Door Lock Control Module Scan Tool Information (Passenger Door Module)

WARNING: This page is about a different car, the 2009 Cadillac STS. However, it is still accessible from the selected car via links, so may be relevant.

Passenger Door Module Scan Tool Data Parameters

Parameter	System State	Expected Value	Description
Operating Conditions: Ignition ON
Battery Voltage Signal	-	Varies	This displays Volts. This is the current battery voltage signal.
Deadbolt Actuator Command	-	Idle	The scan tool displays Idle, Lock, Unlock or Invalid. This is the state of the deadbolt actuator.
Door Ajar Switch	-	Door Closed	The scan tool displays Door Ajar or Door Closed. This is the state of the door ajar switch.
Door Open Switch	-	Closed	The scan tool displays Open or Closed. This is the state of the door open switch.
Door Lock Switch	-	Idle	The scan tool displays Idle, Lock, Unlock or Invalid. This is the state of the door cylinder switch.
Door Switch Backlight Command	-	Varies	This displays %. This is the commanded door switch backlighting dimming percentage.
Exterior Courtesy Lamp Command	-	Varies	This displays %. This is the commanded exterior courtesy lamps dimming percentage.
Exterior Courtesy Lamp Status	-	Off	The scan tool displays On or Off. This is the state of the exterior courtesy lamps.
Lock Indicator Command	-	Varies	This displays %.
Lock Switch Indicator Command	-	Off	The scan tool displays On or Off. This is the state of the lock switch indicator.
Passenger Door Handle	-	Inactive	The scan tool displays Active or Inactive. This is the state of the passenger door handle.
Psgr. Mirror Heater	-	Inactive	The scan tool displays Active or Inactive. This is the state of the passenger mirror heater.
Psgr. Mirror Horizontal Position	-	Varies	This displays Volts. This is the current passenger mirror horizontal position measured in volts.
Psgr. Mirror Motors Command	-	Idle	The scan tool displays Idle, Fold Out, Fold In, Left, Right, Down or Up. This is the commanded state of the passenger mirror motors.
Psgr. Mirror Vertical Position	-	Varies	This displays Volts. This is the current passenger mirror vertical position measured in volts.
RF Latch Solenoid Command	-	Inactive	The scan tool displays Active or Inactive. This is the state of the passenger front latch solenoid.
VIN Learned	-	Yes	The scan tool displays Yes or No. Yes is displayed if the vehicle identification number (VIN) is learned.
VIN Message Received	-	Yes	The scan tool displays Yes or No. Yes is displayed if the vehicle identification number (VIN) message is received.
Window Motor Command	-	Idle	The scan tool displays Idle, Up, Down or Active. This is the commanded state of the window motor.
Window Normalization	-	Varies	The scan tool displays Yes or No.
Window Switch	-	Idle	The scan tool displays Idle, Invalid, Down, Express Down, Up or Express Up. This is the state of window switch.

Passenger Door Module Scan Tool Output Controls

Output Control	Description
Disable DTC(s)	This output control is used to disable DTCs in the module.
Door Deadbolt Lock/Unlock	This output control is used to command the door deadbolt.
Door Switch Backlight	This output control is used to command the door switch backlighting.
Exterior Courtesy Lamp	This output control is used to command the exterior courtesy lamps.
Front Psgr. Window Motor	This output control is used to command the passenger front window motor.
Lock Switch Indicator	This output control is used to command the lock switch indicator ON or OFF.
Mirror Fold	This output control is used to command the mirror fold.
Mirror Heater	This output control is used to command the mirror heater ON or OFF.
Psgr. Mirror Horizontal Motor	This output control is used to command the passenger mirror horizontal motor.
Psgr. Mirror Vertical Motor	This output control is used to command the passenger mirror vertical motor.
RF Latch Solenoid	This output control is used to command the passenger front latch solenoid.