LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> GMC >> 2003 >> Jimmy 2D Utility, Part Time, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 206 (Shift Lock Control) >> Diagnostic Information and Procedures >> DTC B2707: Shift Lock Control Solenoid Control Circuit Is Grounded >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

WARNING: This page is about a different car, the 2003 Saturn Vue. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the automatic transmission shift lock control solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 4:  Tests for ground at the control circuit of the automatic transmission shift lock control solenoid.
DTC B2707

Step Action Yes No
Schematic Reference: Automatic Transmission Shift Lock Control Schematics 
Connector End View Reference:  Body Control System Connector End Views 
1 Did you perform A Diagnostic System Check - Automatic Transmission Shift Lock Control? Go to Step 2  Go to Diagnostic System Check - Automatic Transmission Shift Lock Control 
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the shifter unlock solenoid output control parameter ON and OFF.
Does the automatic transmission shift lock control solenoid turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 3 
3
  1. Turn OFF the ignition.
  2. Connect a test lamp between the automatic transmission shift lock control solenoid voltage supply circuit at the connector of the automatic transmission shift lock control solenoid connector and a good ground.
  3. Turn ON the ignition, with the engine OFF.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 8 
4 
  1. Turn OFF the ignition.
  2. Disconnect the automatic transmission shift lock control solenoid.
  3. Connect a test lamp between the shift lock solenoid control circuit at the connector of the automatic transmission shift lock solenoid and battery positive voltage.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, command the shifter unlock solenoid output control ON and OFF several times.
Does the test lamp illuminate ON and OFF with each command?		 Go to Step 6  Go to Step 5 
5 Test the control circuit of the automatic transmission shift lock control solenoid for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 7 
6 Inspect for poor connections at the harness connector of the automatic transmission shift lock control solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 9 
7 Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 11  Go to Step 10 
8 Repair the open or short to ground in the automatic transmission shift lock control solenoid voltage supply circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?		 Go to Step 11  -
9 Replace the automatic transmission shift lock control solenoid.
Did you complete the replacement?		 Go to Step 11  -
10 Replace the body control module (BCM). Refer to Body Control Module Replacement in Body Control System.
Did you complete the replacement?		 Go to Step 11  -
11
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals