuit Open | GO to Pinpoint Test K |
| B13F8:13 | Audio Input 2: Circuit Open | GO to Pinpoint Test K |
| B13F9:13 | Audio Input 3: Circuit Open | GO to Pinpoint Test K |
| B150C:55 | Automobile Audio Bus (A2B) Node 1: Not Configured | GO to Pinpoint Test C |
| B150C:87 | Automobile Audio Bus (A2B) Node 1: Missing Message | GO to Pinpoint Test C |
| B150C:8F | Automobile Audio Bus (A2B) Node 1: Erratic | GO to Pinpoint Test C |
| B1511:01 | Automobile Audio Bus (A2B) Master Node: General Electrical Failure | GO to Pinpoint Test C |
| B1511:11 | Automobile Audio Bus (A2B) Master Node: Circuit Short To Ground | GO to Pinpoint Test C |
| B1511:12 | Automobile Audio Bus (A2B) Master Node: Circuit Short To Battery | GO to Pinpoint Test C |
| B1511:13 | Automobile Audio Bus (A2B) Master Node: Circuit Open | GO to Pinpoint Test C |
| B1511:95 | Automobile Audio Bus (A2B) Master Node: Incorrect Assembly | GO to Pinpoint Test C |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test E |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test E |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test E |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test E |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test E |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test E |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test E |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test E |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test E |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test E |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test E |
| B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test E |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test E |
| B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test E |
| B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test E |
| B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test E |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test E |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test E |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test E |
| B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test E |
| B1A07:13 | Speaker #7: Circuit Open | GO to Pinpoint Test E |
| B1A08:13 | Speaker #8: Circuit Open | GO to Pinpoint Test E |
| B1A09:13 | Speaker #9: Circuit Open | GO to Pinpoint Test E |
| B1A10:13 | Speaker #10: Circuit Open | GO to Pinpoint Test E |
| B1A56:11 | Antenna: Circuit Short To Ground | GO to Pinpoint Test A |
| B1A56:15 | Antenna: Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| B1A89:11 | Satellite Antenna: Circuit Short To Ground | GO to Pinpoint Test B |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to Pinpoint Test B |
| B1D55:11 | Antenna #2: Circuit Short To Ground | GO to Pinpoint Test A |
| B1D55:15 | Antenna #2: Circuit Short To Battery Or Open | GO to Pinpoint Test A |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test Y |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AB |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AE |
| U201A:54 | Control Module Main Calibration Data: Missing Calibration | GO to Pinpoint Test AI |
| U201A:57 | Control Module Main Calibration Data: Invalid/Incompatible Software Component | GO to Pinpoint Test AI |
| U201B:54 | Control Module Calibration Data #2: Missing Calibration | GO to Pinpoint Test AI |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AI |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AJ |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AJ |
| U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test AJ |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG |
| B1087:01 | LIN Bus "A": General Electrical Failure | GO to Pinpoint Test G |
| B108E:01 | Display: General Electrical Failure | GO to Pinpoint Test J |
| B108E:4B | Display: Over Temperature | GO to Pinpoint Test I |
| B108E:4B | Display: Over Temperature | GO to Pinpoint Test J |
| B108E:87 | Display: Missing Message | GO to Pinpoint Test I |
| B108E:87 | Display: Missing Message | GO to Pinpoint Test J |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test R |
| B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test R |
| B1252:11 | USB Port: Circuit Short To Ground | GO to Pinpoint Test N |
| B1252:13 | USB Port: Circuit Open | GO to Pinpoint Test N |
| B12B8:11 | USB Port #2: Circuit Short To Ground | GO to Pinpoint Test N |
| B14FD:11 | External Media Control Connectivity: Circuit Short To Ground | GO to Pinpoint Test N |
| B1D79:11 | Microphone Input: Circuit Short To Ground | GO to Pinpoint Test M |
| B1D79:12 | Microphone Input: Circuit Short To Battery | GO to Pinpoint Test M |
| B1D79:13 | Microphone Input: Circuit Open | GO to Pinpoint Test M |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AL |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AL |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AL |
| U0198:00 | Lost Communication With Telematic Control Module "A": No Sub Type Information | GO to Pinpoint Test AL |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AL |
| U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AM |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AM |
| U1A00:87 | Private Communication Network: Missing Message | GO to Pinpoint Test B |
| U2013:01 | Switch Pack: General Electrical Failure | GO to Pinpoint Test G |
| U2013:16 | Switch Pack: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| U2013:17 | Switch Pack: Circuit Voltage Above Threshold | GO to Pinpoint Test G |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to Pinpoint Test G |
| U2017:45 | Control Module Software #2: Program Memory Failure | GO to Pinpoint Test AN |
| U2017:51 | Control Module Software #2: Not Programmed | GO to Pinpoint Test AN |
| U2017:52 | Control Module Software #2: Not Activated | GO to Pinpoint Test AN |
| U2017:54 | Control Module Software #2: Missing Calibration | GO to Pinpoint Test AN |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AN |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AN |
| U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test AO |
| U3000:09 | Control Module: Component Failures | GO to Pinpoint Test AO |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AO |
| U3000:88 | Control Module: Bus Off | GO to Pinpoint Test AL |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG |
| B13FB:11 | Audio Enable Line: Circuit Short To Ground | GO to Pinpoint Test C |
| B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test F |
| B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test F |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test F |
| B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test F |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test F |
| B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test F |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test F |
| B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test F |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to Pinpoint Test F |
| B1A05:11 | Speaker #5: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A05:12 | Speaker #5: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A05:13 | Speaker #5: Circuit Open | GO to Pinpoint Test F |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test F |
| B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test F |
| B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test F |
| B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test F |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test Z |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AC |
| U0198:00 | Lost Communication With Telematic Control Module "A": No Sub Type Information | GO to Pinpoint Test AD |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AE |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | GO to Pinpoint Test AI |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AI |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AI |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AJ |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AJ |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | GO to Pinpoint Test AJ |
| B1D19:4B | Compact Disc Unit: Over Temperature | GO to Pinpoint Test L |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test Z |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AC |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to Pinpoint Test AJ |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | GO to Pinpoint Test AJ |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AJ |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AJ |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG |
| B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test H |
| B1380:13 | Steering Wheel Right Switch Pack: Circuit Open | GO to Pinpoint Test H |
| B1380:4A | Steering Wheel Right Switch Pack: Incorrect Component Installed | GO to Pinpoint Test H |
| B1380:96 | Steering Wheel Right Switch Pack: Component Internal Failure | GO to Pinpoint Test H |
| B1380:9E | Steering Wheel Right Switch Pack: Stuck On | GO to Pinpoint Test H |
| B116C:04 | External SIM Cable/SIM Card: System Internal Failures | GO to Pinpoint Test AJ |
| B1246:11 | GSM (Group System for Mobile) Antenna: Circuit Short To Ground | GO to Pinpoint Test T |
| B1246:13 | GSM (Group System for Mobile) Antenna: Circuit Open | GO to Pinpoint Test T |
| B1D55:11 | Antenna #2: Circuit Short To Ground | GO to Pinpoint Test U |
| B1D55:13 | Antenna #2: Circuit Open | GO to Pinpoint Test U |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test Y |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test Z |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AE |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AI |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AI |
| U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test AK |
| U3000:09 | Control Module: Component Failures | GO to Pinpoint Test AK |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AJ |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AJ |
| U3000:52 | Control Module: Not Activated | GO to Pinpoint Test AK |
| U3000:56 | Control Module: Invalid/Incompatible Configuration | GO to Pinpoint Test AJ |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AG |