| C0090:19 |
4WD/AWD Power Transfer Unit Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test A |
| C00A0:00 |
4WD/AWD Rear Differential Unit Actuator 'B' Position Sensor Correlation: No Sub Type Information |
GO to Pinpoint Test B |
| C00A1:57 |
Driveline Control Module: Invalid/Incompatible Software Component |
GO to Pinpoint Test C |
| C00A1:F1 |
Driveline Control Module: Ethernet 2 Failure |
GO to Pinpoint Test D |
| C00A4:1C |
Driveline Control Module Rear Differential Unit 'B' Control Circuit Driver: Circuit Voltage Out Of Range |
GO to Pinpoint Test E |
| C05D8:01 |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: General Electrical Failure |
GO to Pinpoint Test F |
| C05D8:08 |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: Bus Signal/Message Failures |
GO to Pinpoint Test F |
| C05D8:19 |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: Circuit Current Above Threshold |
GO to Pinpoint Test G |
| C05D8:49 |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: Internal Electronic Failure |
GO to Pinpoint Test H |
| C05D8:4B |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: Over Temperature |
GO to Pinpoint Test I |
| C05D8:96 |
4WD/AWD Clutch 'A' Actuator Control Circuit/Open: Component Internal Failure |
GO to Pinpoint Test J |
| C05D9:07 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Mechanical Failures |
GO to Pinpoint Test K |
| C05D9:18 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Circuit Current Below Threshold |
GO to Pinpoint Test K |
| C05D9:44 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test L |
| C05D9:46 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Calibration/Parameter Memory Failure |
GO to Pinpoint Test M |
| C05D9:54 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Missing Calibration |
GO to Pinpoint Test N |
| C05D9:71 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Actuator Stuck |
GO to Pinpoint Test K |
| C05D9:74 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Actuator Slipping |
GO to Pinpoint Test K |
| C05D9:92 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Performance Or Incorrect Operation |
GO to Pinpoint Test K |
| C05D9:99 |
4WD/AWD Clutch 'A' Actuator Control Circuit Performance: Exceeded Learning Limit |
GO to Pinpoint Test K |
| C05E0:1C |
4WD/AWD Clutch 'A' Position Sensor Circuit: Circuit Voltage Out Of Range |
GO to Pinpoint Test O |
| C05E0:86 |
4WD/AWD Clutch 'A' Position Sensor Circuit: Signal Invalid |
GO to Pinpoint Test O |
| C05E7:01 |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: General Electrical Failure |
GO to Pinpoint Test P |
| C05E7:08 |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: Bus Signal/Message Failures |
GO to Pinpoint Test Q |
| C05E7:19 |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: Circuit Current Above Threshold |
GO to Pinpoint Test R |
| C05E7:49 |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: Internal Electronic Failure |
GO to Pinpoint Test S |
| C05E7:4B |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: Over Temperature |
GO to Pinpoint Test T |
| C05E7:96 |
4WD/AWD Clutch 'B' Actuator Control Circuit/Open: Component Internal Failure |
GO to Pinpoint Test U |
| C05E8:07 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Mechanical Failures |
GO to Pinpoint Test R |
| C05E8:18 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Circuit Current Below Threshold |
GO to Pinpoint Test R |
| C05E8:44 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Data Memory Failure |
GO to Pinpoint Test V |
| C05E8:71 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Actuator Stuck |
GO to Pinpoint Test R |
| C05E8:74 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Actuator Slipping |
GO to Pinpoint Test R |
| C05E8:92 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Performance Or Incorrect Operation |
GO to Pinpoint Test R |
| C05E8:99 |
4WD/AWD Clutch 'B' Actuator Control Circuit Performance: Exceeded Learning Limit |
GO to Pinpoint Test R |
| C0689:11 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'A': Circuit Short To Ground |
GO to Pinpoint Test W |
| C0689:13 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'A': Circuit Open |
GO to Pinpoint Test W |
