Four Wheel Drive System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B11D9:16 | Vehicle Battery: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| B11D9:17 | Vehicle Battery: Circuit Voltage Above Threshold | GO to Pinpoint Test A |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test B |
| U2002:9E | Switch: Stuck On | GO to Pinpoint Test C |
| U2009:9E | Rotary Encoder: Stuck On | GO to Pinpoint Test D |
| U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test D |
| C00A1:57 | Driveline Control Module: Invalid/Incompatible Software Component | GO to Pinpoint Test E |
| C00A1:F1 | Driveline Control Module: Ethernet 2 Failure | GO to Pinpoint Test E |
| C00A5:01 | Driveline Control Module Transfer Case Unit Control Circuit Driver: General Electrical Failure | GO to Pinpoint Test E |
| C00A5:08 | Driveline Control Module Transfer Case Unit Control Circuit Driver: Bus Signal/Message Failures | GO to Pinpoint Test E |
| C00A5:19 | Driveline Control Module Transfer Case Unit Control Circuit Driver: Circuit Current Above Threshold | GO to Pinpoint Test E |
| C00A5:1C | Driveline Control Module Transfer Case Unit Control Circuit Driver: Circuit Voltage Out Of Range | GO to Pinpoint Test E |
| C00A5:49 | Driveline Control Module Transfer Case Unit Control Circuit Driver: Internal Electronic Failure | GO to Pinpoint Test E |
| C00A5:4B | Driveline Control Module Transfer Case Unit Control Circuit Driver: Over Temperature | GO to Pinpoint Test E |
| C00A5:96 | Driveline Control Module Transfer Case Unit Control Circuit Driver: Component Internal Failure | GO to Pinpoint Test E |
| C00A6:18 | 4WD/AWD Transfer Case Unit Actuator: Circuit Current Below Threshold | GO to Pinpoint Test F |
| C00A6:19 | 4WD/AWD Transfer Case Unit Actuator: Circuit Current Above Threshold | GO to Pinpoint Test F |
| C00A6:4B | 4WD/AWD Transfer Case Unit Actuator: Over Temperature | GO to Pinpoint Test G |
| C00A6:54 | 4WD/AWD Transfer Case Unit Actuator: Missing Calibration | GO to Pinpoint Test H |
| C00A6:66 | 4WD/AWD Transfer Case Unit Actuator: Signal Has Too Many Transitions/Events | GO to Pinpoint Test I |
| C00A6:71 | 4WD/AWD Transfer Case Unit Actuator: Actuator Stuck | GO to Pinpoint Test F |
| C00A6:74 | 4WD/AWD Transfer Case Unit Actuator: Actuator Slipping | GO to Pinpoint Test F |
| C00A6:99 | 4WD/AWD Transfer Case Unit Actuator: Exceeded Learning Limit | GO to Pinpoint Test F |
| C00A7:11 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Short To Ground | GO to Pinpoint Test J |
| C00A7:13 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Open | GO to Pinpoint Test J |
| C00A7:17 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Voltage Above Threshold | GO to Pinpoint Test J |
| C00A8:11 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Short To Ground | GO to Pinpoint Test K |
| C00A8:13 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Open | GO to Pinpoint Test K |
| C00A8:17 | 4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Voltage Above Threshold | GO to Pinpoint Test K |
| P0562:00 | System Voltage Low: No Sub Type Information | GO to Pinpoint Test E |
| P0563:00 | System Voltage High: No Sub Type Information | GO to Pinpoint Test E |
| P0603:00 | Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information | GO to Pinpoint Test E |
| P0604:00 | Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information | GO to Pinpoint Test E |
| P0605:00 | Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information | GO to Pinpoint Test E |
| P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test E |
| P060A:00 | Internal Control Module Monitoring Processor Performance: No Sub Type Information | GO to Pinpoint Test E |
| P060B:00 | Internal Control Module A/D Processing Performance: No Sub Type Information | GO to Pinpoint Test E |
| P060C:00 | Internal Control Module Main Processor Performance: No Sub Type Information | GO to Pinpoint Test E |
| P0630:00 | VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information | GO to Pinpoint Test L |
| P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test E |
| P068A:00 | ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information | GO to Pinpoint Test E |
| P1001:00 | KOER Not Able to Complete, KOER Aborted: No Sub Type Information | GO to Pinpoint Test M |
| P1397:01 | System Voltage Out Of Self Test Range: General Electrical Failure | GO to Pinpoint Test M |
| P1501:00 | Vehicle Speed Sensor Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test M |
| P160A:00 | Control Module Vehicle Options Reconfiguration Error: No Sub Type Information | GO to Pinpoint Test L |
| P166E:00 | Internal Control Module All Wheel Drive Disconnect Control Performance: No Sub Type Information | GO to Pinpoint Test N |
| P1674:00 | Control Module Software Corrupted: No Sub Type Information | GO to Pinpoint Test E |
| P1705:00 | Transmission Range Circuit Not Indicating Park/Neutral During Self Test: No Sub Type Information | GO to Pinpoint Test M |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test O |
| U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to Pinpoint Test O |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test O |
| U0126:00 | Lost Communication With Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test O |
| U0137:00 | Lost Communication With Trailer Brake Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0138:00 | Lost Communication with All Terrain Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test O |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0402:00 | Invalid Data Received from TCM: No Sub Type Information | GO to Pinpoint Test P |
| U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test P |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U0428:00 | Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test P |
| U1012:00 | Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U1014:00 | Invalid Internal Control Module Monitoring Data Received from Restraints Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test L |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test L |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test L |