| B11D8:01 |
Restraint Event Notification: General Electrical Failure |
GO to Pinpoint Test A |
| B11D9:09 |
Vehicle Battery: Component Failures |
GO to Pinpoint Test B |
| B11D9:16 |
Vehicle Battery: Circuit Voltage Below Threshold |
GO to Pinpoint Test B |
| B11D9:17 |
Vehicle Battery: Circuit Voltage Above Threshold |
GO to Pinpoint Test B |
| U0100:87 |
Lost Communication With ECM/PCM "A": Missing Message |
GO to Pinpoint Test C |
| U0121:87 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": Missing Message |
GO to Pinpoint Test D |
| U0122:87 |
Lost Communication With Vehicle Dynamics Control Module: Missing Message |
GO to Pinpoint Test E |
| U0131:87 |
Lost Communication With Power Steering Control Module "A": Missing Message |
GO to Pinpoint Test F |
| U0137:87 |
Lost Communication With Trailer Brake Control Module: Missing Message |
GO to Pinpoint Test G |
| U0146:87 |
Lost Communication With Serial Data Gateway "A": Missing Message |
GO to Pinpoint Test H |
| U0151:87 |
Lost Communication With Restraints Control Module: Missing Message |
GO to Pinpoint Test I |
| U0155:87 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message |
GO to Pinpoint Test J |
| U0184:87 |
Lost Communication With Radio: Missing Message |
GO to Pinpoint Test K |
| U0198:87 |
Lost Communication With Telematic Control Module "A": Missing Message |
GO to Pinpoint Test L |
| U0199:87 |
Lost Communication With "Door Control Module A": Missing Message |
GO to Pinpoint Test M |
| U0200:87 |
Lost Communication With "Door Control Module B": Missing Message |
GO to Pinpoint Test N |
| U0208:87 |
Lost Communication With "Seat Control Module A": Missing Message |
GO to Pinpoint Test O |
| U0212:87 |
Lost Communication With Steering Column Control Module: Missing Message |
GO to Pinpoint Test P |
| U0230:87 |
Lost Communication With Rear Gate Module: Missing Message |
GO to Pinpoint Test Q |
| U0232:87 |
Lost Communication With Side Obstacle Detection Control Module "A": Missing Message |
GO to Pinpoint Test R |
| U0233:87 |
Lost Communication With Side Obstacle Detection Control Module "B": Missing Message |
GO to Pinpoint Test R |
| U023A:87 |
Lost Communication With Image Processing Module A: Missing Message |
GO to Pinpoint Test S |
| U0252:87 |
Lost Communication With Lighting Control Module- Rear "B": Missing Message |
GO to Pinpoint Test T |
| U0253:87 |
Lost Communication With Accessory Protocol Interface Module: Missing Message |
GO to Pinpoint Test U |
| U0256:87 |
Lost Communication With Front Controls Interface Module "A": Missing Message |
GO to Pinpoint Test V |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test W |
| U1A4C:55 |
Build / End of Line mode Active: Not Configured |
GO to Pinpoint Test X |
| U2005:85 |
Vehicle Speed: Signal Above Allowable Range |
GO to Pinpoint Test Y |
| U202B:61 |
In-Use Application Signing Key: Signal Calculation Failure |
GO to Pinpoint Test Z |
| U202B:62 |
In-Use Application Signing Key: Signal Compare Failure |
GO to Pinpoint Test Z |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AA |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AA |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test AB |
| U3006:16 |
Control Module Input Power "A" Circuit/Open: Circuit Voltage Below Threshold |
GO to Pinpoint Test AC |
| U3006:17 |
Control Module Input Power "A" Circuit/Open: Circuit Voltage Above Threshold |
GO to Pinpoint Test AD |
| U3006:1C |
Control Module Input Power "A" Circuit/Open: Circuit Voltage Out Of Range |
GO to Pinpoint Test AC |
| U3006:1C |
Control Module Input Power "A" Circuit/Open: Circuit Voltage Out Of Range |
GO to Pinpoint Test AD |
| U3007:16 |
Control Module Input Power "B" Circuit/Open: Circuit Voltage Below Threshold |
GO to Pinpoint Test AC |
| U3007:17 |
Control Module Input Power "B" Circuit/Open: Circuit Voltage Above Threshold |
GO to Pinpoint Test AD |
| U3013:16 |
Control Module Input Power "C" Circuit/Open: Circuit Voltage Below Threshold |
GO to Pinpoint Test AC |
| U3013:17 |
Control Module Input Power "C" Circuit/Open: Circuit Voltage Above Threshold |
GO to Pinpoint Test AD |
| U3014:16 |
Control Module Input Power "D" Circuit/Open: Circuit Voltage Below Threshold |
GO to Pinpoint Test AC |
| U3014:17 |
Control Module Input Power "D" Circuit/Open: Circuit Voltage Above Threshold |
GO to Pinpoint Test AD |