| C0689:17 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'A': Circuit Voltage Above Threshold |
GO to Pinpoint Test W |
| C068A:11 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'B': Circuit Short To Ground |
GO to Pinpoint Test W |
| C068A:13 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'B': Circuit Open |
GO to Pinpoint Test W |
| C068A:17 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'B': Circuit Voltage Above Threshold |
GO to Pinpoint Test W |
| C068B:11 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'C': Circuit Short To Ground |
GO to Pinpoint Test W |
| C068B:13 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'C': Circuit Open |
GO to Pinpoint Test W |
| C068B:17 |
4WD/AWD Clutch 'A' Actuator Position Sensor 'C': Circuit Voltage Above Threshold |
GO to Pinpoint Test W |
| C068C:11 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'A': Circuit Short To Ground |
GO to Pinpoint Test X |
| C068C:13 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'A': Circuit Open |
GO to Pinpoint Test X |
| C068C:17 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'A': Circuit Voltage Above Threshold |
GO to Pinpoint Test X |
| C068D:11 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'B': Circuit Short To Ground |
GO to Pinpoint Test X |
| C068D:13 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'B': Circuit Open |
GO to Pinpoint Test X |
| C068D:17 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'B': Circuit Voltage Above Threshold |
GO to Pinpoint Test X |
| C068E:11 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'C': Circuit Short To Ground |
GO to Pinpoint Test X |
| C068E:13 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'C': Circuit Open |
GO to Pinpoint Test X |
| C068E:17 |
4WD/AWD Clutch 'B' Actuator Position Sensor 'C': Circuit Voltage Above Threshold |
GO to Pinpoint Test X |
| C0690:01 |
4WD/AWD Disconnect Clutch Actuator: General Electrical Failure |
GO to Pinpoint Test Y |
| C0690:08 |
4WD/AWD Disconnect Clutch Actuator: Bus Signal/Message Failures |
GO to Pinpoint Test Y |
| C0690:18 |
4WD/AWD Disconnect Clutch Actuator: Circuit Current Below Threshold |
GO to Pinpoint Test Z |
| C0690:19 |
4WD/AWD Disconnect Clutch Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test Z |
| C0690:1C |
4WD/AWD Disconnect Clutch Actuator: Circuit Voltage Out Of Range |
GO to Pinpoint Test Z |
| C0690:49 |
4WD/AWD Disconnect Clutch Actuator: Internal Electronic Failure |
GO to Pinpoint Test AA |
| C0690:4B |
4WD/AWD Disconnect Clutch Actuator: Over Temperature |
GO to Pinpoint Test AB |
| C0690:71 |
4WD/AWD Disconnect Clutch Actuator: Actuator Stuck |
GO to Pinpoint Test Z |
| C0690:7E |
4WD/AWD Disconnect Clutch Actuator: Actuator Stuck On |
GO to Pinpoint Test Z |
| C0690:7F |
4WD/AWD Disconnect Clutch Actuator: Actuator Stuck Off |
GO to Pinpoint Test Z |
| C0690:96 |
4WD/AWD Disconnect Clutch Actuator: Component Internal Failure |
GO to Pinpoint Test AC |
| C0691:17 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Circuit Voltage Above Threshold |
GO to Pinpoint Test AD |
| C0691:29 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Signal Invalid |
GO to Pinpoint Test AD |
| C0691:34 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Signal High Time Less Than Minimum |
GO to Pinpoint Test AD |
| C0691:35 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Signal High Time Greater Than Maximum |
GO to Pinpoint Test AD |
| C0691:56 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Invalid/Incompatible Configuration |
GO to Pinpoint Test AD |
| C0691:92 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'A': Performance Or Incorrect Operation |
GO to Pinpoint Test AD |
| C0692:17 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Circuit Voltage Above Threshold |
GO to Pinpoint Test AE |
| C0692:29 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Signal Invalid |
GO to Pinpoint Test AE |
| C0692:34 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Signal High Time Less Than Minimum |
GO to Pinpoint Test AE |
| C0692:35 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Signal High Time Greater Than Maximum |
GO to Pinpoint Test AE |
| C0692:56 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Invalid/Incompatible Configuration |
GO to Pinpoint Test AE |
| C0692:92 |
4WD/AWD Disconnect Clutch Actuator Position Sensor 'B': Performance Or Incorrect Operation |
GO to Pinpoint Test AF |
| C0693:14 |
4WD/AWD Disconnect Clutch Speed Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test AG |
| C0693:17 |
4WD/AWD Disconnect Clutch Speed Sensor: Circuit Voltage Above Threshold |
GO to Pinpoint Test AG |
| C0693:64 |
4WD/AWD Disconnect Clutch Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0693:A1 |
4WD/AWD Disconnect Clutch Speed Sensor: System Voltage |
GO to Pinpoint Test AG |
| C0694:14 |
4WD/AWD Clutch 'A' Temperature Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test AH |
| C0694:15 |
4WD/AWD Clutch 'A' Temperature Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test AH |
| C0694:92 |
4WD/AWD Clutch 'A' Temperature Sensor: Performance Or Incorrect Operation |
GO to Pinpoint Test AH |
| C0695:14 |
4WD/AWD Disconnect Clutch Temperature Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test AI |
| C0695:15 |
4WD/AWD Disconnect Clutch Temperature Sensor: Circuit Short To Battery Or Open |
GO to Pinpoint Test AI |
| C0695:92 |
4WD/AWD Disconnect Clutch Temperature Sensor: Performance Or Incorrect Operation |
GO to Pinpoint Test AI |
| P0562:00 |
System Voltage Low: No Sub Type Information |
GO to Pinpoint Test AJ |
| P0563:00 |
System Voltage High: No Sub Type Information |
GO to Pinpoint Test AJ |
| P0603:00 |
Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information |
GO to Pinpoint Test AJ |
| P0604:00 |
Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information |
GO to Pinpoint Test AK |
| P0605:00 |
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information |
GO to Pinpoint Test AK |
| P0607:00 |
Control Module Performance: No Sub Type Information |
GO to Pinpoint Test AK |
| P060A:00 |
Internal Control Module Monitoring Processor Performance: No Sub Type Information |
GO to Pinpoint Test AJ |
| P060B:00 |
Internal Control Module A/D Processing Performance: No Sub Type Information |
GO to Pinpoint Test AL |
| P060C:00 |
Internal Control Module Main Processor Performance: No Sub Type Information |
GO to Pinpoint Test AJ |
| P0630:00 |
VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information |
GO to Pinpoint Test AM |
| P0641:1C |
Sensor Reference Voltage 'A' Circuit/Open: Circuit Voltage Out Of Range |
GO to Pinpoint Test AN |
| P064F:00 |
Unauthorized Software/Calibration Detected: No Sub Type Information |
GO to Pinpoint Test AO |
| P068A:00 |
ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information |
GO to Pinpoint Test AP |
| P1001:00 |
KOER Not Able to Complete, KOER Aborted: No Sub Type Information |
GO to Pinpoint Test AQ |
| P1397:00 |
System Voltage Out Of Self Test Range: No Sub Type Information |
GO to Pinpoint Test AJ |
| P160A:00 |
Control Module Vehicle Options Reconfiguration Error: No Sub Type Information |
GO to Pinpoint Test AX |
| P166E:00 |
Internal Control Module All Wheel Drive Disconnect Control Performance: No Sub Type Information |
GO to Pinpoint Test AR |
| P1674:00 |
Control Module Software Corrupted: No Sub Type Information |
GO to Pinpoint Test AS |
| P1705:00 |
Transmission Range Circuit Not Indicating Park/Neutral During Self Test: No Sub Type Information |
GO to Pinpoint Test AT |
| P181F:00 |
Clutch Control System Performance: No Sub Type Information |
GO to Pinpoint Test AU |
| U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test AV |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AV |
| U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test AV |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AV |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test AV |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AW |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AW |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U0428:00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U1012:00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U1014:00 |
Invalid Internal Control Module Monitoring Data Received from Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AX |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test AX |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test AX |