Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| BCM | B11D9:16 | Vehicle Battery: Circuit Voltage Below Threshold | GO to Pinpoint Test W |
| BCM | B11D9:17 | Vehicle Battery: Circuit Voltage Above Threshold | GO to Pinpoint Test X |
| BCM | B1430:12 | Power Point Relay Reset Output: Circuit Short To Battery | GO to Pinpoint Test A |
| BCM | B1430:14 | Power Point Relay Reset Output: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| BCM | B1435:12 | Power Point Relay Set Output: Circuit Short To Battery | GO to Pinpoint Test A |
| BCM | B1435:14 | Power Point Relay Set Output: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| BCM | B1570:12 | Upfitter Relay 2 Reset Output: Circuit Short To Battery | GO to Pinpoint Test B |
| BCM | B1572:12 | Upfitter Relay 2 Set Output: Circuit Short To Battery | GO to Pinpoint Test B |
| BCM | B15E0:01 | Micro Integrity Fault: General Circuit/Electrical Failure | GO to Pinpoint Test V |
| BCM | U0100:87 | Lost Communication With ECM/PCM 'A': Missing Message | GO to Pinpoint Test C |
| BCM | U0101:87 | Lost Communication with TCM: Missing Message | GO to Pinpoint Test D |
| BCM | U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': Missing Message | GO to Pinpoint Test E |
| BCM | U0131:87 | Lost Communication With Power Steering Control Module 'A': Missing Message | GO to Pinpoint Test F |
| BCM | U0137:87 | Lost Communication With Trailer Brake Control Module: Missing Message | GO to Pinpoint Test S |
| BCM | U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test G |
| BCM | U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test H |
| BCM | U0166:87 | Lost Communication With Auxiliary Heater Control Module: Missing Message | GO to Pinpoint Test I |
| BCM | U0184:87 | Lost Communication With Radio: Missing Message | GO to Pinpoint Test J |
| BCM | U0198:87 | Lost Communication With Telematic Control Module 'A': Missing Message | GO to Pinpoint Test K |
| BCM | U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to Pinpoint Test L |
| BCM | U0232:87 | Lost Communication With Side Obstacle Detection Control Module 'A': Missing Message | GO to Pinpoint Test N |
| BCM | U0233:87 | Lost Communication With Side Obstacle Detection Control Module 'B': Missing Message | GO to Pinpoint Test N |
| BCM | U023A:87 | Lost Communication With Image Processing Module A: Missing Message | GO to Pinpoint Test O |
| BCM | U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test M |
| BCM | U0258:87 | Lost Communication With Radio Transceiver: Missing Message | GO to Pinpoint Test P |
| BCM | U1000:00 | Solid State Driver Protection Active -Driver Disabled: No Sub Type Information | GO to Pinpoint Test Q |
| BCM | U1018:87 | Lost Communication With Generic Function Module: Missing Message | GO to Pinpoint Test R |
| BCM | U2005:85 | Vehicle Speed: Signal Above Allowable Range | GO to Pinpoint Test T |
| BCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test U |
| BCM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test U |
| BCM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test U |
| BCM | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test V |
| BCM | U3006:16 | Control Module Input Power 'A' Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test W |
| BCM | U3006:17 | Control Module Input Power 'A' Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test X |
| BCM | U3006:1C | Control Module Input Power 'A' Circuit/Open: Circuit Voltage Out Of Range | GO to Pinpoint Test W |
| BCM | U3006:1C | Control Module Input Power 'A' Circuit/Open: Circuit Voltage Out Of Range | GO to Pinpoint Test X |
| BCM | U3007:16 | Control Module Input Power 'B' Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test W |
| BCM | U3007:17 | Control Module Input Power 'B' Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test X |
| BCM | U3013:16 | Control Module Input Power 'C' Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test W |
| BCM | U3013:17 | Control Module Input Power 'C' Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test X |
| BCM | U3014:16 | Control Module Input Power 'D' Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test W |
| BCM | U3014:17 | Control Module Input Power 'D' Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test X |